Skip to main content
The search returned 179 results
Now showing 1 - 10 of 179
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    COMPARING 1D/3D GROUND MOTION SIMULATIONS FOR EARTHQUAKES IN CENTRAL ITALY

    The seismic activity known as the Amatrice-Visso-Norcia seismic sequence began on August 24th, 2016, with the M6.2 earthquake in Amatrice, Italy. This sequence included eight additional earthquakes with magnitudes above 5.0, which caused significant damage to nearby villages. The largest and most significant event occurred on October 30th, 2016, with a magnitude of 6.5 in Norcia, central Apennines. In this study, we perform physics-based simulations and investigate the ground motion variability for Norcia and Amatrice earthquakes using the Pitarka et al. (2021a) and Akinci et al. (2023) simulation approaches, respectively. We generated broad-band ground-motion acceleration time histories (0-10Hz) for these two earthquakes using frequency-wavenumber Green’s functions (FK approach) and kinematic rupture models generated with the Graves and Pitarka (2016) technique. The FK Green’s functions (GF) were computed using the propagator matrix method of Zhu and Rivera (2002) and a 1D velocity model of Central Italy (CIA) (Hermann et al., 2011). The FK-based broad-band simulation method allows for fast and realistic generation of synthetic time histories, provided that appropriate GF repository and source rupture models are available. Finally, we analyzed the performance of our 1D simulation approach by comparing our synthetic ground motions with those computed with a regional 3D velocity model and the recorded ones. We found that the FK-based simulation approach and the 1D CIA velocity model produce ground motion that compares well with recorded data throughout the region in the modeled frequency range 0-10 Hz. Because this simulation technique is very fast and reliable, it can be used to produce ground motion maps soon after a major earthquake, and in computing scenario-based ground motion for seismic hazard assessment in Central Italy.
      62  181
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    PAPER VOLCANOES LAB: ENGAGING YOUNG CHILDREN WITH EARTH SCIENCE IN KENYA. WHAT WE HAVE ACCOMPLISHED SO FAR

    Although most of East Africa’s volcanoes are currently dormant they could erupt in the future, while 25% of Africa’s volcanoes had eruptions in the last 100 years. How to be prepared and respond to natural hazards such as volcanoes, need to be communicated to young children, learning settings and communities. The project presented here has been funded by IUGG and supported by IAVCEI within the priority area Geoscience Education and Outreach in Developing Countries. It aims to present the Paper Volcanoes toolkit and create a dialogue between science and the indigenous knowledge to communicate natural hazards to children considering their identity and context. The Paper Volcanoes Laboratory toolkit is an experience based activity enriched with pedagogical elements, created within the INGV Educational Group, to help early childhood children to familiarize themselves with natural hazards including volcanoes. The project focuses on the Turkana rural setting in Kenya where the regional volcanism is known by geologists or indigenous people through their traditional stories. Here we present the methodology used, the preparatory pilot involving four universities students and Turkana early childhood teachers to experience the Paper volcano toolkit and the extended pilot. The pilot was run in September 2022 in Lodwar and consisted of four themed workshops involving stakeholders, teachers (40) and elders. The pilot enabled teachers to hear the stories about the Turkana mountains, experience the paper toolkit, to share ideas, to connect with geoscience specialists and sociologists.
      92  92
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Breaking Adria and Southern Italy: adjoint tomography of an intricate lithosphere

