Skip to main content
The search returned 15 results
Now showing 1 - 10 of 15
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Characterizing the subsurface structure and active faults of the Fucino Basin (Central Apennines) through integrated high-resolution seismic reflection and nodal ambient noise surveys

    (Lausann : Frontiers Media S.A., 2013-, 2026-03-24) ; ; ; ;
    The Fucino Basin, the largest tectonic basin within the Central Apennines orogen, is bounded by normal faults that have controlled the deposition of over 1 km of Pliocene-Quaternary continental deposits above a Messinian substratum. Conflicting interpretations from legacy seismic profiles have hindered a full understanding of the basin’s stratigraphy, age, evolution, and fault systems, creating uncertainties for tectonic reconstructions, seismic response analysis and hazard assessment. To resolve these uncertainties, we acquired new high-resolution datasets through three complementary active–passive seismic surveys. These include seismic reflection profiles covering ∼10 km, a nodal ambient noise campaign deploying 258 short-period nodes over 16 km2, preceded by two pilot array tests, and finally a basin-wide ambient noise survey comprising 1-hour recordings at 42 sites. Our analysis focused on the San Benedetto and Trasacco Faults—responsible for the 1915, M7.1, Marsica earthquake—and the main depocenter (the Bacinetto) associated with the San Benedetto Fault. This paper presents experimental setup, recorded data, and initial findings that provide new insights into basin stratigraphy, fault geometry, and spatial distribution of the fundamental resonance frequency (f0). The seismic reflection data show excellent imaging quality, resolution, and penetration exceeding 1 km. The Bacinetto hosts up to 850–900 m of continuous lacustrine succession and lower fluvio-lacustrine deposits that record sustained syn-sedimentary slip along the San Benedetto Fault from the Late Pliocene to Recent times. No evidence is found for significant synthetic or antithetic faulting beneath the depocenter, contradicting earlier structural models. The intra-basin Trasacco Fault forms a clear basement step and localized sediment thickening that tapers northwestward f0 varies from 1 to 2 Hz near the basin margins to ∼0.2 Hz in the Bacinetto, reflecting progressive sediment thickening, whereas it varies abruptly across fault zones. f0 estimates from nodal and station data show good consistency.
      19  17
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Urban Seismic Network Based on MEMS Sensors: The Experience of the Seismic Observatory in Camerino (Marche, Italy)

    Urban seismic networks are considered very useful tools for the management of seismic emergencies. In this work, a study of the first urban seismic network in central Italy is presented. The urban seismic network, built using MEMS sensors, was implemented in the urban district of Camerino, one of the cities in central Italy with the greatest seismic vulnerability. The technological choices adopted in developing this system as well as the implemented algorithms are shown in the context of their application to the first seismic event recorded by this innovative monitoring infrastructure. This monitoring network is innovative because it implements a distributed computing and statistical earthquake detection algorithm. As such, it is not based on the traces received by the stations from the central server; rather, each station carries out the necessary checks on the signal in real time, sending brief reports to the server in case of anomalies. This approach attempts to shorten the time between event detection and alert, effectively removing the dead times in the systems currently used in the Italian national network. The only limit for an instant alarm is the latency in the tcp/ip packages used to send the short reports to the server. The presented work shows the infrastructure created; however, there is not enough data to draw conclusions on this new early warning approach in the field, as it is currently in the data collection phase.
      293  157
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Sullo sviluppo della rete multiparametrica in Sicilia

    This contribution illustrates the state of the art on the development of the multiparametric network in Sicily in the last three years. This region is wellknown for the strong earthquakes (M>6.5) which struck in historic time. However, the coverage of the seismic network developed in the last decades was not fully optimized to the need of the seismic surveillance. Since 2017, the group belonging to the National Earthquake Observatory (ONT) which operates in Sicily launched a developing plan of the preexisting seismic network in the framework of the project FISR “Sale Operative Integrate e Reti di Monitoraggio del futuro: l’INGV 2.0 (S.O.I.R.)”. Such update will end by the next years thanks to the project “GRINT Italian Research Infrastructure for Geosciences” in the framework of the “Programma Operativo Nazionale” (PON) of the Italian Ministry for the University and Research. This plan envisages both the upgrade of monitoring systems in the already existing nodes, and the integration of new nodes. The main objective is to build a multiparametric network which integrates the main seismic network, with the monitoring of other geophysical signals through the implementation of other sensors: accelerometers, geodetic GPS, radon detectors, and corner reflectors. We also illustrate the plan for the realization of a redundant network which could support the tasks of the main infrastructure in case of failure of the latter. Finally, we present some experimental urbanscale networks which in the future could support the main infrastructure.
      719  36
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Sviluppo di una stazione sismica low-cost basata su tecnologia MEMS

