GFZ-Potsdam
9 results
Filters
Settings
The search returned 9 results
Now showing 1 - 9 of 9
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Microseismicity recorded in the geothermal areas of Mt. Amiata (Italy)
(2019-04); ; ; ; Mt. Amiata (Tuscany, Italy) is an extinct volcano whose last eruptive activity was dated about 200 ky ago. Today, its underlying crustal volume is still characterized by a high geothermal gradient, which makes the area particularly suitable for geothermal exploitation. Seismicity in the Tuscan Geothermal Areas is generally observed within the upper crust and is confined in depth by the so called K-horizon, a strong seismic reflector located in between 4-8 km b.s.l., often interpreted as the 400°C isotherme. The overlaying structure presents permeable layers of highly fractured volcanic rocks, saturated with hot water and steam. Geothermal exploitation from these layers started in the 1960's. Since then, shallow earthquakes have been occasionally observed close to the geothermal wells, and the question is whether these event are of natural origin or related to the exploitation of heat. To monitor the seismic activity inside the geothermal field of Mt. Amiata, we installed in 2015 a dedicated 8-station seismic network in the vicinity of the productive geothermal power plants for a 3-years recording period. The main challenges of our experiment are to automatically detect and locate the local microseismicity, trying to discriminate from natural seismicity those events caused by human operations. Due to the strong regional seismic activity of the 2016 Central Italy sequence, the automatic detection of local seismic events resulted challenging. We therefore use a waveform based detector (Lassie, developed at GFZ) to quickly scan the large dataset and automatically detect weak events in the target volume. Lassie provides preliminary event locations, which are then refined in a second step, using standard and waveform based techniques. For those hypocenters that are located close to the geothermal power plants, at a similar depth as the production level (3500 m b.s.l.), it remains very challenging to discriminate between natural and anthropogenic events.88 119 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Discrimination between induced, triggered and natural earthquakes close to hydrocarbon reservoirs: A probabilistic approach based on the modeling of depletion-induced stress changes and seismological source parameters.
(2015-04-13); ; ; ; Earthquakes occurring close to hydrocarbon fields under production are often under critical view of being induced or triggered. However, clear and testable rules to discriminate the different events have rarely been developed and tested. The unresolved scientific problem may lead to lengthy public disputes with unpredictable impact on the local acceptance of the exploitation and field operations. We propose a quantitative approach to discriminate induced, triggered and natural earthquakes, which is based on testable input parameters. Maxima of occurrence probabilities are compared for the cases under question, and a single probability of being triggered or induced is reported. The uncertainties of earthquake location and other input parameters are considered in terms of the integration over probability density functions (pdf). The probability that events have been human-triggered/induced is derived from the modeling of Coulomb stress changes and a rate and state dependent seismicity model. In our case a 3D boundary element method has been adapted for the nuclei of strain approach to estimate the stress changes outside the reservoir, which are related to pore pressure changes in the field formation. The predicted rate of natural earthquakes is either derived from the background seismicity or, in case of rare events, from an estimate of the tectonic stress rate. Instrumentally derived, seismological information on the event location, source mechanism and the size of the rupture plane is of advantage for the method. If the rupture plane has been estimated, the discrimination between induced or only triggered events is theoretically possible if probability functions are convolved with a rupture fault filter. We apply the approach to three recent main-shock events: (1) the Mw 4.3 Ekofisk 2001, North Sea earthquake close to the Ekofisk oil field, the 2004 Mw 4.4 Rotenburg, Northern Germany earthquake in the vicinity of the Söhlingen gas field, and the Mw 6.1 Emilia 2012, Northern Italy earthquake in the vicinity of a hydrocarbon reservoir. The three test cases cover the complete range of possible causes: clearly “human-induced”, “not even human-triggered” and a third case in-between both extremes.309 32 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Source modelling of the M5-6 Emilia-Romagna, Italy, earthquakes (May 20-29, 2012)
