Di Toro, Giulio
Preferred name
Di Toro, Giulio
Email
giulio.ditoro@unipd.it
Staff
staff
ORCID
17 results
Filters
Settings
The search returned 17 results
Now showing 1 - 10 of 17
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Frictional melting of peridotite and seismic slip
(2009-06-13); ; ; ; The evolution of the frictional strength along a fault at seismic slip rates (about 1 m/s) is a key factor controlling earthquake mechanics. At mantle depths, friction-induced melting and melt lubrication may influence earthquake slip and seismological data. We report on laboratory experiments designed to investigate dynamic fault strength and frictional melting processes in mantle rocks. We performed 20 experiments with Balmuccia peridotite in a high-velocity rotary shear apparatus and cylindrical samples (21.8 mm in diameter) over a wide range of normal stresses (5.4–16.1 MPa), slip rates (0.23–1.14 m/s), and displacements (1.5–71 m). During the experiments, shear stress evolved with cumulative displacement in five main stages (stages 1–5). In stage 1 (first strengthening), the coefficient of friction m increased up to 0.4–0.7 (first peak in friction). In stage 2 (abrupt firstweakening), m decreased to about 0.25–0.40. In stage 3 (gradual second strengthening), shear stress increased toward a second peak in friction (m = 0.30–0.40). In stage 4 (gradual second weakening), the shear stress decreased toward a steady state value (stage 5) with m = 0.15. Stages 1 and 2 are of too short duration to be investigated in detail with the current experimental configuration. By interrupting the experiments during stages 3, 4, and 5, microstructural (Field Emission Scanning Electron Microscope) and geochemical (Electron Probe Micro-Analyzer and Energy Dispersive X-Ray Spectroscopy) analysis of the slipping zone suggest that second strengthening (stage 3) is associated with the production of a grain-supported melt-poor layer, while second weakening (stage 4) and steady state (stage 5) are associated with the formation of a continuous melt-rich layer with an estimated temperature up to 1780 C. Microstructures formed during the experiments were very similar to those found in natural ultramafic pseudotachylytes. By performing experiments at different normal stresses and slip rates, (1) the ‘‘thermal’’ (as it includes the thermally activated first and second weakening) slip distance to achieve steady state from the first peak in strength decreased with increasing normal stress and slip rate and (2) the steady state shear stress slightly increased with increasing normal stress and, for a given normal stress, decreased with increasing slip rate. The ratio of shear stress versus normal stress was about 0.15, well below the typical friction coefficient of rocks (0.6–0.8). The dependence of steady state shear stress with normal stress was described by means of a constitutive equation for melt lubrication. The presence of microstructures similar to those found in natural pseudotachylytes and the determination of a constitutive equation that describes the experimental data allows extrapolation of the experimental observations to natural conditions and to the study of rupture dynamics in mantle rocks.278 406 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , The effects of fault orientation and fluid infiltration on fault rock assemblages at seismogenic depths
(2009); ; ; ;Mittempergher, S.; Padova Univ.Pennacchioni, G.; Padova Univ.The factors controlling the development of different types of fault rock assemblages and, more specifically, the formation of friction melts are still not fully understood. In this study we compared two exhumed strike–slip faults in the Adamello batholith (Southern Alps): the Gole Larghe and the Passo Cercen fault zones, active at 9–11 km depth and temperatures of 250–300 C. Each fault zone consists of hundreds of sub-parallel strands exploiting pre-existing joints. The Gole Larghe fault strikes N105 5 and is dextral; the fault rocks are cataclasites and widespread, centimetre-thick pseudotachylytes. The Passo Cercen fault strikes on average N130 and is formed by multiple fault horizons: fault segments striking N105 –N130 are mainly dextral, whereas faults striking N135 –N140 are mainly sinistral. Microstructural, mineralogical and geochemical investigations show that the fault rocks are cataclasites associated with thick epidote þ K-feldspar þ quartz veins and rare, millimetre-thick pseudotachylytes. Field evidence suggests that in both fault zones, the direction of the maximum horizontal stress s1 was N135 . The Gole Larghe fault strikes at about 30 to s1 and is favourably oriented for reactivation. By contrast, the Passo Cercen fault strikes at low angles to s1 and is unfavourably oriented for reactivation, therefore requiring the development of high pore pressures, as suggested by the occurrence of extensive epidote veining and hydraulic breccias. It is proposed that frictional melting in the Passo Cercen fault zone was inhibited by the development of high pore pressures and low effective normal stresses.165 25 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Pseudotachylytes and Earthquake Source Mechanics
