Skip to main content
The search returned 24 results
Now showing 1 - 10 of 24
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Frictional properties of Opalinus Clay: influence of humidity, normal stress and grain size on frictional stability

    The Opalinus Clay (OPA) is a clay-rich formation considered as a potential host rock for radioactive waste repositories and as a caprock for carbon storage in Switzerland. Its very low permeability (10−19 to 10−21 m2) makes it a potential sealing horizon, however the presence of faults that may be activated during the lifetime of a repository project can compromise the long-term hydrological confinement, and lead to mechanical instability. Here, we have performed laboratory experiments to test the effect of relative humidity (RH), grain size (g.s.) and normal stress on rate-and-state frictional properties and stability of fault laboratory analogues corresponding to powders of OPA shaly facies. The sifted host rock powders at different grain size fractions (<63 μm and 63 < g.s. < 125 μm), at room (∼25 per cent) and 100 per cent humidity, were slid in double-direct shear configuration, under different normal stresses (5–70 MPa). We observe that peak friction, μpeak and steady-state friction, μss, depend on water vapour content and applied normal stress. Increasing relative humidity from ∼25 per cent RH (room humidity) to 100 per cent RH causes a decrease of frictional coefficient from 0.41 to 0.35. The analysis of velocity-steps in the light of rate-and-state friction framework shows that the stability parameter (a–b) is always positive (velocity-strengthening), and it increases with increasing sliding velocity and humidity. The dependence of (a–b) on slip rate is lost as normal stress increases, for each humidity condition. By monitoring the variations of the layer thickness during the velocity steps, we observe that dilation (Δh) is directly proportional to the sliding velocity, decreases with normal stress and is unaffected by humidity. Microstructural analysis shows that most of the deformation is accommodated within B-shear zones, and the increase of normal stress (σn) promotes the transition from strain localization and grain size reduction to distributed deformation on a well-developed phyllosilicate network. These results suggest that: (1) the progressive loss of velocity dependence of frictional stability parameter (a–b) at σn > 35 MPa is dictated by a transition from localized to distributed deformation and (2) water vapour content does not affect the deformation mechanisms and dilation, whereas it decreases steady-state friction (μss), and enhances fault stability.
      38  81
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Fabric controls fault stability in serpentinite gouges

    Serpentinites are polymineralic rocks distributed almost ubiquitously across the globe in active tectonic regions. Magnetite-rich serpentinites are found in the low-strain domains of serpen- tinite shear zones, which act as potential sites of nucleation of unstable slip. To assess the potential of earthquake nucleation in these materials, we investigate the link between me- chanical properties and fabric of these rocks through a suite of laboratory shear experiments. Our experiments were done at room temperature and cover a range of normal stress and slip velocity from 25 to 100 MPa and 0.3 to 300 μm s −1 , respecti vel y. We show that magnetite-rich serpentinites are ideal materials since they display strong sensitivity to the loading rate and are susceptible to nucleation of unstable slip, especially at low forcing slip velocities. We also aim at the integration of mechanical and microstructural results to describe the underlying mechanisms that produce the macroscopic behaviour. We show that mineralogical composi- tion and mineral structure dictates the coexistence of two deformation mechanisms leading to stable and unstable slip. The weakness of phyllosilicates allows for creep during the interseis- mic phase of the laboratory seismic cycle while favouring the restoration of a load-bearing granular framework, responsible of the nucleation of unstable events. During dynamic slip, fault zone shear fabric determines the mode of slip, producing either asymmetric or Gaussian slip time functions for either fast or slow events. We report rate/state friction parameters and integrate our mechanical data with microstructural observations to shed light on the mech- anisms dictating the complexity of laborator y ear thquakes. We show that mineralogical and fabric heterogeneities control fault slip behaviour.
      82  85
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Rheological heterogeneities at the roots of the seismogenic zone