    High-resolution adjoint tomography has emerged as a powerful tool for unraveling the complexities of the Earth's lithosphere. We present an overview of the analysis conducted on the seismic images generated by the application of high-resolution adjoint tomography for the lithosphere beneath Southern Italy and the Adriatic region. Recently, we have proposed IMAGINE_IT, a reference 3D high-resolution seismic tomography model for tectonic and geological structures of the Italian lithosphere. Enhanced accuracy is enabled by state-of-the-art methods, including three-dimensional wavefield simulations based on SPECFEM3D in combination with an adjoint-state method. Adria plate plays a peculiar role in the geodynamics of the Central Mediterranean. It is the foreland of non-coeval mountain ranges and its margins are consumed in the process by subduction systems under the Alps to the north, the Apennines to the west and the Dinarides to the east. The complex behavior of this system and the large geographical heterogeneity in data availability lead to a fragmented understanding of the Adria plate. In particular, its lithospheric structure, in terms of Vp and Vs profiles, is poorly known due to a lack of seismic stations, poor earthquake location quality (large observational gaps), and the consequent lack of coverage by classical seismic tomography methods. The uncertainties increase the difficulty of correctly assessing the seismic hazard along the Adriatic coasts (including tsunami hazard evaluation). Here, we present additional details of this region, such as the mid-Adriatic ridge, and a preliminary set of iterations that exploit 7 years of additional data (IMAGINE_IT was limited to data until 2015) and the recent deployment of very dense regional arrays of broadband seismic stations– the 2016-2019 AlpArray and the AdriaArray Seismic Network currently under installation – which provide a new opportunity to improve our comprehension of the area. Furthermore, we focus on southern Italy, starting from L’Aquila region up to Calabrian Arc. The analysis of the images produced by high-resolution adjoint tomography IMAGINE_IT reveals intricate details of the lithospheric architecture, including crustal thickness variations, seismic velocity anomalies, and (lack of) subduction-related features.
      36  98
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Adjoint tomography of the Italian lithosphere

    The evolution and state of geological structure at Earth’s surface is best understood with an accurate characterization of the subsurface, where fluid distribution plays a key role. We present high-resolution seismic tomographic images of tectonic and geological features of the Italian lithosphere based on ground motion recordings and obtained through an iterative procedure. Enhanced accuracy is enabled by state-of-the-art three-dimensional wavefield simulations in combination with an adjoint-state method. The resulting tomographic model characterizes the subsurface structure in terms of compressional and shear wavespeed values at remarkable resolution, corresponding to a minimum period of ~10 s. As primary findings of our work, images of the lithospheric structure in Central Italy are consistent with recent studies on the distribution of fluids and gas (CO2) within the Italian subsurface, allowing us to infer the presence of deep melted material that induces shallow gas fluxes, or traps and deep storage of gas that can be correlated with seismicity. We illuminate Mt. Etna volcano and support the hypothesis of a deep reservoir (~30 km) feeding an intermediate-depth magma-filled intrusive body, which in turn is connected to a shallow chamber. We also investigate the intriguing features of the Adriatic plate offshore of the eastern Italian coast. Tomographic evidence reveals a structure of the plate made of two distinct microplates with different fabric and behavior, and separated by the Gargano deformation zone, indicating a complex lithosphere and tectonic evolution.
      31  71
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    What we can say (or not) about the seismic sequence of the November 9th 2022, Mw 5.5, earthquake in the Marche offshore: an analysis of the Italian Seismic Bulletin on phase interpretation, velocity models and uncertainties of earthquake locations

