Spagnuolo, Elena
Preferred name
Spagnuolo, Elena
Email
elena.spagnuolo@ingv.it
Staff
staff
ORCID
Scopus Author ID
36110318400
Researcher ID
E-1376-2017
66 results
Filters
Settings
The search returned 66 results
Now showing 1 - 10 of 66
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Selective clast survival in an experimentally-produced pseudotachylyte
On-fault processes during earthquakes contribute to seismic rupture propagation and slip. Here we investigate clast fragmentation in an experimental pseudotachylyte (solidified seismic melt) produced with a rotary shear machine. We slid for 0.44 m (corresponding to Mw ≥ 6 earthquakes), at slip rates > 1 m/s, pre-cut samples of quartz + phyllosilicates + plagioclase + sillimanite + garnet -bearing ultramylonite, that hosts pseudotachylytes in nature. The ultramylonite minerals extensively preserved as clasts in the experimental pseudotachylyte are quartz, plagioclase, and sillimanite. Garnet is scarcely preserved, despite having a melting temperature similar to plagioclase, probably due to having low thermal shock resistance. This selective clast survival is identical to the one found in the natural pseudotachylytes. Based on these experimental observations and assuming non-equilibrium melting, the preservation of a mineral, as a clast, in the melt appears to be controlled by its thermal shock properties as well as by its melting temperature. Since the mechanical effects of rupture propagation in these experiments were negligible, we conclude that, for Mw ≥ 6 earthquakes, (i) frictional slip and heating of the slipping zone plus (ii) thermomechanical properties of minerals, rather than fault rupture processes, control mineral comminution and clast survival in frictional melts.68 262 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Fault gouge graphitization as evidence of past seismic slip
One moderate- to large-magnitude earthquake (M > 6) nucleates in Earth’s crust every three days on average, but the geological record of ancient fault slip at meters-per-second seismic velocities (as opposed to subseismic slow-slip creep) remains debated because of the lack of established fault-zone evidence of seismic slip. Here we show that the irreversible temperature-dependent transformation of carbonaceous material (CM, a constituent of many fault gouges) into graphite is a reliable tracer of seismic fault slip. We sheared CM-bearing fault rocks in the laboratory at just above subseismic and at seismic velocities under both water-rich and water-deficient conditions and modeled the temperature evolution with slip. By means of micro-Raman spectroscopy and focused-ion beam transmission electron microscopy, we detected graphite grains similar to those found in the principal slip zone of the A.D. 2008 Wenchuan (Mw 7.9) earthquake (southeast Tibet) only in experiments conducted at seismic velocities. The experimental evidence presented here suggests that high-temperature pulses associated with seismic slip induce graphitization of CM. Importantly, the occurrence of graphitized fault-zone CM may allow us to ascertain the seismogenic potential of faults in areas worldwide with incomplete historical earthquake catalogues.418 88 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Ultra-thin clay layers facilitate seismic slip in carbonate faults
Many earthquakes propagate up to the Earth's surface producing surface ruptures. Seismic slip propagation is facilitated by along-fault low dynamic frictional resistance, which is controlled by a number of physico-chemical lubrication mechanisms. In particular, rotary shear experiments conducted at seismic slip rates (1 ms-1) show that phyllosilicates can facilitate co-seismic slip along faults during earthquakes. This evidence is crucial for hazard assessment along oceanic subduction zones, where pelagic clays participate in seismic slip propagation. Conversely, the reason why, in continental domains, co-seismic slip along faults can propagate up to the Earth's surface is still poorly understood. We document the occurrence of micrometer-thick phyllosilicate-bearing layers along a carbonate-hosted seismogenic extensional fault in the central Apennines, Italy. Using friction experiments, we demonstrate that, at seismic slip rates (1 ms-1), similar calcite gouges with pre-existing phyllosilicate-bearing (clay content ≤3 wt.%) micro-layers weaken faster than calcite gouges or mixed calcite-phyllosilicate gouges. We thus propose that, within calcite gouge, ultra-low clay content (≤3 wt.%) localized along micrometer-thick layers can facilitate seismic slip propagation during earthquakes in continental domains, possibly enhancing surface displacement.129 230 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , La distribuzione del radon indoor in alcuni settori della città di Roma. Ricercatori e studenti in un progetto innovativo: dalla raccolta del dato alla stesura di un articolo scientifico