(2013-03-28); ; ; ; On 2012 May 20 and 29, two damaging earthquakes with magnitudes Mw 6.1 and 5.9, respectively, struck the Emilia-Romagna region in the sedimentary Po Plain, Northern Italy, causing 26 fatalities, significant damage to historical buildings and substantial impact to the economy of the region. The earthquake sequence included four more aftershocks with Mw ? 5.0, all at shallow depths (about 7–9 km), with similar WNW–ESE striking reverse mechanism. The timeline of the sequence suggests significant static stress interaction between the largest events. We perform here a detailed source inversion, first adopting a point source approximation and considering pure double couple and full moment tensor source models. We compare different extended source inversion approaches for the two largest events, and find that the rupture occurred in both cases along a subhorizontal plane, dipping towards SSW. Directivity is well detected for the May 20 main shock, indicating that the rupture propagated unilaterally towards SE. Based on the focal mechanism solution, we further estimate the co-seismic static stress change induced by the May 20 event. By using the rate-and-state model and a Poissonian earthquake occurrence, we infer that the second largest event of May 29 was induced with a probability in the range 0.2–0.4. This suggests that the segment of fault was already prone to rupture. Finally, we estimate peak ground accelerations for the two main events as occurred separately or simultaneously. For the scenario involving hypothetical rupture areas of both main events, we estimate Mw = 6.3 and an increase of ground acceleration by 50 per cent. The approach we propose may help to quantify rapidly which regions are invested by a significant increase of the hazard, bearing the potential for large aftershocks or even a second main shock.428 21 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Towards an improved seismic risk scenario for Bishkek, Kyrgyz Republic
(2011); ; ; ; A risk scenario for Bishkek, capital of the Kyrgyz Republic, is evaluated by considering a magnitude 7.5 earthquake occurring over the Issyk-Ata fault.The intensity values predicted through the application of an attenuation relationship and a recently compiled vulnerability composition model are used as inputs for seismic risk assessment, carried out using the CREST (Cedim Risk Estimation Tool) code. Although the results of this study show a reduction by as much as a factor of two with respect to the results of earlier studies, the risk scenario evaluated in this paper confirms the large number of expected injuries and fatalities in Bishkek, as well as the severe level of building damage. Furthermore, the intensity map has also been evaluated by performing stochastic simulations. The spectral levels of the ground shaking are converted into intensity values by applying a previously derived conversion technique. The local site effects are empirically estimated considering the spectral ratios between the earthquakes recorded by a temporary network deployed in Bishkek and the recordings at two reference sites. Although the intensities computed via stochastic simulations are lower than those estimated with the attenuation relationship, the simulations showed that site effects, which can contribute to intensity increments as large as 2 units in the north part of the town, are playing an important role in altering the risk estimates for different parts of the town.210 2512 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Site effect assessment in Bishkek (Kyrgyzstan) using earthquake and noise recording data
(2010-12); ; ; ; Kyrgyzstan, which is located in the collision zone between the Eurasian and Indo-Australian lithosphere plates, is prone to large earthquakes as shown by its historical seismicity. Hence, an increase in the knowledge and awareness by local authorities and decision makers of the possible consequence of a large earthquake, based on improved seismic hazard assessments and realistic earthquake risk scenarios, is mandatory to mitigate the effects of an earthquake. To this regard, the Central Asia Cross-Border Natural Disaster Prevention (CASCADE) project aims to install a cross- border seismological and strong motion network in Central Asia and to support microzonation activities for the capitals of Kyrgyzstan, Uzbekistan, Kazakhstan, Tajikistan, and Turkmenistan. During the first phase of the project, a temporary seismological network of 19 stations was installed in the city of Bishkek, the capital of Kyrgyzstan. Moreover, single-station noise recordings were collected at nearly 200 sites. In this study, the site amplifications occurring in Bishkek are assessed by analyzing 56 earthquakes extracted from the data streams continuously acquired by the network, as well as from the single-station noise measurements. A broadband amplification (starting at ∼0:1 and 0.2 Hz), is shown by the standard spectral ratio (SSR) results of the stations located within the basin. The reliability of the observed low-frequency amplification was validated through a time–frequency analysis of denoised seismograms. Discrepancies between horizontal-to-vertical spectral ratio and SSR results are due to the large amplification of the vertical component of ground motion, probably due to the effect of converted waves. The single-station noise results, once their reliability was assessed by their comparison with the earthquake data, have been used to produce the first fundamental resonance frequency map for Bishkek, whose spatial variation shows a good agreement with the presence of an impedance contrast within the Tertiary sedimentary cover.190 749 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Seismic input motion determined from a surface-downhole pair of sensors: a constrained deconvolution approach.