    Introduction In November 2022 a seismic sequence occurred in the Marche offshore, about 29 km from the coast and the city of Fano. The sequence started on November 9 (06:07:25 UTC) with a ML=5.7 earthquake (Mw=5.5 from TDMD computation, Scognamiglio et al., 2006), immediately followed by a ML=5.2 earthquake (06:08:29 UTC) located about 8 km to the south. The two mainshocks activated a seismic sequence with about 400 aftershocks lasting the first week, 13 of them with ML>= 3.5 (Fig. 1). Few hours after the occurrence of the mainshock, the BSI (“Bollettino Sismico Italiano”) working group started to manually analyze P and S phase arrival times and seismogram amplitudes of earthquakes with magnitude ML>= 3.5 recorded by the the Italian National Seismic Network (Rete Sismica Nazionale, hereafter RSN) in order to better constrain hypocenter locations previously provided by the seismic surveillance room of the INGV in Rome for rapid communication to the Italian Civil Protection (Dipartimento Protezione Civile, DPC). Later, the BSI working group analyzed the seismicity of the sequence of the first weeks of seismic activity by revising hypocentral parameters of more than 500 events. The 2022 Marche offshore sequence took place along the Adriatic outer front of the northern Apennines in central Italy. Offshore seismic reflection profiles image a shallow thrust-and-fold system striking WNW–ESE to NNW–SSE. Along the coastal Adriatic area, active blind thrusts deform Plio-Quaternary siliciclastic turbidites that are few hundreds of meters to more than 2 km thick in correspondence of ramp anticlines and synclines, respectively. In a recent work, through the analysis of high-quality background seismicity data, De Nardis et al. (2022) identified two lithospheric-scale active thrusts deepening westward under the Adriatic outer front from upper- to lower-crustal depths. These new data support previous thick-skinned interpretations of seismic commercial profiles and CROP03 deep reflection data (Lavecchia et al., 2003). Focal mechanisms of weak to moderate (ML < 4.8) local earthquakes occurred between 2009-2017 at upper- to deep-crustal depths show prevailing reverse and reverse/oblique solutions (De Nardis et al., 2022) and subordinate strike-slip faulting (Mazzoli et al., 2014). The analysis of the 2022 Marche offshore sequence opens again the discussion on the uncertainties related to the hypocenter locations of earthquakes that occur in the Adriatic offshore domain (e.g., Di Stefano et al., 2022) and the limits of our present capability to provide an accurate seismotectonic interpretation of the instrumental seismicity in this region. Actually, the 2022 sequence area is only covered on land by RSN, with the closest seismic station located at about 28 km from the epicentral location of the mainshock. The particular geometry of the network along the Italian coast makes it difficult to correctly constrain hypocenter locations compared with other regions of Italy. Taking into account this configuration, although the INGV is able to obtain coherent earthquake information for Civil Protection purposes into the limits of the communication threshold, we note that data provided by the seismic surveillance room in terms of both seismic phase readings of arrival times for hypocenter location and waveform amplitudes for magnitude computation need to a more accurate analysis if the main goal is the correct reconstruction of the active structures involved in the sequence. This analysis should include a) a careful revision of the arrival time pickings to reduce the errors due to seismic phase misinterpretations, b) an accurate study to constrain earthquake locations with appropriate velocity models, and c) the hypocenter solution assessment through adequate tests that define which information can be inferred from earthquake location results. Data analysis and phases interpretation Through the interpretation of the seismic records, the BSI analysts have identified refracted first arrivals of P and S phases at epicentral distances of about 60 km, smaller than those expected for Pn/Sn refracted phases at the Moho discontinuity (e.g., Di Stefano and Ciaccio, 2014) whose arrivals should be observed at distances of about 90-100 km in this area. Since possible systematic misinterpretation of P and S arrivals can strongly affect the correct hypocenter locations, we have carefully revised the phase pickings provided by the INGV surveillance room by discriminating direct from refracted phases at stations located at distances greater than 60 km. This is mainly important for interpretation of weak S refracted phases that are often hidden into the arrivals after the P phase. We have taken into account these characteristics in the earthquake location process by only using clear direct/refracted S phases in our inversion procedure. The comparison of the ML>= 3.5 hypocenter locations performed by the BSI and the INGV surveillance room (Figs. 1 and 2) shows how an accurate analysis of the pickings is necessary to obtain robust earthquake locations for seismotectonic interpretation: even using the same hypocenter location code and velocity model, we observe that the mislocation of the hypocenters in this area can range from few to about 10 kilometers (Fig. 1) while the formal errors are strongly reduced after the BSI picking revision (Fig. 2) The velocity model issue Events location in the Adriatic Sea suffers from the lack of a specific velocity model for the seismic sequence area. The use of inadequate velocity parameters during the location process can introduce systematic errors, which may result in incorrect seismotectonic interpretations. We therefore built and tested different velocity models from both available geophysical data and our inversion of the velocity structure using the arrival time readings revised by the BSI working group. In order to define deterministic 1D models suitable for earthquake location (Vp and Vp/Vs), we integrated sonic logs from local deep wells (ViDEPI Project, 2005) with literature data that include: seismic commercial profiles, deep seismic refraction surveys, the CROP03 crustal profile, Receiver Function and regional seismic tomography models, Vp/Vs reference values for mid- and lower-crustal crystalline rocks (Coward et al., 1999; Ponziani et al., 1995; Lavecchia et al., 2003; Spada et al., 2013; Di Stefano et al., 2009, Christiansen and Mooney, 1993). In order to obtain the velocity structure from our revised dataset, we first determined the Vp/Vs ratio by using the arrival time pickings of selected P and S phases. The mean velocity ratio Vp/Vs was computed through the cumulative Wadati diagram. Then, by collecting all the a priori available information regarding the structure of Adriatic Sea (velocities, layer thicknesses and Moho depth), we applied the VELEST software (Kissling, 1995) to compute a new 1D velocity model for earthquake location. Conclusions In this work we present our first analyses of the sequence and the accurate study of the velocity models that we obtained from both a revision of available data and the inversion of arrival time pickings analyzed by the BSI analists. Moreover, we will discuss our preliminary earthquake locations with a particular attention to resolution analysis and hypocenter location assessment.
      187  194
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Absolute gravity and deformation measurements for a multi-disciplinary study in Central Italy

