Skip to main content
The search returned 3 results
Now showing 1 - 3 of 3
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Frictional properties of basalt experimental faults and implications for volcano-tectonic settings and geo-energy sites

    We performed a suite of experiments aimed at examining the frictional properties of unaltered basalts at conditions considered to be representative of slip at shallow depths in volcano-tectonic environments and in-situ geo-energy basaltic sites. Scientific drilling and field studies on exhumed subsurface faults and fractures analogues suggest that, frictional sliding in basalts can occur in shear zones within a volume of wear debris or along localized joint surfaces. To illuminate how microstructural heterogeneities affect the nucleation of slip instabilities in basalts, we sheared simulated fault gouge and bare rock surfaces at low normal stresses (4–30 MPa) at ambient temperature, under room-dry and wet conditions. We performed velocity steps (0.1–300 μm/s) and slide-hold-slides (30–3000 s holds) to determine the frictional stability and healing properties of basalts. In all the tests, we observed high friction coefficient associated with important frictional restrengthening. Overall, our results show that microstructural heterogeneities strongly affect the friction velocity dependence of basalts: while for normal stresses ≥10 MPa, shear localization accompanied by cataclasis and grain size reduction favors the transition to velocity weakening behavior of powdered samples, on bare surfaces gouge production during shearing promotes a transition to a velocity strengthening behavior. Our results imply that at the tested conditions, friction instabilities may promptly nucleate in shear zones where deformation within (unaltered) basaltic gouge layers is localized, such as those located along volcanic flanks, while joint surfaces characterized by rough rock-on-rock contacts are less prone to unstable slip, which is suppressed at velocities ≥10 μm/s.
      66  212
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Basin modeling constrains source rock position and dimension in the Burano-Bolognano petroleum system (Central Italy)

    A two-dimensional basin and petroleum system modeling approach was applied to the Burano-Bolognano petroleum system (Central Italy) to constrain some factors (position, lateral extension and maturity of the source rock, the role of fractures and faults in hydrocarbon migration) which influenced its structural evolution and the related migration pathways. The petroleum system extends from the Majella Mountain to the northern Cigno, Vallecupa, Bonanno oil fields, intensively explored during the past century. Some features, such as the location and extension of the source rock and its maturity, and hydrocarbon pathways, are still undefined. Thus, we developed a 3D geological static model of the Cenozoic carbonate succession and then, we performed basin modeling along a 2D geological section, integrating the petrophysical properties of rocks measured in laboratory. Our results prove that the Burano source rock reached a low-middle maturity, and the best representation of the actual hydrocarbon occurrences is reached when the source rock is at north of the Majella Mountain with a minimum extension of 3 km. For the BBPS a strong lateral migration and a gradual oil biodegradation towards the Majella area must be considered. Moreover, modeling results highlight a minor control of the faults on the migration in this area. This basin modeling is relevance for investigations in similar settings since carbonate-ramp reservoir studies are usually very challenging to be correctly modeled due to their high heterogeneities.
      58  139
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    The role of shale content and pore-water saturation on frictional properties of simulated carbonate faults

    The presence of weak phyllosilicates in mature carbonate fault zones has been invoked to explain weak faults. However, the relation between frictional strength, fault stability, mineralogical composition, and fabric of fault gouge, composed of strong and weak minerals, is poorly constrained. We used a biaxial apparatus to systematically shear different mixtures of shale (68% clay, 23% quartz and 4% plagioclase) and calcite, as powdered gouge, at room temperature, under constant normal stresses of 30, 50, 100 MPa and under room-dry and pore fluid-saturated conditions, i.e. CaCO3-equilibrated water. We performed 30 friction experiments during which velocity-stepping and slide-hold-slide tests were employed to assess frictional stability and to measure frictional healing, respectively. Our frictional data indicate that the mineralogical composition of fault gouges significantly affects frictional strength, stability, and healing as well as the presence of CaCO3-equilibrated water. Under room-dry condition, the increasing shale content determines a reduction in frictional strength, from μ = 0.71 to μ = 0.43, a lowering of the healing rates and a transition from velocity-weakening to velocity-strengthening behavior. Under wet condition, with increasing shale content we observe a more significant reduction in frictional strength (μ = 0.65–0.37), a near-zero healing and a velocity strengthening behavior. Microstructural investigations evidence a transition from localized deformation promoted by grain size reduction, in calcite-rich samples, to a more distributed deformation with frictional sliding along clay-enriched shear planes in samples with shale content greater than 50%. For faults cutting across sedimentary sequences composed of carbonates and clay-rich sediments, our results suggest that clay concentration and its ability to form foliated and interconnected networks promotes important heterogeneities in fault strength and slip behavior.
      51  2