D'Anna, Roberto
Preferred name
D'Anna, Roberto
Email
roberto.danna@ingv.it
Staff
staff
ORCID
13 results
Filters
Settings
The search returned 13 results
Now showing 1 - 10 of 13
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Real-time urban seismic network and structural monitoring by means of accelerometric sensors: Application to the historic buildings of Catania (Italy)
A real-time urban seismic network for seismic and structural health monitoring is being installed in the city of Catania (Sicily, Italy). The 27 monitoring stations, specifically designed and assembled, equipped with a low-noise 3-axial MEMS accelerometer, are located in 23 high exposure and vulnerability buildings. In this paper we present the characteristics of the monitoring station and of the network. In case of strong seismic events, the system will provide shake maps to the emergency management centre, and will allow to assess the health conditions of the monitored buildings. The network is conceived to be further expandable over the whole historical city centre of the city of Catania.115 3 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , The marine activities performed within the TOMO-ETNA experiment
The TOMO-ETNA experiment was planned in order to obtain a detailed geological and structural model of the continental and oceanic crust beneath Mt. Etna volcano and northeastern Sicily up to the Aeolian Islands (southern Italy), by integrating data from active and passive refraction and reflection seismic methodologies, magnetic and gravity surveys. This paper focuses on the marine activities performed within the experiment, which have been carried out in the Ionian and Tyrrhenian Seas, during three multidisciplinary oceanographic cruises, involving three research vessels (“Sarmiento de Gamboa”, “Galatea” and “Aegaeo”) belonging to different countries and institutions. During the offshore surveys about 9700 air-gun shots were produced to achieve a high-resolution seismic tomography through the wide-angle seismic refraction method, covering a total of nearly 2650 km of shooting tracks. To register ground motion, 27 ocean bottom seismometers were deployed, extending the inland seismic permanent network of the Istituto Nazionale di Geofisica e Vulcanologia (INGV) and a temporary network installed for the experiment. A total of 1410 km of multi-channel seismic reflection profiles were acquired to image the subsurface of the area and to achieve a 2D velocity model for each profile. Multibeam sonar and sub bottom profiler data were also collected. Moreover, a total of 2020 km of magnetic and 680 km of gravity track lines were acquired to compile magnetic and gravity anomaly maps offshore Mt. Etna volcano. Here, high-resolution images of the seafloor, as well as sediment and rock samples, were also collected using a remotely operated vehicle.1041 361 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Il nuovo OBS/H dell’INGV
(2009-02-09); ; ; ; In 2005, thanks to the 3-year agreement between Dipartimento Nazionale della Protezione Civile (DPC) and Istituto Nazionale di Geofisica e Vulcanologia (INGV) - Centro Nazionale Terremoti (CNT), the project of the first Italian “Ocean Bottom Seismometer with Hydrophone” (OBS/H) for long-term deployment was developed at the OBS Lab of the Gibilmanna Observatory (Sicily). The drawing of the instrument started in January 2005 and, after 18 months, the prototype was ready for test in laboratory, in shallow and deep water. Afterwards, the first OBS/H was tested during an oceanographic campaign on the Marsili submarine volcano, from the 10th to the 21st of July 2006.More than 1000 events of several kinds were recorded: 817 VTB (Volcano Tectonic events, B-type), 159 HF (High Frequency events), 53 SDE (Short Duration Event), 8 regional events localized by INGV land network, 10 not localized events, 1 teleseismic event an 2 rockfall events. The INGV OBS/H are equipped with: - Nanometrics Trillium 120p seismometers (theoretical flat response between 120s and 175 Hz) installed in a 17 inches glass sphere on a Nautilus gimbal for the leveling or Guralp CMG40T-OBS (flat response between 60s and 100 Hz); - Cox-Webb Differential Pressure Gauge (bandwidth 500s-2Hz) or OAS E-2PD hydrophone (0-5kHz); - 21 bits, 4 channels SEND Geolon-MLS digitizer with sampling frequency up to 200 Hz.262 442 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , MICROTREMOR MEASUREMENTS IN PALERMO, ITALY: A COMPARISON WITH MACROSEISMIC INTENSITY AND EARTHQUAKE GROUND MOTION