    Since 2018, INGV funded 3 projects aimed to detect ground deformations and gravity variations over different timescale in the area where the recent seismic events of L’Aquila (2009, Mw 6.3) and Amatrice-Norcia (2016, Mw 6.1 and 6.5) took place. The consequent static deformation field reached several centimetres and the modelled impact of such events could have modified the gravity field up to 170 μGal. Furthermore, the medium-long-term gravity and ground deformation variations related to post-seismic relaxation are expected as consequence of vertical deformation of the Earth surface and/or of the internal boundaries separating layers at depth with different densities. In addition, the L’Aquila area is affected by deformations induced by ground water level changes in the aquifers. Therefore, a multidisciplinary approach carrying out joint measurements of deformation and gravity is fundamental to understand the role of each geophysical process. To this aim, a network of 3 (Terni, Popoli, Sant’Angelo Romano) new non-permanent GNSS stations was realized outside the buildings hosting the absolute gravity stations. At L’Aquila, a permanent GNSS station managed by the Italian Space Agency (AQUI) is continuously working on the rooftop terrace of the Science Faculty, and positioned vertically with respect to the gravimetric station (AQUIg), which is located 4 floors below. Since 4 absolute gravimetric sites are located indoor, the precise coordinates of the gravity benchmark have been obtained by classical topographic surveys, connecting the indoor site to the outdoor GNSS reference point. Here we present the gravity and ground deformation variations observed in the period 2018-2022 after five measurement campaigns.
      67  120
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Earthquakes and story maps

    Since 2013, the Earthquake Department of INGV has used story maps as a new communication and information channel on seismicity and seismic risk of the national territory. Numerous story maps have been developed to tell the various aspects of the earthquakes that have struck in the past, and in recent years, our country by integrating descriptive, photographic and multimedia information with georeferenced data from the INGV seismological and seismotectonic databases [Pignone , 2015]. A story maps is an integrated set of digital maps, related content (legend, text, photos, videos, etc.) and interaction features (pan / zoom, pop-up, query, select, etc.) that make it an easily understandable and an immediate information and communication product. For this reason, they have also become a very valid tool in the dissemination events that INGV promotes using touch screens that allow you to create real exhibits with which to interact with the public, demonstrating the potential of geographic information in risk communication. After the creation of the story maps, it was decided to also use the web applications of the dashboards type that allow you to make various tools for viewing the datasets and related attributes available, in order to create simple infographics, very effective for communication and information for inexperienced users. ESRI ArcGIS online technology (https://www.arcgis.com/) was used to create story maps and dashboard, a cloud-based sharing platform that allows you to build web maps by integrating your datasets with a rich collection of basic geographic data with worldwide coverage. With these web maps it is possible to create, using appropriate templates available, different types of web applications, publish them and share them on the web. From 2013 to today, over 25 story maps and dashboards have been published to tell about some of the most important earthquakes and tsunamis of the past in Italy and the Mediterranean but also to analyze some of the recent seismic sequences that have affected the Italian territory. There were about 110 thousand views of the story maps and dashboards published (Fig. 1).
      44  63
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Breaking Adria: adjoint tomography of a disappearing continental microplate

