Skip to main content
The search returned 37 results
Now showing 1 - 10 of 37
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    AdriaArray temporary deployment in the Po Plain and Sardinia (Italy)

    (Bologna : INGV, Istituto nazionale di geofisica e vulcanologia, Sezione di Bologna, 2010-, 2025-11-05) ; ; ; ;
    We present the deployment and performance of 17 temporary broadband seismic stations installed in Northern Italy and Sardinia as part of the AdriaArray project. These stations aim to densify the national seismic network, especially in areas with historically sparse coverage such as the Po Plain and Sardinia. We describe here the network design and site selection that follow high-quality standards developed during previous large-scale European seismic experiments. Despite challenging environmental and anthropogenic conditions, the stations recorded high-quality data, enabling both local and teleseismic event detection. We analyze the seismic noise characteristics across the network using probabilistic power spectral densities and observe that stations installed in sedimentary basins typically show higher noise levels at short periods, while stations in rock sites-especially in Sardinia-generally perform better. The use of different sensor types and installation methods also influences noise behavior, particularly in the long-period components. Despite the diverse conditions, the stations allow for the recording of both local and teleseismic events. The addition of the 4P stations improves the network's detection threshold by approximately 0.4 magnitude units in Sardinia and 0.2 in the North Italy. The open-access data from this deployment contribute to AdriaArray's broader goals of advancing seismic imaging and geodynamic interpretation in the Mediterranean region.
      18  28
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    DIVEnet: a local seismographic network monitoring the lower continental crust drilling activities for the ICDP‑DIVE project

    (Bologna : INGV, Istituto nazionale di geofisica e vulcanologia, Sezione di Bologna, 2010-, 2025-08-06) ; ; ; ;
    The ICDP DIVE project (Drilling the Ivrea‑Verbano zonE) addresses fundamental questions about the nature of the lower continental crust and its transition to the mantle. In its first phase, the project has drilled two, scientific, fully cored boreholes in the Ivrea Verbano Zone (IVZ) in Italy. The IVZ, considered the world’s best outcrop of lower crustal continental rocks, is structurally and historically connected to the underlying Ivrea Geophysical Body, a major, high density and high seismic‑velocity anomaly studied since the 1960s and a characteristic feature of the Western Alps. The two boreholes were conducted between 2022‑2024 in Val D’Ossola: the first in Ornavasso and the second in Megolo, 7 km apart. Within this framework, a dedicated seismographic network, named DIVEnet, has been monitoring natural earthquakes and possible operation‑related seismic activity for three years. Eleven seismographic stations (short period and broadband), provided by INGV and the University of Lausanne, were installed within a maximum distance of 15 km from the midpoint between the two drilling sites. All stations recorded data continuously and 10 provided data in real time. One broadband sensor was installed in a borehole, and its horizontal components’ orientation was determined by multiple methods. The stations occupied 14 different locations and operated from autumn 2021 to summer 2024, with varying recording durations. Being in an area characterized by low natural local seismicity and a relatively sparse distribution of seismographic stations, it is particularly important to record background activity and noise for as long as possible, especially before and after the start of drilling activities. Daily monitoring was conducted at INGV in quasi real time, and probabilistic power spectral density distributions (PPSD) have been computed. In total, 28 events with magnitudes ranging from 0 to 2.6 MLv were recorded within a distance of about 20 km from the boreholes, most of them aligned with the Insubric Line, that is thought to be tectonically inactive, and 612 events were recorded in the larger study region. No events were related to the drilling activities, which have only very slightly increased noise levels, mostly in the 0.1‑0.3 Hz frequency range.
      10  16
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    A strainmeter array as the fulcrum of novel observatory sites along the Alto Tiberina Near Fault Observatory

