Skip to main content
The search returned 14 results
Now showing 1 - 10 of 14
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    New insights into earthquake precursors from InSAR

    We measured ground displacements before and after the 2009 L’Aquila earthquake using multitemporal InSAR techniques to identify seismic precursor signals. We estimated the ground deformation and its temporal evolution by exploiting a large dataset of SAR imagery that spans seventy-two months before and sixteen months after the mainshock. These satellite data show that up to 15 mm of subsidence occurred beginning three years before the mainshock. This deformation occurred within two Quaternary basins that are located close to the epicentral area and are filled with sediments hosting multi-layer aquifers. After the earthquake, the same basins experienced up to 12 mm of uplift over approximately nine months. Before the earthquake, the rocks at depth dilated, and fractures opened. Consequently, fluids migrated into the dilated volume, thereby lowering the groundwater table in the carbonate hydrostructures and in the hydrologically connected multi-layer aquifers within the basins. This process caused the elastic consolidation of the fine-grained sediments within the basins, resulting in the detected subsidence. After the earthquake, the fractures closed, and the deep fluids were squeezed out. The pre-seismic ground displacements were then recovered because the groundwater table rose and natural recharge of the shallow multi-layer aquifers occurred, which caused the observed uplift.
      417  5
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Synthetic Aperture Radar (SAR) Doppler Anomaly Detected During the 2010 Merapi (Java, Indonesia) Eruption

    (2013) ; ; ; ;
    de Michele, M.; BRGM
    In this letter, we report the presence of a localized Doppler anomaly occurring during the focusing of a Radarsat-2 data set acquired on the Merapi volcano (Indonesia) during the devastating 2010 eruption. The Doppler anomaly is manifested as ∼3-km-wide bull’s-eye-shaped azimuth pixel shifts between two subaperture images. The Doppler anomaly is centered on the summit-south flank of the Merapi volcano. The pixel shifts reach up to 11.6 m. Since the Merapi volcano was undergoing a large eruption during the data acquisition, it is possible that there is a volcano-related phenomenon that has delayed the radar signal so much to create measurable pixel offsets within a single synthetic aperture radar (SAR) data set, similar, but more extensive, to the signal generated by targets motions; similar, but less extensive, to the signal generated by ionospheric perturbations. It is known that the SAR signal is delayed as it passes through heterogeneous layers of the atmosphere, but this delay typically affects the SAR signal to a fraction of the phase cycle or few centimeters depending on the radar wavelength employed by the system. We investigate the source of this anomalous metric signal; we review the theoretical basis of SAR image focusing, and we try to provide a consistent physical framework to our observations. Our results are compatible with the SAR signal being perturbed during the actual process of image focusing by the presence of a contrasting medium located approximately between 6- and 12.5-km altitude, which we propose being associated with the presence of volcanic ash plume.
      143  17
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    DEM OF THE VENETO PLAIN BY ERS2-ENVISAT CROSS-INTERFEROMETRY

    (Emilia-Romagna Region - Geological Seismic and soil Survey, 2012-06-12) ; ; ; ;
    Digital Elevation Models (DEMs) of flat lowlying coastlands are becoming even more important for environmental risk analyses, for example the development of effective plans for flooding protection. The need of information at high spatial resolution over very large areas, of the order of 100×100 km2, practically precludes the use of traditional methods (e.g., leveling and DGPS) due to their intrinsic limitation in covering wide zones and reduces the possibility of using Lidar because of its high cost. Starting from the last decade, space-borne radar sensors have been used extensively for this purpose. The most known is the SRTM (Shuttle Radar Topographic Mission) DEM which covers most of the land area between ±60° latitude. This DEM was generated using singlepass interferometry and is widely available at 3-arc-seconds. In this work, we present the results obtained for the Veneto plain, Italy, using the spaceborne SAR (Synthetic Aperture Radar) crossinterferometry.
      211  315
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    The April 3, 2010 earthquake along the Pernicana fault (Mt. Etna - Italy): analysis of satellite and in situ ground deformation data integrated by the SISTEM approach