The city of Palermo is an appropriate test site where the efficiency of microtremors in predicting ground motion properties during earthquakes can be checked. Palermo is a densely populated city with important historical heritage and was object of previous studies. Areas of local amplification of damage were identified in downtown Palermo using historical macroseismic data. Moreover, aftershocks of the September 6, 2002, earthquake (Mw 5.9, 40 km offshore) provided a dataset of seismograms that quantify spatial variations of ground motion. The availability of more than 2000 boreholes in the city allowed a reconstruction of the 3D structure of surface geology, indicating that all the higher damage zones correspond to sediment-filled valleys. The high variability of the surface geology is mostly due to the presence of two filled river-beds of about 150 m width. In the framework of the SESAME project (Seismic EffectS assessment using Ambient Exctations, funded by the European Union), 90 microtremor measurements were performed across several profiles crossing the soft sediment bodies. The measurement points were intensified close to the valley edges (every 20 m), according to our geological reconstruction. H/V spectral ratio on ambient noise (HVSR) show significant variations along each profile: as soon as the transition stiff to soft is crossed, a typical spectral peak exceeding a factor of 3 in amplitude appears in the HVSR. The peak falls between 1 and 2 Hz and, along each profile, the peak disappears as soon as the other edge of the valley is crossed. These results indicate that microtremors are sensitive to the presence of large impedance contrasts of deep soft soil, at least in the Palermo area, with an important implication: the HVSR method seems to be able to recognize conditions potentially favourable to the occurrence of higher damage even when local geological characters are masked by the urban growth. However, we were not able to establish a quantitative correlation between microtremor properties and ground motion (or damage) amplification.296 354 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Monitoring Earthquake through MEMS Sensors (MEMS project) in the town of Acireale (Italy)
We introduce the realization of the first European real-time urban seismic network based on Micro ElectroMechanical Systems (MEMS) technology. The project is called Monitoring Earthquake through MEMS Sensors (MEMS) and encompass the installation of about 100 seismic station in the municipality of Acireale (Sicily, Italy). The stations, specifically designed and assembled, are equipped with a triaxial MEMS accelerometer, and gyroscope and GPS. In this paper we present the characteristics of the station and of the network. The main objective of the network is a rapid, post-earthquake disaster assessment through the automatic production of shake maps. The network also allow the implementation of an automatic recognition system for damage assessment from remotely piloted aircraft, and of a site-specific Earthquake Early Warning system.77 9 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , First long time OBS campaign in the Ionian Sea
(2008-07-11); ; ; ; The INGV started its interest to extend the seismic monitoring network to the sea in 1995 with GEOSTAR (Geophysical and Oceanographic Station for Abyssal Research) project, coming out with the realization of the first multidisclipinary observatory for deep-sea monitoring [Favali et al. 2002]. At the end of 2004, the National Earthquake Center (CNT) of INGV decided to provide a pool of Ocean Bottom Seismometers to be employed as a submarine mobile network and to study submarine faults and volcanoes. This was possible thanks to an agreement between the INGV and the Italian National Civil Protection Department (DPC). On July 2006, the Gibilmanna OBS Lab, tested the first OBS prototype for nine days on the flat top of the Marsili submarine volcano [D’Anna et al. 2007] and in early 2007 other seven OBS’s were ready to be deployed on the seafloor. In May 2007, within the European project NERIES (activity NA6), the Gibilmanna OBS Lab of the INGV has