Skip to main content
The search returned 84 results
Now showing 1 - 10 of 84
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    High resolution seismic tomography across the 1980 (Ms 6.9) Southern Italy earthquake fault scarp

    A high-resolution multi-fold wide-angle seismic survey conducted across the Irpinia fault, Southern Italy, yields new information about the shallow structure of this normal fault that was reactivated in 1980. The fault zone was imaged to a depth of about 60 m by using a non-linear tomographic technique that is specially designed to image strongly heterogeneous media. The tomographic image confirms the location of the fault, as previously inferred by a trench excavated in warped soft soils, and clearly delineates a step in the bedrock, that is 30-35 m deeper in the hanging wall than in the footwall. This step is indicative of a narrow fault zone, which corresponds upward to the warped soils exposed in the trench, thus demonstrating that the near-surface warping is directly related to a brittle faulting in the bedrock. Assuming that the vertical slip rate yielded by paleoseismic data (0.25-0.35 mm/yr) has been constant since the fault’s inception, the latter should date back to about 100-140 kys ago. Such a young age, along with the small amount of cumulative slip imaged by tomography, may explain why the Irpinia fault is not associated with evident, large-scale geomorphic indicators of its activity.
      202  28
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Results from shallow geophysical investigations in the northwestern sector of the island of Malta

    We performed geophysical investigations in the northwestern sector of the island of Malta to reconstruct velocity-depth models and provide shear-wave velocity profiles. We have chosen two sites, one located in Rabat (Malta) and another in the Golden Bay area. We used both active (seismic and electrical 2D-tomography, Multichanel Analysis of Surface Waves – MASW) and passive (2D arrays and single-station measurements using ambient noise) geophysical methods. Consistently with previous studies performed in this part of Malta, we have found that both sites are characterised by site resonance in the frequency range 1-2 Hz as an effect of the local lithostratigraphic succession that shows an impedance contrast at about 60-90 m depth. This resonance effect can have important implications on both seismic hazard as well as seismic risk evaluation of the region since the amplified frequency range coincides with the resonance frequencies typical of 5–10 storey buildings which are very diffuse in the Maltese Islands, especially after intense recent urbanization.
      1246  10
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Surface ruptures database related to the 26 December 2018, MW 4.9 Mt. Etna earthquake, southern Italy

    We provide a database of the surface ruptures produced by the 26 December 2018 Mw 4.9 earthquake that struck the eastern flank of Mt. Etna volcano in Sicily (southern Italy). Despite its relatively small magnitude, this shallow earthquake caused about 8 km of surface faulting, along the trace of the NNW-trending active Fiandaca Fault. Detailed field surveys have been performed in the epicentral area to map the ruptures and to characterize their kinematics. The surface ruptures show a dominant right-oblique sense of displacement with an average slip of about 0.09 m and a maximum value of 0.35 m. We have parsed and organized all observations in a concise database, with 932 homogeneous georeferenced records. The Fiandaca Fault is part of the complex active Timpe faults system affecting the eastern flank of Etna, and its seismic history indicates a prominent surface-faulting potential. Therefore, this database is essential for unravelling the seismotectonics of shallow earthquakes in volcanic areas, and contributes updating empirical scaling regressions that relate magnitude and extent of surface faulting.
      4586  94
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Liquefaction phenomena associated with the Emilia earthquake sequence of May-June 2012 (Northern Italy)

    (2013)
    Emergeo, Working Group
    ;
    ; ; ;
    In this paper we present the geological effects induced by the 2012 Emilia seismic sequence in the Po plain. Extensive liquefaction phenomena were observed over an area of ~1200 km2 following the May 20, Ml 5.9 and May 29, Ml 5.8 mainshocks, both occurred on about E-W trending, S dipping blind thrust faults. We collected the coseismic geological evidence through field and aerial surveys, reports from local people and web-based survey. On the basis of their morphologic and structural characteristics we grouped the 1362 effects surveyed into three main categories: liquefaction (485), fractures with liquefaction (768), fractures (109). We show that the quite uneven distribution of liquefaction effects, that appear concentrated and aligned, is mostly controlled by the presence of paleo-river beds, out-flow channels and fans of the main rivers crossing the area; these terrains are characterized by the pervasive presence of sandy layers in the uppermost 5 m, a local feature that, along with the presence of a high water table, greatly favours liquefaction. We also find that the maximum distance of observed liquefaction from the earthquake epicentre is ~30 km, in agreement with the regional empirical relations available for the Italian Peninsula. Finally, we observe that the contour of the liquefaction observations has an elongated shape almost coinciding with the aftershock area, the InSAR deformation area, and the I≥6 EMS area. This observation confirms the control of the earthquake source on the liquefaction distribution, and provides useful hints in the perspective of the characterization of the seismogenic source responsible for historical and pre-historical liquefactions.
      1792  745
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Evolution of the late Quaternary San Gregorio Magno tectono-karstic basin (southern Italy) inferred from geomorphological, tephrostratigraphical and palaecological analyses: tectonic implications

