Skip to main content
The search returned 9 results
Now showing 1 - 9 of 9
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Comparative Study of CPTU and SDMT in Liquefaction-Prone Silty Sands with Ground Improvement

    Following the 2012 Emilia-Romagna seismic sequence, widespread liquefaction of silty sands was observed, providing the opportunity to enhance our knowledge of the influence of fines content on seismic hazard and mitigation works. This paper presents the results of a thorough geotechnical investigation performed in connection with full-scale controlled blast tests in Bondeno, Italy, a small village that suffered liquefaction in 2012. Piezocone (CPTU) and seismic dilatometer (SDMT) tests were performed in natural and improved soils after rammed aggregate pier (RAP) treatment to a depth of 9.5 m to provide accurate soil characterization, evaluate liquefaction, and verify the effectiveness of the ground improvement. The combined use of piezocone (CPTU) and flat dilatometer (DMT) data provided reliable estimates of the overconsolidation ratio and at-rest earth pressure coefficient and highlighted the soil improvement in silty sands between 4 and 9 m in depth. Shear-wave velocity measurements showed a low sensitivity to RAP installation. The treatment effectiveness was also confirmed by the use of the simplified procedures for liquefaction assessment, underlining the important influence of the adopted fines profile and by the blast-induced liquefaction. CPTU and DMT parameters remained approximately unchanged between the piers after the detonation.
      140  169
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Liquefied sites of the 2012 Emilia earthquake: a comprehensive database of the geological and geotechnical features (Quaternary alluvial Po plain, Italy)

    This paper presents a comprehensive geological and geotechnical study of the whole area affected by liquefaction following the 2012 Emilia earthquakes, including all the available information from the field reconnaissance surveys, in situ tests, and laboratory analyses. The compilation was performed at 120 liquefied sites to verify and validate the reliability of liquefaction charts in alluvial sediments, and to assess liquefaction induced by the 2012 seismic sequence in the Emilia plain. The results reveal a wide range of grain sizes (from clean sands to sandy silts) and compositional characteristics (quartz-rich to litharenitic) in the 2012 ejecta, and show a strong relationship between the liquefaction and stratigraphic architecture of the subsurface. The availability of in situ tests at the liquefied sites makes it possible to verify and validate the reliability of the liquefaction charts in alluvial sediments with respect to the real observations. For the analyzed Emilia case studies, the use of non-liquefiable crust provides better estimations of the liquefaction manifestations when coupled with the thickness of the liquefiable layer rather than with the liquefaction potential index. Altogether, this work makes available to the international scientific community a consistent liquefaction database for in-depth earthquake studies
      237  110
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Remote sensing of induced liquefaction: TLS and SfM for a full scale blast test

    Terrestrial laser scanning (TLS) and drone-based structure-from-motion (SfM) photogrammetry allowed the study of soil de formations due to blast-induced liquefaction during an experiment carried out on 4 June 2018. The research aimed at both evaluating the measurement quality and estimating the rammed aggregate piers (RAPs) effectiveness in mitigating the effects of soil liquefaction. These effects mainly consist of subsidence and deposits of ejected and extruded materials. The comparison between multitemporal 3D models provided surface variation maps and volume changes. In addition, classical topographical leveling allowed the measurement of subsurface vertical displacement along a specific cross section. The results pointed out a significant reduction, higher than 50% of soil deformation in areas improved by RAPs installation; moreover, the corresponding volume variations were no more than about 37% of those occurred in the not improved area. Finally, a critical comparison between remote sensing and leveling suggested that surface variation maps could under-estimate the area lowering up to 15% in this kind of terrain.
      374  49
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Liquefaction Mitigation of Silty Sands Using Rammed Aggregate Piers Based on Blast-Induced Liquefaction Testing