    The Adria plate plays a peculiar role in the geodynamics of the Central Mediterranean. It is the foreland of non-coeval mountain ranges and its margins are consumed in the process by subduction systems under the Alps to the north, the Apennines to the west and the Dinarides to the east. The complex behavior of this system and the large heterogeneity in data availability lead to a fragmented understanding of the Adria plate. In particular, its lithospheric structure, in terms of Vp and Vs profiles, is poorly known due to a lack of seismic stations, poor earthquake location quality (large observational gaps) and the consequent lack of coverage by classical seismic tomography methods. The uncertainties increase the difficulty of correctly assessing the seismic hazard along the Adriatic coasts (including tsunami hazard). Recently, we have proposed IMAGINE_IT, a reference 3D high-reso- lution seismic tomography of the Italian lithosphere. Enhanced accuracy is enabled by three-dimensional wavefield simulations based on SPECFEM3D in combination with an adjoint-state method. The Adria plate is located at the eastern border of the volume considered in the simulations, nevertheless, our tomography is able to image this plate with an unprecedented resolution and supports the idea that it is made of two distinct microplates having dif- ferent fabric and behavior and separated by the Gargano deformation zone. We have highlighted a northern portion with more complex wavespeed anomalies and a thinner crust, and a southern part with a more regularly layered wavespeed structure and a thicker crust. Here, we focus on additional details of those images, such as the mid-Adriatic ridge and a new set of iterations that exploit 7 years of additional data (IMAGINE_IT was limited to data until 2015) and the 2016-2019 AlpArray very dense regional arrays of broadband seismic stations which provide a new opportunity to improve our comprehension of the area.
      56  110
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Central Italy high-resolution model for accurate ground motion simulation

    A challenge in earthquake seismology is the provision of realistic and accurate ground-shaking scenarios for seismic hazard and risk assessment. Owing to the exponential growth of HPC resources, the application of physics-based methods to ground motion characterization has become increasingly popular. However, physics-based techniques could break down in the simulation of high-frequency ground motion, particularly at frequencies higher than 1 Hz, which are the most relevant for earthquake engineers. A main issue is represented by the limited resolution of seismic wave speed models. Currently, one of the best approaches to retrieve high-resolution wave speed models relies on the combination of the Spectral Element Method (SEM) with adjoint-state methods within the framework of (3D) Full Waveform Inversion (FWI). Here we use the Salvus software to resolve the velocity structure of central Italy, which is exposed to high seismic hazard. We invert a dataset including 248 events (occurred between 2005 and 2019, with a magnitude ranging between 2.8 and 5.5) recorded by the Italian seismic network and provided by INGV. We implement a multi-scale approach to 3D-FWI by progressively incorporating the high-frequency content of waveform recording. In the first cycle of iterations, we retrieve the long-wavelength structure of the model. At this stage, we also perform several tests, e.g. different source/receiver cutouts, to properly tune the FWI configuration parameters to our problem. Then we use the best fitting model as the initial model of a second cycle of iterations, combining it with Vs30 and topographic data. By accounting for site effects, we maximize the level of detail in the starting model, thus preventing the FWI algorithm from being trapped in local minima. The retrieved high-resolution wave speed model will shed light on the velocity structure of central Italy, thus improving the seismic hazard assessment of this region.
      52  86
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Seismic behaviour and 3D reconstruction of Cultural Heritage: the Column of the Hera Lacinia Temple in Capo Colonna (Calabria, Southern Italy)

    The study aims to characterize the seismic behaviour of the Doric Column, last remaining of the Hera Lacinia Temple, located on the promontory of Capo Colonna near Crotone (Calabria, Southern Italy). Recordings of ambient vibration has been acquired both at the base and on the top of the column, simultaneously, in order to detect the predominant frequencies of the element. In addition, a high-resolution 3D model of the column has been reconstructed through laser scanning to support the analysis of the current state of the heritage element. The fundamental frequencies of the column and those associated to the site have been compared to verify potential resonance phenomena at the occurrence of an earthquake. In addition, a significant inclination of the column was detected by analysing the 3D model.
      20  109