    Although rheological heterogeneities are invoked to explain differences in fault-slip be- havior, case studies where an interdisciplinary approach is adopted to capture their specific roles are still rare. In this work, we integrated geophysical, geological, and laboratory data to explain how rheological heterogeneities influence the earthquake activity at the roots of the seismogenic zone. During the 2016–2017 Central Italy sequence, following the major earthquakes, we observed a deepening of seismicity within the basement associated with a transient stress change. Part of this seismicity was organized in clusters of events, with similar sizes and waveforms. The structural study of exhumed basement rocks highlighted a heterogeneous fabric made of strong, quartz-rich lenses (up to 200 m) surrounded by a weak, interconnected phyllosilicate-rich matrix. Laboratory experiments simulating the main shock–induced increase in loading rate showed that the matrix lithology experienced an ac- celerating and self-decelerating aseismic creep, whereas the lens lithology showed dynamic instabilities. Our results suggest that the post–main shock loading rate increases favored accelerated creep within the matrix, which promoted, as a consequence, seismic instabilities within the lenses in the form of clustered seismicity. Our findings emphasize the strong con- nection between seismicity and the structural and frictional properties of the seismogenic zone.
      32  40
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    The Role of Fault Rock Fabric in the Dynamics of Laboratory Faults

    Fault stability is inherently linked to the frictional and healing properties of fault rocks and associated fabrics. Their complex interaction controls how the stored elastic energy is dissipated, that is, through creep or seismic motion. In this work, we focus on the relevance of fault fabrics in controlling the reactivation and slip behavior of dolomite-anhydrite analog faults. We designed a set of laboratory experiments where we first develop fault rocks characterized by different grain size reduction and localization at normal stresses of σN = 15, 35, 60, and 100 MPa and second, we reload and reactivate these fault rocks at the frictional stability transition, achieved at σN = 35 MPa by reducing the machine stiffness. If normal stress is lowered this way, reactivation occurs with relatively large stress drops and large peak-slip velocities. Subsequent unstable behavior produces slow stick-slip events with low stress drop and with either asymmetric or Gaussian slip velocity function depending on the inherited fault fabric. If normal stress is raised, deformation is accommodated within angular cataclasites promoting stable slip. The integration of microstructural data (showing brittle reworking of preexisting textures) with mechanical data (documenting restrengthening and dilation upon reactivation) suggests that frictional and chemically assisted healing, which is common in natural faults during the interseismic phase, can be a relevant process in developing large instabilities. We also conclude that fault rock heterogeneity (fault fabric) modulates the slip velocity function and thus the dynamics of repeating stick-slip cycles.
      33  178
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Frictional controls on the seismogenic zone: Insights from the Apenninic basement, Central Italy

    Crustal seismicity is in general confined within the seismogenic layer, which is bounded at depth by processes related to the brittle-ductile transition (BDT) and in the shallow region by fault zone consolidation state and mineralogy. In the past 10-15 years, high resolution seismological and geodetic data have shown that faulting within and around the traditional seismogenic zone occurs in a large variety of slip modes. Frictional and structural heterogeneities have been invoked to explain such differences in fault slip mode and behaviour. However, an integrated and comprehensive picture remains extremely challenging because of difficulties to properly characterize fault rocks at seismogenic depths. Thus, the central-northern Apennines provide a unique opportunity because of the integration of deep-borehole stratigraphy and seismic reflection profiles with high resolution seismological data and outcrop studies. These works show that seismic sequences are limited within the sedimentary cover (depth < 9-10 km), suggesting that the underlaying basement plays a key-role in dictating the lower boundary of the seismogenic zone. Here we integrate structural data on exhumed outcrops of basement rocks with laboratory friction data to shed light on the mechanics of the Apenninic basement. Structural data highlight heterogeneous and pervasive deformation where foliated and phyllosilicate-rich rocks surround more competent quartz-rich lenses up to hundreds of meters in thickness. Phyllosilicate horizons deform predominantly by folding and foliation-parallel frictional sliding whereas quartz-rich lenses are characterized by brittle signatures represented by extensive fracturing and minor faulting. Laboratory experiments revealed that quartz-rich lithologies have relatively high friction, μ ≈ 0.51, velocity-strengthening to neutral behaviour, and elevated healing rates. On the contrary, phyllosilicate-rich (muscovite and chlorite) lithologies show low friction, 0.23 < μ < 0.31, a marked velocity strengthening behaviour that increases with increasing sliding velocity and negligible rates of frictional healing. Our integrated approach suggests that in the Apenninic basement deformation occurs along shear zones distributed on thickness up-to several kilometres, where the frictionally stable, foliated, and phyllosilicate-rich horizons favour aseismic deformation and therefore confine the depth of major earthquake ruptures and the seismogenic zone.
      72  114
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    The Role of Fabric in Frictional Properties of Phyllosilicate-Rich Tectonic Faults