deployed three Broad Band Ocean Bottom Seismometers (BBOBS) in the southern Ionian Sea at 3500-4000 meters of depth. This area has been chosen during the NERIES – “NA6-BBOBS net” meeting in Rome, on the 11th of September 2006 because at first, there are at the moment few seismological data [Scrocca et al., 2003] to construct a reliable model for the Ionian lithosphere and also the rate and features of the seismicity in the area between the Hyblean-Malta fault system and the accretionary prism of the Calabrian Arc are largely unknown [Catalano et al. 2002]. The Ionian Sea is indeed one of the most seismically active area in the Mediterranean region with several destructive earthquakes sometimes followed by tsunamis [Tinti et al. 2004]. The seismicity occurring in the Ionian basin is characterized by large location uncertainties due to the lack of seafloor seismic stations. In 2002, the quality of the seismic sensing and the location of earthquakes have been improved by the deployment of the real-time submarine observatory SN-1, about 25 km offshore Eastern Sicily [Sgroi et al, 2007]. However, the SN-1 location only allows to characterize the seismicity in the area offshore the eastern Sicily. Two of the three OBS’s were successfully recovered on the 2nd of February 2008; the last one was recovered on the 15th of March 2008 and another OBS was deployed on the same location to accomplish the continuous long-term seismic monitoring task (until May 2010) as planned in NERIES project.273 471 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Il primo OBS/H italiano per il monitoraggio e lo studio di faglie e vulcani sottomarini
(2006-11-28); ; ; ; L’Istituto Nazionale di Geofisica e Vulcanologia (INGV) ha testato con successo, nel luglio 2006, il primo Ocean Bottom Seismometer with Hydrophone (OBS/H) italiano (Fig. 1). Lo strumento, interamente progettato e realizzato all’Osservatorio di Gibilmanna del Centro Nazionale Terremoti, dopo aver superato i test in laboratorio, in camera iperbarica a 600 bar ed in mare a 3412 m di profondità, è stato deposto per 9 giorni (12-21/07/’06) sulla spianata sommitale del vulcano sottomarino Marsili a 790 m di profondità (Fig. 2) ed ha registrato 835 eventi tra cui un telesisma, 8 eventi regionali e circa 800 eventi vulcanici.La realizzazione dell’OBS/H si colloca nell’ambito dei progetti finanziati dalla convenzione tra l’INGV e il Dipartimento Nazionale della Protezione Civile (DPC), che ha avuto come obiettivo la costituzione di un primo pool strumentale, costituito da 7 OBS/H, da impiegare come rete mobile sottomarina in occasione di forti eventi sismici che dovessero interessare le coste e i mari italiani. Tale progetto si inquadra in uno scenario di ben più ampio respiro che vedrà nei prossimi anni l’estensione a mare della rete sismica nazionale, obiettivo strategico inserito nel piano triennale dell’INGV che porterà entro il 2008 alla realizzazione della prima stazione italiana real-time collegata a terra via radio, che verrà posizionata a circa 30 miglia a sud-est di Ustica, luogo in cui è stato localizzato il terremoto di Palermo del 6 settembre 2002. Il prototipo di OBS/H utilizzato nel test sul Marsili è stato equipaggiato con un sensore sismico Trillium 40s della Nanometrics ed un idrofono OAS E-2PD con banda di risposta piatta tra 0 e 5 kHz. I segnali emessi da questi strumenti sono stati registrati da un digitalizzatore a 21 bit a basso consumo (Geolon MLS della SEND) che ha acquisito i dati ad una frequenza di campionamento di 200 campioni al secondo, per sfruttare il più possibile l’ampia banda di risposta dell’idrofono, al fine di mettere in evidenza l’attività idrotermale del vulcano. Il sensore sismico è posto all’interno di una bentosfera di 17 pollici (sfera di vetro certificata per operazioni sino a 6000 m di profondità), installato su una base autolivellante controllata elettronicamente. Il digitalizzatore e le batterie sono poste all’interno di un contenitore in ERGAL 7075. Per il recupero dello strumento a fine esperimento, è stato utilizzato uno sganciatore acustico IXSEA AR816S-MR opportunamente modificato dal personale dell’osservatorio di Gibilmanna per attivare, una volta ricevuto il segnale di “release”, un sistema di sgancio elettrolitico (burn-wire). Per deposizioni di lungo periodo, sino ad uno o due anni in