(2009); ; ; ;Di Toro, G.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, ItaliaPennacchioni, G.;Destructive earthquakes nucleate at depth (10 to 15 km), therefore monitoring active faults at the Earth’s surface, or interpreting seismic waves, yields only limited information on earthquake mechanics. Tectonic pseudotachylytes (solidified friction-induced melts) decorate some exhumed ancient faults and remain, up to now, the only fault rocks recognized as the unambiguous signature of seismic slip. It follows that pseudotachylyte- bearing fault networks might retain a wealth of information on seismic faulting and earthquake mechanics. In this chapter, we will show that in the case of large exposures of pseudotachylyte-bearing faults, as the glacier-polished outcrops in the Adamello massif (Southern Alps, Italy), we might constrain several earthquake source parameters by linking field studies with microstructural observations, high-velocity rock friction experiments, modeling of the shear heating and melt flow, and dynamic rupture models. In particular, it is possible to estimate the rupture directivity and the fault dynamic shear resistance. We conclude that the structural analysis of exhumed pseudotachylyte-bearing faults is a powerful tool for the reconstruction of the earthquake source mechanics, complementary to seismological investigations.129 760 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Static stress drop associated with brittle slip events on exhumed faults.
We estimate the static stress drop on small exhumed strike-slip faults in the Lake Edison granodiorite of the central Sierra Nevada (California). The subvertical strike-slip faults were exhumed from 4 to 15 km depth and were chosen because they are exposed in outcrop along their entire tip-to-tip lengths of 8–12 m. Slip nucleated on joints and accumulated by crystal-plastic shearing (forming quartz mylonites from early quartz vein filling in joints) and successive brittle faulting (forming epidote-bearing cataclasites). The occurrence of thin, 300 mm wide, pseudotachylytes along some small faults throughout the study area suggests that some, if not all, of the brittle slip on the study area faults may have been seismic. We suggest that the contribution of brittle, cataclastic slip to the total slip along the studied cataclasite-bearing small faults may be estimated by the length of epidote-filled, rhombohedral dilatational jogs (rhombochasms) distributed quasi-periodically along the length of the faults. The interpretation that slip recorded by rhombochasms occurred in single events is based on evidence that (1) epidote crystals are randomly oriented and undeformed within the rhombochasm; (2) cataclasite in principal slip zones does not include clasts of previous cataclasite, and (3) rhombochasm lengths vary systematically along the length of the faults with slip maximum occurring near the fault center, tapering to the fault tips. We thereby constrain both the rupture length and slip. On the basis of these measurements, we calculate stress drops ranging over 90–250 MPa, i.e., one to two orders of magnitude larger than typical seismological estimates for earthquakes, but similar in magnitude to seismological estimates of small (<M2) earthquakes from the San Andreas Fault Observatory at Depth (SAFOD). The slip events described in the present study occurred along small, deep-seated faults, and, given the calculated stress drops and observations that brittle faults exploited joints sealed by quartz-bearing mylonite, we conclude that these were ‘‘strong’’ faults.159 27 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Seismic tremor in subduction zones: the rock-physics evidence
(2009); ; ; ;Burlini, L.; ETH ZurichDi Toro, G.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, ItaliaEpisodic tremor and slip (ETS) have been correlated with rupture phenomena in subducting oceanic lithosphere at 30–45 km depth, where high VP/VS ratios, which suggest high-fluid pressures, have been observed. ETS, by accommodating slip in the down-dip portion of the subduction zone, may trigger megathrust earthquakes up-dip in the locked section. During dehydration experiments on serpentinite (typical rock of the oceanic lithosphere) at temperatures found in nature at 30–45 km depth (400– 550 C), we observe seismic signals in the form of acoustic emissions that closely resemble low frequency earthquakes, seismic tremor and regular earthquakes. Our findings support the concept that water released during dehydration reactions increases the pore pressures and can trigger ETS and regular earthquakes by reducing slip resistance. Citation: Burlini, L., G. Di Toro, and P. Meredith (2009), Seismic tremor in subduction zones: Rock physics evidence, Geophys. Res. Lett., 36, L08305, doi:10.1029/2009GL037735.152 22 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Energy partitioning during seismic slip in pseudotachylyte-bearing faults