    Many rock deformation experiments used to characterize the frictional properties of tectonic faults are performed on powdered fault rocks or on bare rock surfaces. These experiments have been fundamental to document the frictional properties of granular mineral phases and provide evidence for crustal faults characterized by high friction. However, they cannot entirely capture the frictional properties of faults rich in phyllosilicates. Numerous studies of natural faults have documented fluid-assisted reaction softening promoting the replacement of strong minerals with phyllosilicates that are distributed into continuous foliations. To study how these foliated fabrics influence the frictional properties of faults we have: 1) collected foliated phyllosilicate-rich rocks from natural faults; 2) cut the fault rock samples to obtain solid wafers 0.8-1.2 cm thick and 5 cm x 5 cm in area with the foliation parallel to the 5x5cm face of the wafer; 3) performed friction tests on both solid wafers sheared in their in situ geometry and powders, obtained by crushing and sieving and therefore disrupting the foliation of the same samples; 4) recovered the samples for microstructural studies from the post experiment rock samples; and 5) performed microstructural analyses via optical microscopy, scanning and transmission electron microscopy. Mechanical data show that the solid samples with well-developed foliation show significantly lower friction in comparison to their powdered equivalents. Micro- and nano-structural studies demonstrate that low friction results from sliding along the foliation surfaces composed of phyllosilicates. When the same rocks are powdered, frictional strength is high, because sliding is accommodated by fracturing, grain rotation, translation and associated dilation. Friction tests indicate that foliated fault rocks may have low friction even when phyllosilicates constitute only a small percentage of the total rock volume, implying that a significant number of crustal faults are weak.
      67  148
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Frictional properties of basalt experimental faults and implications for volcano-tectonic settings and geo-energy sites

    We performed a suite of experiments aimed at examining the frictional properties of unaltered basalts at conditions considered to be representative of slip at shallow depths in volcano-tectonic environments and in-situ geo-energy basaltic sites. Scientific drilling and field studies on exhumed subsurface faults and fractures analogues suggest that, frictional sliding in basalts can occur in shear zones within a volume of wear debris or along localized joint surfaces. To illuminate how microstructural heterogeneities affect the nucleation of slip instabilities in basalts, we sheared simulated fault gouge and bare rock surfaces at low normal stresses (4–30 MPa) at ambient temperature, under room-dry and wet conditions. We performed velocity steps (0.1–300 μm/s) and slide-hold-slides (30–3000 s holds) to determine the frictional stability and healing properties of basalts. In all the tests, we observed high friction coefficient associated with important frictional restrengthening. Overall, our results show that microstructural heterogeneities strongly affect the friction velocity dependence of basalts: while for normal stresses ≥10 MPa, shear localization accompanied by cataclasis and grain size reduction favors the transition to velocity weakening behavior of powdered samples, on bare surfaces gouge production during shearing promotes a transition to a velocity strengthening behavior. Our results imply that at the tested conditions, friction instabilities may promptly nucleate in shear zones where deformation within (unaltered) basaltic gouge layers is localized, such as those located along volcanic flanks, while joint surfaces characterized by rough rock-on-rock contacts are less prone to unstable slip, which is suppressed at velocities ≥10 μm/s.
      66  212
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    The role of shale content and pore-water saturation on frictional properties of simulated carbonate faults