    The Pantano di San Gregorio Magno is a 4.7 km 2 large tectono-karstic basin located in the axial belt of the Southern Apennines, an area affected by intense seismicity. The basin was formed in the Middle Pleistocene and is presently undissected. It is filled by lacustrine sediments (clays, silts and pyroclastic sands) passing laterally into alluvial fan deposits. Geomorphological investigations were integrated with tephrostratigraphical, palynological and palaeoecological analyses of a 61 m thick core (not reaching the bedrock). The multiproxy analysis of the S. Gregorio Magno record shows that, over the last 200k yr, the basin hosted a freshwater lake with an oscillating level. Age constraints provided by the tephrostratigraphic record allowed estimation of the sedimentation rate, which varied strongly through time. Evolution of the basin resulted from the complex combination of tectonic subsidence, karst processes and changing amounts of sedimentary inputs. The latter was influenced by allogenic contributions related both to primary and reworked volcanoclastic inputs and was climate-driven. The overall evidence, which indicates that in the long-term the accumulation rate substantially counterbalanced the accommodation space created by faulting, suggests that the basin evolution was also modulated by changing subsidence rates.
      214  28
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Bollettino Sismico Italiano: Analisys of Early Aftershocks of the 2016 MW 6.0 Amatrice, MW 5.9 Visso and MW 6.5 Norcia earthquakes in Central Italy

    The Amatrice-Visso-Norcia seismic sequence is the most important of the last 30 years in Italy. The seismic sequence started on 24 August, 2016 and still is ongoing in central Apennines. At the end of February 2017 more than 57,000 events were located, 80,000 events up to the end of September 2017 (Fig. 1). The mainshocks of the sequence occurred on 24 August 2016 (Mw 6.0 and Mw 5.4), 26 October 2016 (Mw 5.4 and Mw 5.9), 30 October 2016 (Mw 6.5), 18 January 2017 (four earthquakes Mw≥ 5.0). In this seismic sequence, all the waveforms recorded by temporary stations deployed by the SISMIKO emergency group (stations T12**; Moretti et al., 2016) where available in real- time at the surveillance room of INGV. Because of the high level of seismicity and the dense seismic network installed in the region, more than 150 events per day were located at the end of February 2017; still 60 events per day were located up to the end of August 2017.The Amatrice-Visso-Norcia is the most important seismic sequence since 2015, the time when the analysis procedures of the BSI group (Bollettino Sismico Italiano) were revised (Nardi et al., 2015). BSI is now available every four months on the web: bulletins contain revised earthquakes (location and magnitude) with ML≥ 1.5, quasi-real time revision of ML≥ 3.5 earthquakes and phase arrivals from waveforms recorded on seismic stations available from the European Integrated Data Archive (EIDA), (Mazza et al., 2012). These last procedures allow the integration of signals from temporary seismic stations (Moretti et al., 2014) installed by the emergency group SISMIKO (Moretti and Sismiko working group, 2016), even when they are not in real time transmission, if they are rapidly archived in EIDA, together with real time signals from the seismic stations of the permanent INGV network. The analysis strategy of the BSI group for the Amatrice -Visso - Norcia seismic sequence (AVN.s.s in the following) was to select the earthquakes located in the box with min/max latitude: 42.2/43.2 - and min/max longitude: 12.4/14.1 to prepare a special volume of BSI on the seismic sequence.
      334  280
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    High-resolution geophysical investigations in the central Apennines seismic belt (Italy): Results from the Campo Felice tectonic basin

    The Campo Felice basin, in the central Apennines seismic belt (Italy), developed in the hangingwall of a 30 km-long system of NW-trending normal faults with Holocene paleoseismic activity and potential sources of M 6–7 earthquakes. We provide the first subsurface images of a key portion of the basin bounded by the Mt. Cefalone fault along two intersecting profiles trending NNE-SSW (CF-Dip, 1195 m-long) and WNW-ESE (CF-Strike, 1315-m long). We combined high-resolution depth-migrated reflection sections with P-wave velocity and electrical resistivity tomography models. CF-Dip profile displays a wedge-like syn-tectonic sedimentary sequence of alluvial and glacial deposits with Vp ∼ 2500–3000 m/s and resistivity > 500 Ωm in the hangingwall of Mt. Cefalone fault, overlying a high-Vp (>4000 m/s) limestone bedrock ∼ 300 m deep. The whole sequence displays reflectors truncated by the Mt. Cefalone fault zone and subsidiary antithetic faults. CF-Strike profile, tied to three 80–110 m-deep boreholes, shows a thick fluvio-lacustrine sequence with low-Vp (<2000 m/s) and low resistivity (<100 Ωm), and a bedrock that deepens to the southeast (>450 m). Single-station ambient noise measurements display Horizontal to Vertical Spectral Ratios with peaks at ∼1 Hz, decreasing to ∼0.8 Hz to the southeast in agreement with the bedrock deepening indicated by seismic profiling. According to our results, the Campo Felice basin is a deep asymmetric half-graben controlled by faulting whose activity likely started before the Middle Pleistocene. Our minimum displacement estimate accrued in the past 0.5 Ma by the Mt. Cefalone fault is in the range of ∼100–250 m.
      342  59
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Combining 3‐D Deep Electrical Resistivity Tomography With Magnetic Surveys to Investigate Complex Tectonic Basins: A Case Study From the Central Apennines Seismic Belt (Italy)