    To investigate the liquefaction mitigation capability of rammed aggregate piers (RAP) in silty sand, blast liquefaction testing was performed at a soil profile treated with a full-scale RAP group relative to an untreated soil profile. The RAP group consisted of 16 piers in a 4 × 4 arrangement at 2 m center-to-center spacing extending to a depth of 9.5 m. Blasting around the untreated area induced liquefaction (ru ≈ 1.0) from a 3 to 11 m depth, producing several large sand boils and causing a settlement of 10 cm. In contrast, the installation of the RAP group reduced excess pore water pressure (ru ≈ 0.75), eliminated sand ejecta, and reduced the average settlement to between 2 and 5 cm when subjected to the same blast charges. Although the liquefaction-induced settlement in the untreated area could be accurately estimated using an integrated cone penetration test (CPT)-based settlement approach, settlement in theRAPtreated area was significantly overestimated with the same approach, even after considering RAP treatment-induced densification. Analyses indicate that settlement after RAP treatment could be successfully estimated from liquefaction-induced compression of the sand and RAP acting as a composite material. This test program identifies a mechanism that explains how the settlement was reduced for the RAP group despite the elevated ru values in the silty sands that are often difficult to improve with vibratory methods.
      44  1
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    A New Dynamic Cone Penetration Test–Based Procedure for Liquefaction Triggering Assessment of Gravelly Soils

    Developing a reliable, cost-effective liquefaction triggering procedure for characterizing the liquefaction potential of gravelly soils based on in situ penetration testing has always been a great challenge for geotechnical engineers and researchers. Typical correlations based on the standard penetration test (SPT) and the cone penetration test (CPT) are affected by large-size gravel particles, which can lead to erroneous results. The Becker Penetration Test, well known for gravelly soil characterization, is cost-prohibitive for routine projects and is not available in most of the world. With a cone diameter of 74 mm the Chinese dynamic cone penetration test (DPT) is superior to smaller penetrometers and can be economically performed with conventional drilling equipment. DPT has previously been directly correlated to field performance data, and probabilistic liquefaction resistance curves were developed based on one earthquake and geologic environment in China; however, the use of these data in other tectonic and geologic environments was not validated. In this study, 137 data points from 10 different earthquakes and different depositional environments in seven countries have been used to develop probabilistic liquefaction resistance curves. The data set was expanded by performing DPT soundings at sites around the world where gravelly soil did or did not liquefy in past earthquakes. Based on the expanded DPT database, a new set of magnitude-dependent probabilistic triggering curves has been developed using logistic regression analysis. The new triggering curves are better constrained by data and the spread between the 85% and 15% probability curves is reduced. Liquefaction resistance is shifted upward at lower DPT values. A new magnitude scaling factor (MSF) curve has also been developed specifically for gravel liquefaction which was found to be consistent with previous curves for sand.
      38  1
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Blast-induced liquefaction in silty sands for full-scale testing of ground improvement methods: Insights from a multidisciplinary study

    In the engineering geology field increased attention has been posed in recent years to potential liquefaction mitigation interventions in susceptible sand formations. In silty sands this is a major challenge because, as the fines content increases, vibratory methods for densification become progressively less effective. An alternative mitigation technique can be the installation of Rammed Aggregate Pier® (RAP) columns that can increase the resistance of the soil, accounting for its lateral stress increase and for the stiffness increase from soil and RAP composite response. To investigate the influence of these factors on liquefaction resistance, full-scale blast tests were performed at a silty sand site in Bondeno (Ferrara, Italy) where liquefaction was observed after the 2012 Emilia-Romagna earthquake. A multidisciplinary team of forty researchers carried out devoted experimental activities aimed at better understanding the liquefaction process at the field scale and the effectiveness of the treatment using inter-related methods. Both natural and improved areas were investigated by in-situ tests and later subjected to controlled blasting. The blast tests were monitored with geotechnical and geophysical instrumentation, topographical surveying and geological analyses on the sand boils. Results showed the RAP effectiveness due to the improvement of soil properties within the liquefiable layer and a consequent reduction of the blast-induced liquefaction settlements, likely due to soil densification and increased lateral stress. The applied multidisciplinary approach adopted for the study allowed better understanding of the mechanism involved in the liquefaction mitigation intervention and provided a better overall evaluation of mitigation effectiveness
      2078  132
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Gravel Liquefaction Assessment Using the Dynamic Cone Penetration Test Based on Field Performance from the 1976 Friuli Earthquake