    Etna is worldwide known as one of the most studied and monitored active volcanoes. Flank instability along the eastern and southern portion of Mt. Etna has been observed and measured thanks to geodetic networks and InSAR data analysis. The spreading area is bordered to the north by the east-west Pernicana Fault System (PFS) which dynamic is often linked with the eruptive activity, as recently observed during the 2002-2003 eruption. A seismic sequence occurred since April 2-3, 2010, along the PFS with two very shallow (a few hundred meters) mainshocks of magnitude 3.6 and 3.5. Explosions and ash emissions at the summit craters followed this swarm and culminated some days later (April 7-8). Just after the earthquake, specific GPS surveys were carried out aimed at monitoring the eastern part of the Pernicana fault, and the leveling route on the northeastern flank of the volcano was also surveyed. Trying to investigate the deformation occurred along the PFS during the events of April 3rd 2010, we performed a DInSAR (Differential Interferometric Synthetic Aperture Radar) analysis of ascending and descending Envisat, and of ascending ALOS-PALSAR images encompassing the date of the earthquake. The Envisat interferograms show very intense but local deformation on the Envisat ascending data and a low signal for the descending geometry, close to the Pernicana fault trace. This is probably due to the oblique normal/leftlateral kinematics of the PFS (as deduced also by GPS and leveling data), indeed both vertical (lowering) and horizontal (eastwards) components of motion produce a strong stretching of the LOS (Line Of Sight) distance for ascending geometry, while the two components act in opposite ways for the descending geometry, resulting in lower LOS distance variations compared to the ascending data set. We analyzed also the ALOS pair referring to 21/02/2010 – 08/04/2010 time and acquired along the ascending track number 638. The ALOS interferogram clearly show three fringes corresponding to roughly 35 cm of LOS displacement. The preliminary modeling of the interferograms agree with the seismic information (very shallow faulting, seismic moment) and show that the medium behave elastically. In order to investigate the ground deformation pattern associated with this event, an application of the novel SISTEM (Simultaneous and Integrated Strain Tensor Estimation from geodetic and satellite deformation Measurements) approach is presented here. To achieve higher accuracy and get better constraint of the 3D components of the displacements, we improved the standard formulation of SISTEM approach, based on the GPS and a single DInSAR sensor, in order to take into account all the available dataset (GPS, leveling, ascending and descending ENVISAT C-Band interferograms and the ALOS L-Band data). The 3D displacement maps obtained using the SISTEM approach well show the kinematics of the PFS, and are able to reconstruct also the ground deformation affecting the whole investigated area, defining the movements of the north-eastern flank of the volcano. These results, which provide an accurate spatial characterization of ground deformation, are hence promising for future studies aimed at improving the knowledge about the kinematics of the active faults of Mt. Etna.
      420  300
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Analysis of satellite and in situ ground deformation data integrated by the SISTEM approach: the April 3, 2010 earthquake along the Pernicana fault (Mt. Etna - Italy) case study

    Etna is known worldwide as one of the most studied and monitored active volcanoes. Flank instability along the eastern and southern portion of Mt. Etna has been observed and measured thanks to geodetic networks and InSAR data analysis. The spreading area is bordered to the north by the east-west Pernicana Fault System (PFS) whose dynamics is often linked with the eruptive activity, as recently observed during the 2002-2003 eruption. A seismic sequence occurred from April 2-3, 2010, along the PFS with very shallow (a few hundred meters) mainshocks of magnitude 4.3 and 3.6. Explosions and ash emissions at the summit craters followed this swarm culminating a few days later (April 7-8). Despite their small magnitude, the earthquakes caused damage and significant surface fracturing along the PFS. In order to investigate and measure the deformations in the near field of the earthquakes, the SISTEM integration approach has been exploited. The SISTEM enabled integrating geodetic in situ ground deformation measurements (GPS and Levelling) with satellite interferometric measurements (ENVISAT and ALOS), in order to obtain high resolution 3D displacement maps, allowing to overcome the limitations of each technique and take advantage of the particular features of each of them. The integrated ground deformation field evidenced that the medium behave elastically. We inverted the SISTEM results using an optimization algorithm based on the Genetic Algorithm (GA) in order to model the kinematics of the PFS associated to seismic swarm; the results are in good agreement with the field evidence and improved the knowledge on the kinematics of the PFS and Mt. Etna’s unstable flank.
      282  39
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    SAFER Response to Eyjafjallajökull and Merapi Volcanic Eruptions. In: ‘Let's embrace space’ Space Research achievements under the 7th Framework Programme, Edit by European Commission, DG Enterprise and Industry

    After PREVIEW FP6 Project’s conclusion, the WP30210 within FP7 GMES SAFER (Services and Applications For Emergency Response) Project has the main objective to refine and consolidate the Earthquake & Volcanoes (E&V) services that were just tested in previous activities and to provide operative services to Users, the Civil Protection Authorities. Here we mainly report objectives and results for the specific tasks related to Eruptive volcanic parameters (WP30211). Four specific products related to the volcanic events which will contribute to the monitoring of the phenomena and mitigation of the eruption effects are expected within the end of the Project. They mainly concern: SAR displacement, high temperature events (HTE), Ash detection, SO2 concentration and flux, and Ash dispersion models. In particular, here we mostly focus on the activity performed in the occasion of FP7 GMES SAFER activation during two major volcanic eruptions occurred in 2010. The first activation was for the Eyjafjallajökull eruption occurred in Iceland between April and May 2010, and the second one was solicited in the occasion of the eruption of Mount Merapi (Indonesia) in October-November 2010. Here we present the results of both remote sensing and modeling activities performed during these two events.
      408  259
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Subsidence induced by urbanisation in the city of Rome detected by advanced InSar technique and geotechnical investigations