    The impact of a strong earthqauke onto an urban community can be reduced taking timely actions managed by the authority in charge for the civil protection. In this view, it is of fundamental importance that the authority in charge for the seismic surveillance is provided with the appropriate monitoring tools able to give the most useful information for the best emergency management in the immediate postevent. Today this goal can be reached realizing urbanscale, realtime seismic monitoring networks (Osservatori Sismici Urbani, OSU, in Italian). The realtime OSU networks are able to promptly provide information to the emergency authority about the ground shaking at each node after an earthquake. Maps showing the spatial distribution of the ground shaking could help in the optimization of the priorities and a good management of the rescue resources in order to reduce the number of victims. Also the assessment of the damage of the buildings could be carried out according to the logic of priority given by the shakings measured by the OSU. The realisation of OSUs is the main objective of the MEMS project. This project is funded by the MIUR under the SIR program (Scientific Independence of young Researchers). The first challenge of the MEMS project was the design and the development of a devoted accelerometric stations. This work illustrates in detail the accelerometric station based on MEMS technology (Micro ElectroMechanical Systems). The final product is a lowcost accelerometric station with high performance and great versatility.
      931  43
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Real-time urban seismic network and structural monitoring by means of accelerometric sensors: Application to the historic buildings of Catania (Italy)

    A real-time urban seismic network for seismic and structural health monitoring is being installed in the city of Catania (Sicily, Italy). The 27 monitoring stations, specifically designed and assembled, equipped with a low-noise 3-axial MEMS accelerometer, are located in 23 high exposure and vulnerability buildings. In this paper we present the characteristics of the monitoring station and of the network. In case of strong seismic events, the system will provide shake maps to the emergency management centre, and will allow to assess the health conditions of the monitored buildings. The network is conceived to be further expandable over the whole historical city centre of the city of Catania.
      115  3
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Monitoring Earthquake through MEMS Sensors (MEMS project) in the town of Acireale (Italy)

    We introduce the realization of the first European real-time urban seismic network based on Micro ElectroMechanical Systems (MEMS) technology. The project is called Monitoring Earthquake through MEMS Sensors (MEMS) and encompass the installation of about 100 seismic station in the municipality of Acireale (Sicily, Italy). The stations, specifically designed and assembled, are equipped with a triaxial MEMS accelerometer, and gyroscope and GPS. In this paper we present the characteristics of the station and of the network. The main objective of the network is a rapid, post-earthquake disaster assessment through the automatic production of shake maps. The network also allow the implementation of an automatic recognition system for damage assessment from remotely piloted aircraft, and of a site-specific Earthquake Early Warning system.
      77  9
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    The marine activities performed within the TOMO-ETNA experiment

    The TOMO-ETNA experiment was planned in order to obtain a detailed geological and structural model of the continental and oceanic crust beneath Mt. Etna volcano and northeastern Sicily up to the Aeolian Islands (southern Italy), by integrating data from active and passive refraction and reflection seismic methodologies, magnetic and gravity surveys. This paper focuses on the marine activities performed within the experiment, which have been carried out in the Ionian and Tyrrhenian Seas, during three multidisciplinary oceanographic cruises, involving three research vessels (“Sarmiento de Gamboa”, “Galatea” and “Aegaeo”) belonging to different countries and institutions. During the offshore surveys about 9700 air-gun shots were produced to achieve a high-resolution seismic tomography through the wide-angle seismic refraction method, covering a total of nearly 2650 km of shooting tracks. To register ground motion, 27 ocean bottom seismometers were deployed, extending the inland seismic permanent network of the Istituto Nazionale di Geofisica e Vulcanologia (INGV) and a temporary network installed for the experiment. A total of 1410 km of multi-channel seismic reflection profiles were acquired to image the subsurface of the area and to achieve a 2D velocity model for each profile. Multibeam sonar and sub bottom profiler data were also collected. Moreover, a total of 2020 km of magnetic and 680 km of gravity track lines were acquired to compile magnetic and gravity anomaly maps offshore Mt. Etna volcano. Here, high-resolution images of the seafloor, as well as sediment and rock samples, were also collected using a remotely operated vehicle.
      1041  361
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    “Messina 1908-2008”: Progetto di ricerca integrato per l’area Calabro - Peloritana. L’esperimento di sismica passiva