(2008-02-19); ; ; ; The determination of the earthquake energy budget remains a challenging issue for Earth scientists, as understanding the partitioning of energy is a key towards the understanding the physics of earthquakes. Here we estimate the partition of the mechanical work density into heat and surface energy (energy required to create new fracture surface) during seismic slip on a location along a fault. Earthquake energy partitioning is determined from field and microstructural analyses of a fault segment decorated by pseudotachylyte (solidified friction-induced melt produced during seismic slip) exhumed from a depth of ~10 km—typical for earthquake hypocenters in the continental crust. Frictional heat per unit fault area estimated from the thickness of pseudotachylytes is ~27 MJ m−2. Surface energy, estimated from microcrack density inside clast (i.e., cracked grains) entrapped in the pseudotachylyte and in the fault wall rock, ranges between 0.10 and 0.85 MJ m−2. Our estimates for the studied fault segment suggest that ~97–99% of the energy was dissipated as heat during seismic slip. We conclude that at 10 km depth, less than 3% of the total mechanical work density is adsorbed as surface energy on the fault plane during earthquake rupture.148 25 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Recent advances in the understanding of fault zone internal structure: a review
(2008); ; ; ;Wibberley, C. A. J.; Géosciences Azur, CNRS UMR6526, Universite´ de Nice – Sophia Antipolis, 250 rueGraham, Y.; Badley Geoscience Ltd, North Beck House, North Beck Lane, Hundleby,It is increasingly apparent that faults are typically not discrete planes but zones of deformed rock with a complex internal structure and three-dimensional geometry. In the last decade this has led to renewed interest in the consequences of this complexity for modelling the impact of fault zones on fluid flow and mechanical behaviour of the Earth’s crust. A number of processes operate during the development of fault zones, both internally and in the surrounding host rock, which may encourage or inhibit continuing fault zone growth. The complexity of the evolution of a faulted system requires changes in the rheological properties of both the fault zone and the surrounding host rock volume, both of which impact on how the fault zone evolves with increasing displacement. Models of the permeability structure of fault zones emphasize the presence of two types of fault rock components: fractured conduits parallel to the fault and granular core zone barriers to flow. New data presented in this paper on porosity–permeability relationships of fault rocks during laboratory deformation tests support recently advancing concepts which have extended these models to show that poro-mechanical approaches (e.g., critical state soil mechanics, fracture dilatancy) may be applied to predict the fluid flow behaviour of complex fault zones during the active life of the fault. Predicting the three-dimensional heterogeneity of fault zone internal structure is important in the hydrocarbon industry for evaluating the retention capacity of faults in exploration contexts and the hydraulic behaviour in production contexts. Across-fault reservoir juxtaposition or non-juxtaposition, a key property in predicting retention or across-fault leakage, is strongly controlled by the three-dimensional complexity of the fault zone. Although algorithms such as shale gouge ratio greatly help predict capillary threshold pressures, quantification of the statistical variation in fault zone composition will allow estimations of uncertainty in fault retention capacity and hence prospect reserve estimations. Permeability structure in the fault zone is an important issue because bulk fluid flow rates through or along a fault zone are dependent on permeability variations, anisotropy and tortuosity of flow paths. A possible way forward is to compare numerical flow models using statistical variations of permeability in a complex fault zone in a given sandstone/shale context with field-scale estimates of fault zone permeability. Fault zone internal structure is equally important in understanding the seismogenic behaviour of faults. Both geometric and compositional complexities can control the nucleation, propagation and arrest of earthquakes. The presence and complex distribution of different fault zone materials of contrasting velocity-weakening and velocity-strengthening properties is an important factor in controlling earthquake nucleation and whether a fault slips seismogenically or creeps steadily, as illustrated by recent studies of the San Andreas Fault. A synthesis of laboratory experiments presented in this paper shows that fault zone materials which become stronger with increasing slip rate, typically then get weaker as slip rate continues to increase to seismogenic slip rates. Thus the probability that a nucleating rupture can propagate sufficiently to generate a large earthquake depends upon its success in propagating fast enough through these materials in order to give them the required velocity kick. This propagation success is hence controlled by the relative and absolute size distributions of velocity-weakening and velocity- strengthening rocks within the fault zone. Statistical characterisation of the distribution of such contrasting properties within complex fault zones may allow for better predictive models of rupture propagation in the future and provide an additional approach to earthquake size forecasting and early warnings.468 61 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Mantle earthquakes frozen in mylonitized ultramafic pseudotachylytes of spinel-lherzolite facies.