    The dynamic cone penetration test (DPT) developed in China has been correlated with liquefaction resistance of gravelly soils based on field performance data from theMw7.9Wenchuan earthquake.With a diameter of 74 mm, DPT would be less sensitive to gravel size particles than the SPT or CPT and could be a viable assessment tool depending on gravel size and percentage. In this study, liquefaction resistance is evaluated using four DPT soundings with two hammer energies and shear wave velocity (VS) measurements in Avasinis, Italy, where gravelly sand liquefied in the 1976 Friuli, Italy, earthquake. The DPT correctly predicted liquefaction at three sites where liquefaction was observed; however, it also predicted liquefaction in a highly stratified silt and silty gravel profile where ejecta was not observed. This failure appears to be a result of the “system response” of the profile, which impeded ejecta as identified at similar stratified sites in New Zealand. VS1-based triggering curves often predicted no liquefaction at sites where liquefaction was observed, suggesting that the boundary curves may need to shift to the right for gravelly soils. Standard SPT energy corrections were found to be reasonable for the DPT.
      285  3
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Liquefaction source layer for sand blows induced by the 2016 megathrust earthquake (Mw 7.8) in Ecuador (Boca de Briceño)

    Numerous sand boils were generated in the alluvial plain at the mouth of the Rio Brice˜no valley (Ecuador) during the Mw 7.8 earthquake of April 2016. The area is characterized by a series of raised marine terraces formed as a consequence of the rapid tectonic coastal uplift during the Quaternary. Boreholes and geotechnical investigations were carried during post-earthquake surveys and for the purpose of mitigating the liquefaction effects. Five lithological units were identified at a site of embankment, which represented continental-marine and transitional sedimentation since the Last Glacial Maximum. A comprehensive study of texture and petrographic composition of sand boils has been performed and compared with sandy silts and silty sands of the buried sedimentary sequence in order to identify the source levels for liquefaction. The petrographic components, in particular the low content of bioclasts and carbonate fragments of the sand boils, allow to pinpoint a source layer made up of fine-grained silty sands located between 2 and 4.5 m depth (Unit 2) whereas the deeper marine sands, richer in bioclasts, were not involved. The results support the idea that earthquake-induced liquefaction phenomena are not restricted to clean sands and well-sorted deposits, but may affect sand layers with significant amount of nonplastic silt.
      202  63
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    The first Italian blast-induced liquefaction test (Mirabello, Emilia-Romagna, Italy): description of the experiment and preliminary results

    Soil liquefaction can result in significant settlement and reduction of load-bearing capacity. Moreover, the generation of pore pressure during an earthquake and its post-seismic dissipation can generate permanent deformations and settlements. The quantitative evaluation of post-liquefaction settlements is of extreme importance for engineering purposes, i.e. for earthquake-resistant design of new buildings and safety evaluation of existing ones. Quantifying the extent of these phenomena is, however, rather difficult. Uncertainties arise from the stochastic nature of the earthquake loading, from the simplifications of soil models, and from the difficulty in establishing correlations between the pre-earthquake soil state and the post-seismic deformations. Field scale liquefaction tests, under controlled conditions, are therefore important for a correct quantification of these phenomena. Recent experiences (e.g. New Zealand, United States) show that liquefaction can be induced and monitored with field scale blast tests to study the related effects on soil geotechnical properties. Within this framework this paper introduces the preliminary results obtained from a research project on blast-induced liquefaction at field scale. Tests were performed at a trial site located in Mirabello (Ferrara, Italy), a village strongly affected by liquefaction phenomena during the 2012 Emilia Romagna earthquake. Invasive tests, such as piezocone, seismic dilatometer and down-hole tests, and non-invasive tests were carried out before and after the execution of two blast test sequences to study the variation in physical properties of the soils. Pore pressure transducers, settlement profilometers and accelerometers were installed with the objective of measuring, during and after the detonations, the generation and subsequent dissipation of the pore pressure, the vertical deformations, and the blast-induced ground motions respectively. Variations in load distribution on deep foundations due to soil liquefaction were also evaluated on a test micropile instrumented with a strain gauge array. Topographical surveys were carried out to measure ground surface settlements. Laboratory tests and trenches also provided increased understanding of the site characteristics.
      1606  185