relazione al tipo di sismometro a bordo, l’OBS/H sarà dotato della strumentazione indicata nella Tab. 1 Attualmente è in fase di progettazione un’evoluzione dello strumento che mira a dotarlo di un digitalizzatore a 24 bit, di un sistema di comunicazione basato su modem acustico e di un PC industriale con processore ARM grazie al quale, nell’eventualità di interventi della rete mobile sottomarina, sarà possibile estrarre tracce degli eventi verificatisi per una più accurata localizzazione dell’epicentro senza che si renda necessario il recupero dello strumento. Inoltre, mediante l’implementazione di algoritmi di trigger, sarà possibile l’utilizzo dell’OBS/H all’interno di un sistema di allerta tsunami in comunicazione con una boa di superficie collegata al centro di controllo via satellite.184 702 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , PROGETTO “MESSINA 1908 – 2008”. RAPPORTO DELLA CAMPAGNA OBS NELL’AREA EOLIANA E DELLO STRETTO DI MESSINA
Il Centro Nazionale Terremoti (CNT), in collaborazione con la sezione di Catania, ha progettato e realizzato un esperimento di sismica passiva nell’area Calabro–Peloritana il cui scopo è fornire nuovi dati sismici volti a comprendere come le dinamiche superficiali ed il processo di subduzione interagiscano tra loro, migliorando così la comprensione dei processi sismogenetici nella zona colpita dal terremoto del 1908 [Margheriti et al., 2008; http://dpc-s5.rm.ingv.it]. Con l’obiettivo di ridurre l’errore di localizzazione degli ipocentri degli eventi verificatisi nell’area interessata dal progetto, ad integrazione delle 30 stazioni della rete sismica nazionale già presenti nell’area in esame, l’esperimento ha previsto l’installazione di 15 stazioni della rete mobile e la deposizione di 5 OBS/H (Ocean Bottom Seismometer with Hydrophone), per un numero complessivo di 50 stazioni sismiche larga banda 3C coinvolte nel progetto. La campagna sismica a terra ha avuto inizio nell’ottobre 2007 e ad oggi (gennaio 2009), le stazioni sono ancora in funzione, mentre la deposizione dei cinque OBS/H è avvenuta tra il 15 e il 18 luglio 2008 ed il loro recupero è stato effettuato tra il 6 e il 7 novembre 2008. Gli OBS/H, progettati e realizzati presso l’OBS Lab di Gibilmanna, sono stati equipaggiati con sismometri Nanometrics Trillium 120p (120s - 175 Hz) e con sensori differenziali di pressione (Differential Pressure Gauge) Cox-Webb, con banda passante tra i 200s e i 2Hz. La base autolivellante sulla quale è installato il sensore sismico è stata realizzata anch’essa presso l’OBS Lab di Gibilmanna nei mesi intercorsi tra il recupero degli OBS impiegati nella prima campagna NERIES, avvenuto nel marzo 2008, e il luglio 2008, data della deposizione degli OBS del progetto “Messina 1908 – 2008”. La necessità di realizzare una nuova base autolivellante in tempi così brevi, è stata una diretta conseguenza dei risultati negativi ottenuti dalla base Nautilus in occasione della già citata campagna NERIES [D’Anna et al., 2008]: due sismometri su tre non si erano livellati nel range di ±0.2°, massimo tilt dinamico previsto per i Trillium 120p, provocando il non funzionamento degli stessi. Come meglio verrà analizzato nei paragrafi successivi, le problematiche affrontate nella realizzazione di questi dispositivi di livellamento sono state molteplici e di difficile soluzione. L’analisi preliminare dei dati ha evidenziato che soltanto uno dei cinque sensori sismici ha funzionato correttamente per l’intero periodo, mentre gli altri quattro hanno funzionato in media per circa 20 giorni. Causa di ciò, un rapido consumo delle batterie dovuto ad un livellamento sì compreso nel range di ±0.2° dall’orizzontale, condizione necessaria perché il sismometro sia in grado di rilevare eventi sismici, ma oltre il range di ±0.1°, condizione necessaria perché i consumi del Trillium120p si riducano da circa 2.5W ai 600mW nominali. I risultati ottenuti da questo esperimento, sono comunque da inquadrare in una successione degli eventi che ha fatto sì che lo sviluppo di questa nuova base autolivellante fosse condizionato da una certa urgenza: al CNT premeva presentare i dati raccolti dagli OBS al convegno “Scienza e società a 100 anni dal grande Terremoto”, che si sarebbe tenuto a Reggio Calabria dal 10 al 12 dicembre 2008 e visti gli insuccessi della base Nautilus nel