All’interno dei percorsi forma vi di Alternanza ScuolaLavoro un gruppo di ricercatori dell’Istituto Nazionale di Geofisica e Vulcanologia ha proposto e sviluppato con una terza classe del Liceo Scientifico Cavour di Roma un progetto riguardante l’avvicinamento degli studenti al mondo della ricerca scientifica, allo scopo di affrontarla e svilupparla in tu e le sue fasi. Dopo aver spiegato e condiviso l’obiettivo della ricerca con gli alunni, la prima fase del progetto ha riguardato la raccolta dei da tramite l’utilizzo di strumenti di misura; si è in seguito proceduto all’analisi dei dati ottenuti , attraverso un foglio elettronico di calcolo, la produzione di grafici e mappe tema che e infine la scrittura di un articolo scientifico (parte essenziale del lavoro del ricercatore) con la descrizione della ricerca svolta e dei risultati ottenuti . La ricerca ha riguardato la distribuzione del radon indoor in alcuni rioni di Roma. Gli studenti hanno avuto la possibilità di misurare il radon indoor tramite strumenti specifici nelle loro abitazioni e nella loro scuola, di analizzarne la distribuzione spaziale e temporale e di individuare dei casi particolarmente anomali. Sono stati quindi evidenziati i legami tra i valori misura , la geologia del sottosuolo e le tipologie abitative, illustrate per mezzo di mappe tematiche, facendo confluire il tutto o nella scrittura di un articolo scientifico. Il presente rapporto tecnico è stato introdotto dai ricercatori e sviluppato dagli studenti .823 193 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Thermal Weakening Friction During Seismic Slip: Experiments and Models With Heat Sources and Sinks
Experiments that systematically explore rock friction under crustal earthquake conditions reveal that faults undergo abrupt dynamic weakening. Processes related to heating and weakening of fault surfaces have been invoked to explain pronounced velocity weakening. Both contact asperity temperature Ta and background temperature T of the slip zone evolve significantly during high-velocity slip due to heat sources (frictional work), heat sinks (e.g., latent heat of decomposition processes), and diffusion. Using carefully calibrated High-Velocity Rotary Friction experiments, we test the compatibility of thermal weakening models: (1) a model of friction based only on T in an extremely simplified, Arrhenius-like thermal dependence; (2) a flash heating model which accounts for the evolution of both V and T; (3) same but including heat sinks in the thermal balance; and (4) same but including the thermal dependence of diffusivity and heat capacity. All models reflect the experimental results but model (1) results in unrealistically low temperatures and model (2) reproduces the restrengthening phase only by modifying the parameters for each experimental condition. The presence of dissipative heat sinks in stage (3) significantly affects T and reflects on the friction, allowing a better joint fit of the initial weakening and final strength recovery across a range of experiments. Temperature is significantly altered by thermal dependence of (4). However, similar results can be obtained by (3) and (4) by adjusting the energy sinks. To compute temperature in this type of problem, we compare the efficiency of three different numerical approximations (finite difference, wavenumber summation, and discrete integral).55 80 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Fluid pressurisation and earthquake propagation in the Hikurangi subduction zone
(2021-04-30); ; ; ; In subduction zones, seismic slip at shallow crustal depths can lead to the generation of tsunamis. Large slip displacements during tsunamogenic earthquakes are attributed to the low coseismic shear strength of the fluid-saturated and non-lithified clay-rich fault rocks. However, because of experimental challenges in confining these materials, the physical processes responsible for the coseismic reduction in fault shear strength are poorly understood. Using a novel experimental setup, we measured pore fluid pressure during simulated seismic slip in clay-rich materials sampled from the deep oceanic drilling of the Pāpaku thrust (Hikurangi subduction zone, New Zealand). Here, we show that at seismic velocity, shear-induced dilatancy is followed by pressurisation of fluids. The thermal and mechanical pressurisation of fluids, enhanced by the low permeability of the fault, reduces the energy required to propagate earthquake rupture. We suggest that fluid-saturated clay-rich sediments, occurring at shallow depth in subduction zones, can promote earthquake rupture propagation and slip because of their low permeability and tendency to pressurise when sheared at seismic slip velocities.204 115 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Effect of water and rock composition on re-strengthening of cohesive faults during the deceleration phase of seismic slip pulses
The elastic strain energy release rate and seismic waves emitted during earthquakes are controlled by the on-fault temporal evolution of the shear stress during rupture propagation. High velocity friction experiments highlighted that shear stress on the fault surface evolves rapidly during seismic slip pulses. This temporal evolution of shear stress is controlled by both fault weakening at seismic slip initiation and re-strengthening rate towards the end of slip. While numerous studies focused on fault weakening, less attention was given to co-seismic re-strengthening processes. Here we performed 53 friction experiments (normal stress ≤30 MPa, slip-rate ≤6.5 m s−1) imposing constant slip acceleration and deceleration (7.8 m s−2), on cohesive Carrara marble (99% calcite) and micro-gabbro (silicate-built rock) under dry, vacuum and water