    The presence of weak phyllosilicates in mature carbonate fault zones has been invoked to explain weak faults. However, the relation between frictional strength, fault stability, mineralogical composition, and fabric of fault gouge, composed of strong and weak minerals, is poorly constrained. We used a biaxial apparatus to systematically shear different mixtures of shale (68% clay, 23% quartz and 4% plagioclase) and calcite, as powdered gouge, at room temperature, under constant normal stresses of 30, 50, 100 MPa and under room-dry and pore fluid-saturated conditions, i.e. CaCO3-equilibrated water. We performed 30 friction experiments during which velocity-stepping and slide-hold-slide tests were employed to assess frictional stability and to measure frictional healing, respectively. Our frictional data indicate that the mineralogical composition of fault gouges significantly affects frictional strength, stability, and healing as well as the presence of CaCO3-equilibrated water. Under room-dry condition, the increasing shale content determines a reduction in frictional strength, from μ = 0.71 to μ = 0.43, a lowering of the healing rates and a transition from velocity-weakening to velocity-strengthening behavior. Under wet condition, with increasing shale content we observe a more significant reduction in frictional strength (μ = 0.65–0.37), a near-zero healing and a velocity strengthening behavior. Microstructural investigations evidence a transition from localized deformation promoted by grain size reduction, in calcite-rich samples, to a more distributed deformation with frictional sliding along clay-enriched shear planes in samples with shale content greater than 50%. For faults cutting across sedimentary sequences composed of carbonates and clay-rich sediments, our results suggest that clay concentration and its ability to form foliated and interconnected networks promotes important heterogeneities in fault strength and slip behavior.
      51  2
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Bifurcations at the Stability Transition of Earthquake Faulting

    Tectonic faults typically break in a single rupture mode within the range of styles from slow slip to dynamic earthquake failure. However, in increasingly well‐documented instances, the same fault segment fails in both slow and fast modes within a short period, as in the sequences that culminated in the 2011 Mw = 9.0 Tohoku‐Oki, Japan, and 2014 Mw = 8.2 Iquique, Chile, earthquakes. Why slow slip alternates with dynamic rupture in certain regions but not in others is not well understood. Here, we integrate laboratory experiments and numerical simulations to investigate the physical conditions leading to cycles where the two rupture styles alternate. We show that a bifurcation takes place near the stability transition with sequences encompassing various rupture modes under constant loading rate. The range of frictional instabilities and slip cycles identified in this study represents important end‐members to understand the interaction of slow and fast slip on the same fault segment.
      68  92
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Frictional Strengthening Explored During Non‐Steady State Shearing: Implications for Fault Stability and Slip Event Recurrence Time

    On natural faults that host repeating slip events, the inter‐event loading time is quite large compared to the slip event duration. Since most friction studies focus on steady‐state frictional behavior, the fault loading phase is not typically examined. Here, we employ a method specifically designed to evaluate fault strength evolution during active loading, under shear driving rates as low as 10−10 m/s, on natural fault gouge samples from the Waikukupa Thrust in southern New Zealand. These tests reveal that in the early stages of loading following a slip event, there is a period of increased stability, which fades with accumulated slip. In the framework of rate‐ and state‐dependent friction laws, this temporary stable phase exists as long as slip is less than the critical slip distance and the elapsed time is less than the value of the state variable at steady state. These observations indicate a minimum earthquake recurrence time, which depends on the field value of the critical slip distance and the background slip rate. We compare estimates of minimum earthquake recurrence times with the recurrence times of repeating large earthquakes on the Alpine Fault in southern New Zealand and repeating small‐magnitude earthquakes on the San Andreas Fault system in California. We find that the observed recurrence times are mostly longer than the predicted minimum values, and exceptions in the San Andreas system may be explained by elevated slip rates due to larger earthquakes in this region.
      62  98