precedente esperimento, ci si è trovati di fronte alla necessità di progettare e sviluppare un nuovo sistema di livellamento per i Trillium 120p nell’arco di tre mesi e mezzo. Queste, oltre a quelle di natura economica, le ragioni per cui non è stato possibile procedere secondo un iter che per noi, come per le aziende che operano nel settore marino, è uno standard: - Progettazione; - Realizzazione del prototipo; - Test in laboratorio (e. g. tavola vibrante) - Test in camera iperbarica; - Test in mare; - Produzione in serie; E’ nostra intenzione, in un prossimo futuro, portare avanti lo sviluppo di questa base autolivellante, con tempi e risorse finanziare ed umane più appropriate. Ciò che riportiamo in questo Rapporto Tecnico vuole essere una descrizione del lavoro sin qui svolto, anche se non conclusivo e risolutivo, ma che ci ha già permesso di individuare delle problematiche fondamentali la cui soluzione sarà oggetto di studi più approfonditi. Rimane positivo il fatto che le basi già realizzate riescono già da adesso a livellare automaticamente un sensore entro un range di ±0.2°. Gli OBS/H dell’INGV verranno nuovamente deposti con la stessa disposizione del progetto “Messina 1908 – 2008” nell’estate 2009, nell’ambito del progetto S5 finanziato dal Dipartimento della Protezione Civile. Per sopperire alle problematiche riscontrate nella marinizzazione del Trillium 120p, si è scelto di installare a bordo degli OBS dei sensori Guralp CMG40T-OBS (60s – 100 Hz), progettati per installazioni in mare sino a profondità di 6000 m è già dotati di una propria base autolivellante. Il motivo per il quale non si è utilizzato nelle passate campagne questo tipo di sensore è da addebitare unicamente al fatto che sui fondi DPC della convenzione 2005-2007 non è stato possibile inserire l’acquisto di questi specifici sensori, mentre erano disponibili i Trillium 120p.213 537 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Sviluppo di una stazione sismica low-cost basata su tecnologia MEMS
The impact of a strong earthqauke onto an urban community can be reduced taking timely actions managed by the authority in charge for the civil protection. In this view, it is of fundamental importance that the authority in charge for the seismic surveillance is provided with the appropriate monitoring tools able to give the most useful information for the best emergency management in the immediate postevent. Today this goal can be reached realizing urbanscale, realtime seismic monitoring networks (Osservatori Sismici Urbani, OSU, in Italian). The realtime OSU networks are able to promptly provide information to the emergency authority about the ground shaking at each node after an earthquake. Maps showing the spatial distribution of the ground shaking could help in the optimization of the priorities and a good management of the rescue resources in order to reduce the number of victims. Also the assessment of the damage of the buildings could be carried out according to the logic of priority given by the shakings measured by the OSU. The realisation of OSUs is the main objective of the MEMS project. This project is funded by the MIUR under the SIR program (Scientific Independence of young Researchers). The first challenge of the MEMS project was the design and the development of a devoted accelerometric stations. This work illustrates in detail the accelerometric station based on MEMS technology (Micro ElectroMechanical Systems). The final product is a lowcost accelerometric station with high performance and great versatility.931 43 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Il primo OBS/H italiano per il monitoraggio e lo studio di faglie e vulcani sottomarini
(2006); ; ; ; L’Istituto Nazionale di Geofisica e Vulcanologia (INGV) ha testato con successo, nel luglio 2006, il primo Ocean Bottom Seismometer with Hydrophone (OBS/H) italiano (Fig. 1). Lo strumento, interamente progettato e realizzato all’Osservatorio di Gibilmanna del Centro Nazionale Terremoti, dopo aver superato i test in laboratorio, in camera iperbarica a 600 bar ed in mare a 3412 m di profondità, è stato deposto per 9 giorni (12-21/07/’06) sulla spianata sommitale del vulcano sottomarino Marsili a 790 m di profondità (Fig. 2) ed ha registrato 835 eventi tra cui un telesisma, 8 eventi regionali e circa 800 eventi vulcanici.222 174