    (2024-06-24) ;
    Bennett, Richard
    ;
    Mencin, David
    ;
    Johnson, Wade
    ;
    Fault slip is a complex natural phenomenon involving multiple spatiotemporal scales from seconds to days to weeks. To understand the physical and chemical processes responsible for the full fault slip spectrum, a multidisciplinary approach is highly recommended. The Near Fault Observatories (NFOs) aim at providing highprecision and spatiotemporally dense multidisciplinary near-fault data, enabling the generation of new original observations and innovative scientific products. The Alto Tiberina Near Fault Observatory is a permanent monitoring infrastructure established around the Alto Tiberina fault (ATF), a 60 km long low-angle normal fault (mean dip 20°), located along a sector of the Northern Apennines (central Italy) undergoing an extension at a rate of about 3 mm yr −1. The presence of repeating earthquakes on the ATF and a steep gradient in crustal velocities measured across the ATF by GNSS stations suggest large and deep (5-12 km) portions of the ATF undergoing aseismic creep. Both laboratory and theoretical studies indicate that any given patch of a fault can creep, nucleate slow earthquakes, and host large earthquakes, as also documented in nature for certain ruptures (e.g., Iquique in 2014, Tōhoku in 2011, and Parkfield in 2004). Nonetheless, how a fault patch switches from one mode of slip to another, as well as the interaction between creep, slow slip, and regular earthquakes, is still poorly documented by near-field observation. With the strainmeter array along the Alto Tiberina fault system (STAR) project, we build a series of six geophysical observatory sites consisting of 80-160 m deep vertical boreholes instrumented with strainmeters and seismometers as well as meteorological and GNSS antennas and additional seismometers at the surface. By covering the portions of the ATF that exhibits repeated earthquakes at shallow depth (above 4 km) with these new observatory sites, we aim to collect unique open-access data to answer fundamental questions about the relationship between creep, slow slip, dynamic earthquake rupture, and tectonic faulting.
      13  79
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Esercitazione nazionale “Exe Sisma dello Stretto 2022” 04-06 novembre 2022. Rapporto di sintesi del Gruppo Operativo SISMIKO.

    Da venerdì 4 novembre a domenica 6 novembre 2022, si è tenuta una esercitazione nazionale denominata “Exe Sisma dello Stretto 2022” in un'area del territorio della Regione Calabria e della Regione Sicilia caratterizzata da una elevatissima pericolosità sismica. L’esercitazione è stata indetta e coordinata dal Dipartimento della Protezione Civile e aveva l’obiettivo di verificare la risposta operativa a un evento sismico significativo del Servizio Nazionale della Protezione Civile, di cui anche l’Istituto Nazionale di Geofisica e Vulcanologia fa parte. Durante le tre giornate, l’INGV ha avuto modo di testare tutte le procedure che l’Istituto ha codificato a partire da quelle del “Protocollo di Ente per le emergenze sismiche e da maremoto”. Dopo che INGV ha dato l’avvio all’intera esercitazione simulando il terremoto di magnitudo MW 6.2 (ML 6.0) alle ore 09:00 UTC in provincia di Reggio Calabria (5 km a SW dal comune di Laganadi), e ha, quindi, inviato il messaggio per il potenziale maremoto con un livello di allerta arancione; inoltre, il Presidente INGV ha prontamente convocato l’Unità di Crisi e attivato tutti Gruppi Operativi. Questi ultimi, nell’ambito dello scenario esercitativo, hanno verificato che i flussi di comunicazione interna e tutte le attività necessarie in emergenza sismica, presenti nei relativi protocolli operativi, risultassero rispettati. L’obiettivo primario dell’esercitazione è stato quindi quello di validare le attività previste e di aggiornare il personale afferente ai Gruppi Operativi stessi. Tra di essi, SISMIKO, che rappresenta il GO dedicato al coordinamento delle reti sismiche mobili INGV in emergenza, nelle settimane precedenti l’esercitazione ha predisposto tutte le attività che intendeva testare, descrivendole brevemente nel Documento d’impianto INGV e con maggior dettaglio in quello del Gruppo Operativo. A pochi giorni dalla chiusura dell’esercitazione, un terremoto di magnitudo ML 5.7 (MW 5.5) registrato alle ore 06:07 UTC del 09 novembre 2022 ha spostato l’attenzione dalla simulazione alla realtà.
      452  262
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Rapporto di sintesi del Gruppo Operativo SISMIKO a seguito del terremoto al largo della costa marchigiana settentrionale (Italia). MW 5.5 del 09-11-2022 ore 06:07 UTC