    We applied the Interferometric Point Target Analysis (IPTA) technique to study the city of Rome (Italy) aiming to detect and measure the surface movements of buildings and urban structures. The available SAR dataset has been delivered by ESA CAT1 3258 and ranges the period 1992–2005. In particular ERS1–ERS2 data processed covers 1995–2000, while Envisat ASAR 2002–2005. The Point Target velocity map shows a general stability except for some very local areas affected by subsidence rate larger than 10 mm/year. The analysis of the time series, compared to a detailed geological and geotechnical investigation of the lithostratigraphy of the alluvial sediments of the Tiber River, and combined with a temporal reconstruction of the expansion of the city over the alluvial valleys, allowed us to depict the main factors controlling the observed subsidence. These are: the in situ effective stress conditions, the related compressibility and viscous characteristics of the loaded soils, the thickness of the compressible stratum, the time since loading instant, and the entity of loading. Furthermore the observed subsidence is time-dependent, even at a long time-scale, with respect to the age of the buildings being most of the buildings constructed since the '50s still affected by slow subsidence. We mainly focused on the Grottaperfetta stream valley that is characterized by an anomalous high and time-lasting subsidence. Original data on the lithostratigraphic setting of this alluvial valley indicate that the high subsidence rate measured up to 2005 is caused by a still active primary consolidation process.
      284  53
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    ERS AND ENVISAT SAR INTERFEROMETRY TO MEASURE LAND SUBSIDENCE IN THE VENICE LAGOON ON NATURAL AND ARTIFICIAL POINT TARGETS

    (ESA Communication Production Office ESTEC, Noordwijk, The Netherlands, 2007-04-23) ; ; ; ;
    The Venice Lagoon, Italy, is a unique worldwide environment which is presently vulnerable due to loss in surface elevation as a result of land subsidence referred to the mean sea level. Land displacements in the Venice coastland have been determined over time by traditional monitoring techniques (i.e., spirit leveling and GPS). Recently, SAR-based analyses have been used to complement the ground-based methods. Interferometric analysis on persistent point targets has been proved to be very effective in detecting land displacement in the coastal environment. ERS SAR and ENVISAT ASAR images spanning the time period 1992-2005 and 2003- 2006, respectively, have been processed at regional and local scale and on “natural” as well as “artificial” reflectors.
      243  234
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    SAR Interferometry for ground vertical displacement of small islands in the Venice Lagoon: the case of Murano Island

    (CORILA, Venezia; Stampa “Multigraf” Spinea (ITA), 2005) ; ; ; ;
    Strozzi, Tazio
    Our knowledge of the dynamics of vertical ground movements plays a fundamental role in the study of the geomorphological processes, particularly for determining sediment deposition and erosion causes. The conservation of lagoon morphological structures such as salt marshes and tidal flats, besides erosion due to waves and currents, depends on their surface height with respect to the sea level that, for short periods, is primarily related to the land subsidence process and secondarily to eustasy. Ground vertical variations with respect to the sea level, even if small, can, in fact, trigger sediment erosion and deposition processes. To determine land displacement rates in small islands of the Venice Lagoon not covered by traditional surveys (levelling and differential GPS), SAR-based monitoring techniques, i.e. differential SAR interferometry (INSAR) and interferometric point target analysis (IPTA) from ERS-1 and ERS-2 satellites, were performed. We will use the Murano Island for our example in this contribution.
      106  246
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    SAR Interferometric Point Target analysis and application to the monitoring of land subsidence in the Venice Lagoon

    (Shanghai Scientific & Technical Publishers, 2005) ; ; ; ;
    In the Interferometric Point Target Analysis (IPTA) point-like targets that remain phase coherent over time are identified in a sequence of satellite Synthetic Aperture Radar (SAR) images and used to estimate the progressive deformation ofthe terrain with millimetric accuracy. Building upon conventional interferometric SAR techniques, IPT A overcomes atrnospheric delay anomalies and tempora! and geometrie decorrelation by exploring the tempora! and spatial characteristics of radar interferometric signatures collected from point targets widely available over urban areas but that can be also found scattered outside cities and villages. In this contribution the application of IPT A to the monitoring of land' subsidence in the urban and littoral environments of the Venice Lagoon is described. The results achieved using ali the available ERS SAR images acquired between 1992 and 2000 are very significant due to the achieved target spatial and tempora! coverage.
      154  240