    (Washington, D.C. : American Geophysical Union, European Geophysical Society, 2025-08-28) ; ; ; ;
    We use an innovative geophysical approach to reconstruct the deep structure of Campo Felice, an important extensional basin in the centrai Apennines (ltaly) where active crustal extension is accommodated by nonna! fauJts capable of generating earthquakes of magnitude Mw 6+. To this end, we combine 3-D Deep Electrical Resistivity Tomography with Unmanned Aerial Vehicle aeromagnetic survey. Before this study, the knowledge of the subsurface was limited to a small sector of the basin investigated by two seismic reflection profiles and shallow scientific drillings. Our resistivity model unravels for the first time a complex subsurface structure, due to two SW-dipping and left-stepping norma! faults (Mt Cefalone­Serralunga and Mt Orsello), with antithetic and relay faults. Altogether, they favored the generation of two distinct sub-basins ~400--450 and ~250-300 m-deep, filled with alluvial, lacustrine and glacial deposits. Aeromagnetic data further constrain the extent and thickness of fine-grained infili sediments, while previous drillings and seismic reflection profiles are useful to constrain geologica! interpretation. We provide a model of basin evolution covering approximately the last million years, improving the knowledge of the Quatemary kinematics and structure of this sector of the chain. Furthermore, th.is cost-effective approach can be safely exported to similar tectonic contexts elsewhere.
      10  37
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Geometry and evolution of a fault-controlled Quaternary basin by means of TDEM and single-station ambient vibration surveys: The example of the 2009 L'Aquila earthquake area, central Italy

    We applied a joint survey approach integrating time domain electromagnetic soundings and single-station ambient vibration surveys in the Middle Aterno Valley (MAV), an intermontane basin in central Italy and the locus of the 2009 L’Aquila earthquake. By imaging the buried interface between the infilling deposits and the top of the pre-Quaternary bedrock, we reveal the 3-D basin geometry and gain insights into the long-term basin evolution. We reconstruct a complex subsurface architecture, characterized by three main depocenters separated by thresholds. Basin infill thickness varies from ~200–300m in the north to more than 450m to the southeast. Our subsurface model indicates a strong structural control on the architecture of the basin and highlights that the MAV experienced considerable modifications in its configuration over time. The buried shape of the MAV suggests a recent and still ongoing predominant tectonic control by the NW-SE trending Paganica-San Demetrio Fault System (PSDFS), which crosscuts older ~ENE and NNE trending extensional faults. Furthermore, we postulate that the present-day arrangement of the PSDFS is the result of the linkage of two previously isolated fault segments. We provide constraints on the location of the southeastern boundary of the PSDFS, defining an overall ~19 km long fault system characterized by a considerable seismogenetic potential and a maximum expected magnitude larger than M6.5. This study emphasizes the benefit of combining two easily deployable geophysical methods for reconstructing the 3-D geometry of a tectonically controlled basin. Our joint approach provided us with a consistent match between these two independent estimations of the basin substratum depth within 15%.
      678  246
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Surface ruptures following the 30 October 2016 Mw 6.5 Norcia earthquake, central Italy

    We present a 1:25,000 scale map of the coseismic surface ruptures following the 30 October 2016 M-w 6.5 Norcia normal-faulting earthquake, central Italy. Detailed rupture mapping is based on almost 11,000 oblique photographs taken from helicopter flights, that has been verified and integrated with field data (>7000 measurements). Thanks to the common efforts of the Open EMERGEO Working Group (130 people, 25 research institutions and universities from Europe), we were able to document a complex surface faulting pattern with a dominant strike of N135 degrees-160 degrees (SW-dipping) and a subordinate strike of N320 degrees-345 degrees (NE-dipping) along about 28km of the active Mt. Vettore-Mt. Bove fault system. Geometric and kinematic characteristics of the rupture were observed and recorded along closely spaced, parallel or subparallel, overlapping or step-like synthetic and antithetic fault splays of the activated fault systems, comprising a total surface rupture length of approximately 46km when all ruptures were considered.
      6034  219