    Il 28 dicembre 1908 un forte terremoto colpì duramente le città di Messina e di Regg io Calabria e molteplici centri abitati limitrofi. L’evento sismico di Mw=7.1 generò un maremoto e causò circa 100.000 morti. Durante il 2008 numerose sono state le iniziative per rievocare tale importante terremoto che è ricordato nella storia come il più forte avvenuto in Italia. Tra le iniziative promosse dall’Istituto Nazionale di Geofisica e Vulcanologia vi è il progetto di ricerca “Messina 1908-2008” le cui finalità sono far convergere i dati sismici e geodetici g ià a disposizione dei singoli gruppi di ricerca in un’unica banca dati e nel contempo promuoverne l’acquisizione di nuovi. In questo rapporto è descritto l’esperimento di sismica passiva integrato mare-terra iniziato ad ottobre 2007 e ter minato nel gennaio 2010 avente l’obiettivo di acquisire nuovi dati di alta qualità e dettaglio per ottenere una migliore definizione della microsismicità locale. Ciò consentirà di raggiungere una migliore comprensione di come inter ag iscano il processo di subduzione e le dinamiche superficiali nell’area dell’arco Calabro Peloritano ed in particolare nello stretto di Messina.
      444  327
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Report on the gravimetric, magnetometric, bathymetric activities during Cruise PANSTR10 with R/V Urania: Panarea and Stromboli, Aeolian Islands, 2010-02-05 - 2010-02-15.

    We present the shipboard activities and preliminary results of Cruise PANSTR10((2010-02-05 2010-02-15)) with R/V Urania. The cruise was scheduled to acquire high resolution magnetometric and gravimetric data on the Panarea and Stromboli volcanic edifices. In addition to this, swath bathymetry and CTD casts were obtained, and five OBS were launched N of Alicudi and on the lineament Stromboli-Marsili, aiming at collecting active and passive seismological data in the Aeolian and Calabrian Arcs.
      305  63
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    PROGETTO “MESSINA 1908 – 2008”. RAPPORTO DELLA CAMPAGNA OBS NELL’AREA EOLIANA E DELLO STRETTO DI MESSINA