(2010-06); ; ; ; Bindi, D.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Milano-Pavia, Milano, ItaliaWe apply a deconvolution approach to the problem of determining the input motion at the base of an instrumented borehole using only a pair of recordings, one at the borehole surface and the other at its bottom. To stabilize the bottom-tosurface spectral ratio, we apply an iterative regularization algorithm that allows us to constrain the solution to be positively defined and to have a finite time duration. Through the analysis of synthetic data, we show that the method is capable of retrieving reliable input motion, suppressing the effect of the negative interference generated by the downgoing waves. Results obtained by applying the methodology to weak earthquakes recorded at the Ataköy (Istanbul) vertical array are also presented and show that removing the effect of the downgoing waves is remarkable, even considering the recording at a depth of 140 m.112 589 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Deblurring of frequency-wavenumber images from small-scale seismic arrays
(2010); ; ; ;Picozzi, M.; GFZ-PotsdamParolai, S.; GFZ-PotsdamTemporary arrays installed in urban areas for investigating the upper-most geological structure typically comprised of a limited number of stations and are arranged in geometries constrained by environmental boundaries. Therefore, it is expected that the frequency–wavenumber images are significantly blurred by the array transfer function and are corrupted by noise. In this paper, the effect of theRichardson–Lucy regularization method applied to the problem of deblurring frequency–wavenumber images is investigated. The images are computed by analysing data from two small-aperture 2-D arrays, installed with different configurations in a test-site within the town of Potenza (Southern Italy) for near-surface investigations. We show that removing the effects of the array response from the frequency–wavenumber images improve the phase-velocity estimation, reducing the relevant level of uncertainty. Furthermore, the Richardson–Lucy regularization method is effective in reducing the level of noise related to spatial aliasing by eliminating spurious peaks, allowing the maxima related to different seismic sources to be better discriminated.144 621 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Determination of shallow S-wave attenuation by down-hole waveform deconvolution: a case study in Istanbul (Turkey)
(2010); ; ; ; The estimation of shear-wave velocity and attenuation in near-surface geology is of primary importance in engineering seismology. In fact, their knowledge is essential for site response studies when preparing improved seismic hazard scenarios. In this study, we propose two approaches for estimating the average shear-wave quality factor Qs by using recordings of a vertical array of accelerometers. The methods are mainly based on the deconvolution of the wavefield recorded in a borehole with that recorded at the surface. The first method requires the Fourier transform of the deconvolved wavefield to be fitted with a theoretical transfer function valid for the vertical or nearly vertical (in the case at hand up to 30° incidence angle) propagation of S-waves. The second method is based on the spectral fitting of the Fourier transform of only the acausal part of the deconvolved wavefield with a theoretical transfer function. Both methods can be applied without any prior knowledge of the subsoil structure (since they are based on empirical data analysis) and do not require a precise knowledge of the azimuthal orientation of the sensors in the boreholes (which is seldom available). First, we describe the theoretical framework of the proposed methodologies for Qs estimation, which are based on the assumption that the structure in the borehole is weakly heterogeneous in the vertical direction (that is, no large impedance contrast exists between the borehole sensor and the surface). Second, by using synthetic accelerograms, we verify that in a realistic subsoil structure, the assumption of vertical homogeneity can hold and we investigate the robustness and the suitability of the proposed methods. Finally, only the method that was shown to provide the more stable results, based on fitting the borehole-to-surface spectral ratio with a theoretical function, is applied to earthquakes signals recorded by a vertical array of accelerometers installed in Ataköy (western Istanbul). Results show that using borehole data provides a fair and robust estimate of an average Qs (of about 30, 46 and 99 for the 0-50, 0-70, 0-140 m depth ranges, respectively), that can be used for numerical simulations of ground motion.135 417 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Empirical H/V spectral ratios estimated in two deep sedimentary basins using microseisms recorded by short-period seismometers
(2009-01-01); ; ; ; In this work, we analyse continuous measurements of microseisms to assess the reliability of the fundamental resonance frequency estimated by means of the horizontal-to-vertical (H/V) spectral ratio within the 0.1–1 Hz frequency range, using short-period sensors (natural period of 1 s). We apply the H/V technique to recordings of stations installed in two alluvial basins with different sedimentary cover thicknesses—the Lower Rhine Embayment (Germany) and the Gubbio Plain (Central Italy). The spectral ratios are estimated over the time–frequency domain, and we discuss the reliability of the results considering both the variability of the microseism activity and the amplitude of the instrumental noise. We show that microseisms measured by short period sensors allow the retrieval of fundamental resonance frequencies greater than about 0.1–0.2 Hz, with this lower frequency bound depending on the relative amplitude of themicroseism signal and the self-noise of the instruments. In particular,we show an examplewhere the considered short-period sensor is connected to instruments characterized by an instrumental noise level which allows detecting only fundamental frequencies greater than about 0.4 Hz. Since the frequency at which the peak of the H/V spectral ratio is biased depends upon the seismic signal-to-instrument noise ratio, the power spectral amplitude of instrumental self-noise should be always considered when interpreting the frequency of the peak as the fundamental resonance frequency of the investigated site.184 458