pressurized conditions. Microstructural observations showed that micro-gabbro accommodated seismic slip by bulk melting of the sliding surfaces, whereas Carrara marble by coupled decarbonation and grain-size dependent crystal plastic processes. Under room humidity conditions and low imposed power density (i.e., product of normal stress per slip rate), re-strengthening rate during the deceleration stage was up to ∼ 17 times faster in marble than in micrograbbro. In the latter, the re-strengthening rate increased slightly with the power density. The presence of water enhanced further this trend. On the contrary, in marbles the re-strengthening rate decreased drastically with power density and in the presence of water. Our experimental observations highlighted the first order importance of the mineralogy and rheology of the slip zone materials and, to a second order, of the presence of water in controlling co-seismic re-strengthening of faults during seismic slip deceleration.141 2 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Fault Friction During Simulated Seismic Slip Pulses
Theoretical studies predict that during earthquake rupture faults slide at non-constant slip velocity, however it is not clear which source time functions are compatible with the high velocity rheology of earthquake faults. Here we present results from high velocity friction experiments with nonconstant velocity history, employing a well-known seismic source solution compatible with earthquake source kinematics. The evolution of friction in experiments shows a strong dependence on the applied slip history, and parameters relevant to the energetics of faulting scale with the impulsiveness of the applied slip function. When comparing constitutive models of strength against our experimental results we demonstrate that the evolution of fault strength is directly controlled by the temperature evolution on and off the fault. Flash heating predicts weakening behavior at short timescales, but at larger timescales strength is better predicted by a viscous creep rheology. We use a steady-state slip pulse to test the compatibility of our strength measurements at imposed slip rate history with the stress predicted from elastodynamic equilibrium. Whilst some compatibility is observed, the strength evolution indicates that slip acceleration and deceleration might be more rapid than that imposed in our experiments.70 100 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Frictional properties of basalt experimental faults and implications for volcano-tectonic settings and geo-energy sites
We performed a suite of experiments aimed at examining the frictional properties of unaltered basalts at conditions considered to be representative of slip at shallow depths in volcano-tectonic environments and in-situ geo-energy basaltic sites. Scientific drilling and field studies on exhumed subsurface faults and fractures analogues suggest that, frictional sliding in basalts can occur in shear zones within a volume of wear debris or along localized joint surfaces. To illuminate how microstructural heterogeneities affect the nucleation of slip instabilities in basalts, we sheared simulated fault gouge and bare rock surfaces at low normal stresses (4–30 MPa) at ambient temperature, under room-dry and wet conditions. We performed velocity steps (0.1–300 μm/s) and slide-hold-slides (30–3000 s holds) to determine the frictional stability and healing properties of basalts. In all the tests, we observed high friction coefficient associated with important frictional restrengthening. Overall, our results show that microstructural heterogeneities strongly affect the friction velocity dependence of basalts: while for normal stresses ≥10 MPa, shear localization accompanied by cataclasis and grain size reduction favors the transition to velocity weakening behavior of powdered samples, on bare surfaces gouge production during shearing promotes a transition to a velocity strengthening behavior. Our results imply that at the tested conditions, friction instabilities may promptly nucleate in shear zones where deformation within (unaltered) basaltic gouge layers is localized, such as those located along volcanic flanks, while joint surfaces characterized by rough rock-on-rock contacts are less prone to unstable slip, which is suppressed at velocities ≥10 μm/s.66 213 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Investigating the effectiveness of rup- ture directivity during the August 24, 2016 Mw 6.0 central Italy earthquake
In this study we investigate directivity effects associated to the August 24, 2016 Mw 6, central Italy earth- quake taking into account the source rupture heterogeneities. We use the directivity predictor proposed by Spudich et al. (2004) which is derived from the isochrones theory. The directivity is computed using a source to site geometry and a focal mechanism. For its simplicity it can be computed once that a moment tensor solution is available. We use this technique to validate the real time solutions. Moreover, because the directivity predictor depends on the rupture velocity it can be used as a proxy to validate the possible rupture history. For the aforementioned reasons our method revealed fruitful for real time applications and helpful to constrain a few main rupture features for further analysis.683 88