(2008); ; ; ; We report a new type of ultramafi c pseudotachylyte that forms a fault- and injection-vein network hosted in the mantle-derived Balmuccia peridotite (Italy). In the fault vein the pseudotachylyte is now deformed and recrystallized into a spinel-lherzolite facies ultramylonite, made of a fi ne (<2 μm) aggregate of olivine, orthopyroxene, clinopyroxene, and spinel, with small amounts of amphibole and dolomite. Electron backscattered diffraction study of the ultramylonite shows a clear crystallographic preferred orientation (CPO) of olivine. The fault vein pseudotachylyte overprints a spinel-lherzolite facies amphibole-bearing mylonite, indicating that shear localization accompanying chemical reaction had taken place in the peridotite before seismic slip produced frictional melting. The occurrence of amphibole in the host mylonite and that of dolomite as well as amphibole in the matrices of ultramylonite and pseudotachylyte may indicate that fl uid was present and had evolved in its composition from H2O-rich to CO2-rich during ductile deformation with metamorphic reactions, which may account for the observed rheological transition from ductile to brittle behavior. The spinel-lherzolite facies assemblage in mylonites, P-T estimations from pyroxene geothermometry and carbonate reactions, and the type of olivine CPO in deformed pseudotachylyte indicate that both the preseismic and the postseismic ductile deformations occurred at ~800 °C and 0.7–1.1 GPa.119 1320 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Frictional Melt and Seismic Slip
(2008-01); ; ; ; Nielsen, S.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, ItaliaFrictional melt is implied in a variety of processes such as seismic slip, ice skating,and meteorite combustion. A steady state can be reached when melt is continuously produced and extruded from the sliding interface, as shown recently in a number of laboratory rock friction experiments. A thin, low-viscosity, high-temperature melt layer is formed resulting in low shear resistance. A theoretical solution describing the coupling of shear heating, thermal diffusion, and extrusion is obtained, without imposing a priori the melt thickness. The steady state shear traction can be approximated at high slip rates by the theoretical form : tau=sn^[1/4] (A/sqrt[R]) sqrt[ log[2 V/W] / (V/W) ] under a normal stress sn, slip rate V, radius of contact area R (A is a dimensional normalizing factor and W is a characteristic rate). Although the model offers a rather simplified view of a complex process, the predictions are compatible with experimental observations. In particular, we consider laboratory simulations of seismic slip on earthquake faults. A series of highvelocity rotary shear experiments on rocks, performed for sn in the range 1–20 MPa and slip rates in the range 0.5–2 m/s, is confronted to the theoretical model. The behavior is reasonably well reproduced, though the effect of radiation loss taking place in the experiment somewhat alters the data. The scaling of friction with sn, R, and V in the presence of melt suggests that extrapolation of laboratory measures to real Earth is a highly nonlinear, nontrivial exercise.126 26 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Fault weakness during seismic slip
(2007-09-25); ; ;Di Toro, G.; Univ. Padua, Italy ;Nielsen, S.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, Italiasee Abstract Volume131 538