    Il Centro Nazionale Terremoti (CNT), in collaborazione con la sezione di Catania, ha progettato e realizzato un esperimento di sismica passiva nell’area Calabro–Peloritana il cui scopo è fornire nuovi dati sismici volti a comprendere come le dinamiche superficiali ed il processo di subduzione interagiscano tra loro, migliorando così la comprensione dei processi sismogenetici nella zona colpita dal terremoto del 1908 [Margheriti et al., 2008; http://dpc-s5.rm.ingv.it]. Con l’obiettivo di ridurre l’errore di localizzazione degli ipocentri degli eventi verificatisi nell’area interessata dal progetto, ad integrazione delle 30 stazioni della rete sismica nazionale già presenti nell’area in esame, l’esperimento ha previsto l’installazione di 15 stazioni della rete mobile e la deposizione di 5 OBS/H (Ocean Bottom Seismometer with Hydrophone), per un numero complessivo di 50 stazioni sismiche larga banda 3C coinvolte nel progetto. La campagna sismica a terra ha avuto inizio nell’ottobre 2007 e ad oggi (gennaio 2009), le stazioni sono ancora in funzione, mentre la deposizione dei cinque OBS/H è avvenuta tra il 15 e il 18 luglio 2008 ed il loro recupero è stato effettuato tra il 6 e il 7 novembre 2008. Gli OBS/H, progettati e realizzati presso l’OBS Lab di Gibilmanna, sono stati equipaggiati con sismometri Nanometrics Trillium 120p (120s - 175 Hz) e con sensori differenziali di pressione (Differential Pressure Gauge) Cox-Webb, con banda passante tra i 200s e i 2Hz. La base autolivellante sulla quale è installato il sensore sismico è stata realizzata anch’essa presso l’OBS Lab di Gibilmanna nei mesi intercorsi tra il recupero degli OBS impiegati nella prima campagna NERIES, avvenuto nel marzo 2008, e il luglio 2008, data della deposizione degli OBS del progetto “Messina 1908 – 2008”. La necessità di realizzare una nuova base autolivellante in tempi così brevi, è stata una diretta conseguenza dei risultati negativi ottenuti dalla base Nautilus in occasione della già citata campagna NERIES [D’Anna et al., 2008]: due sismometri su tre non si erano livellati nel range di ±0.2°, massimo tilt dinamico previsto per i Trillium 120p, provocando il non funzionamento degli stessi. Come meglio verrà analizzato nei paragrafi successivi, le problematiche affrontate nella realizzazione di questi dispositivi di livellamento sono state molteplici e di difficile soluzione. L’analisi preliminare dei dati ha evidenziato che soltanto uno dei cinque sensori sismici ha funzionato correttamente per l’intero periodo, mentre gli altri quattro hanno funzionato in media per circa 20 giorni. Causa di ciò, un rapido consumo delle batterie dovuto ad un livellamento sì compreso nel range di ±0.2° dall’orizzontale, condizione necessaria perché il sismometro sia in grado di rilevare eventi sismici, ma oltre il range di ±0.1°, condizione necessaria perché i consumi del Trillium120p si riducano da circa 2.5W ai 600mW nominali. I risultati ottenuti da questo esperimento, sono comunque da inquadrare in una successione degli eventi che ha fatto sì che lo sviluppo di questa nuova base autolivellante fosse condizionato da una certa urgenza: al CNT premeva presentare i dati raccolti dagli OBS al convegno “Scienza e società a 100 anni dal grande Terremoto”, che si sarebbe tenuto a Reggio Calabria dal 10 al 12 dicembre 2008 e visti gli insuccessi della base Nautilus nel precedente esperimento, ci si è trovati di fronte alla necessità di progettare e sviluppare un nuovo sistema di livellamento per i Trillium 120p nell’arco di tre mesi e mezzo. Queste, oltre a quelle di natura economica, le ragioni per cui non è stato possibile procedere secondo un iter che per noi, come per le aziende che operano nel settore marino, è uno standard: - Progettazione; - Realizzazione del prototipo; - Test in laboratorio (e. g. tavola vibrante) - Test in camera iperbarica; - Test in mare; - Produzione in serie; E’ nostra intenzione, in un prossimo futuro, portare avanti lo sviluppo di questa base autolivellante, con tempi e risorse finanziare ed umane più appropriate. Ciò che riportiamo in questo Rapporto Tecnico vuole essere una descrizione del lavoro sin qui svolto, anche se non conclusivo e risolutivo, ma che ci ha già permesso di individuare delle problematiche fondamentali la cui soluzione sarà oggetto di studi più approfonditi. Rimane positivo il fatto che le basi già realizzate riescono già da adesso a livellare automaticamente un sensore entro un range di ±0.2°. Gli OBS/H dell’INGV verranno nuovamente deposti con la stessa disposizione del progetto “Messina 1908 – 2008” nell’estate 2009, nell’ambito del progetto S5 finanziato dal Dipartimento della Protezione Civile. Per sopperire alle problematiche riscontrate nella marinizzazione del Trillium 120p, si è scelto di installare a bordo degli OBS dei sensori Guralp CMG40T-OBS (60s – 100 Hz), progettati per installazioni in mare sino a profondità di 6000 m è già dotati di una propria base autolivellante. Il motivo per il quale non si è utilizzato nelle passate campagne questo tipo di sensore è da addebitare unicamente al fatto che sui fondi DPC della convenzione 2005-2007 non è stato possibile inserire l’acquisto di questi specifici sensori, mentre erano disponibili i Trillium 120p.
      213  537