    Il 09 novembre 2022 alle ore 06:07 UTC (07:07 ora italiana) un terremoto di magnitudo ML 5.7 (MW 5.5) è stato localizzato dal sistema di sorveglianza sismica dell’Istituto Nazionale di Geofisica e Vulcanologia (INGV). L'epicentro è stato localizzato nel Mar Adriatico ad una distanza di circa 30 km dalla costa marchigiana in provincia di Pesaro e Urbino, a circa 31 km dalla città di Fano e 35 km dal capoluogo di provincia Pesaro. Il mainshock è stato seguito da una replica di ML 5.2 a un minuto di distanza. I due terremoti sono stati ben avvertiti in tutta la regione Marche, e anche in tutto il centro Italia fino a Roma e nelle regioni del nord Italia. Il Presidente dell’INGV, come previsto nel Protocollo di Ente per le emergenze sismiche e da maremoto, ha prontamente convocato l’Unità di Crisi e attivato tutti i Gruppi Operativi. Tra questi SISMIKO, che coordina le reti sismiche mobili INGV in emergenza, si è attivato immediatamente preparando la strumentazione necessaria per l’installazione di una rete sismica temporanea e per l’integrazione dei dati in acquisizione nel sistema di monitoraggio e sorveglianza sismica dell’INGV. Parallelamente alle attività di coordinamento e gestione dell’emergenza sono state attivate tutte le procedure inerenti la divulgazione (report, siti web, ecc) e l’analisi dei dati preliminari. La rete temporanea in emergenza è stata installata nelle prime 24 ore dalla scossa principale ad integrazione della rete sismica permanente dell’INGV in area epicentrale. La rete temporanea di SISMIKO, costituita da 8 stazioni sismiche trasmesse in tempo reale, ha permesso di migliorare il monitoraggio dell’evoluzione della sequenza, abbassando la soglia di detezione degli eventi sismici in area epicentrale e consentendo quindi una migliore localizzazione da parte del servizio di sorveglianza sismica nazionale. La gestione dell’emergenza sismica è avvenuta a pochi giorni di distanza dall’ esercitazione nazionale denominata “EXE Sisma dello Stretto 2022” svoltasi dal 4 al 6 Novembre 2022 nel territorio della Regione Calabria e della Regione Sicilia. L’esercitazione è stata coordinata dal Dipartimento della Protezione Civile. Le attività svolte durante EXE 2022 sono state per l’istituto, e in particolare per SISMIKO, propedeutiche per il buon esito di tutte le azioni messe in campo dall’INGV sin dai primi minuti dall’accadimento del mainshock del 9 Novembre.
      240  167
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Surface Velocities and Strain-Rates in the Euro-Mediterranean Region From Massive GPS Data Processing

    In this work we present and discuss new geodetic velocity and strain-rate fields for the Euro-Mediterranean region obtained from the analysis of continuous GNSS stations. We describe the procedures and methods adopted to analyze raw GPS observations from >4000 stations operating in the Euro-Mediterranean, Eurasian and African regions. The goal of this massive analysis is the monitoring of Earth’s crust deformation in response to tectonic processes, including plate- and micro-plate kinematics, geodynamics, active tectonics, earthquake-cycle, but also the study of a wide range of geophysical processes, natural and anthropogenic subsidence, sea-level changes, and hydrology. We describe the computational infrastructure, the methods and procedures adopted to obtain a threedimensional GPS velocity field, which is used to obtain spatial velocity gradients and horizontal strain-rates. We then focus on the Euro-Mediterranean region, where we discuss the horizontal and vertical velocities, and spatial velocity gradients, obtained from stations that have time-series lengths longer than 6 and 7 years, which are found to be the minimum spans to provide stable and reliable velocity estimates in the horizontal and vertical components, respectively. We compute the horizontal strain-rate field and discuss deformation patterns and kinematics along the major seismogenic belts of the Nubia-Eurasia plate boundary zone in the Mediterranean region. The distribution and density of continuous GNSS stations in our geodetic solution allow us to estimate the strain-rate field at a spatial scale of ~27 km over a large part of southern Europe, with the exclusion of the Dinaric mountains and Balkans.
      495  473
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    The INGV Mediterranean GNSS Archive (MGA)

    The Global Navigation Satellite System (GNSS) represents a primary data source in Solid Earth Sciences. In order to investigate the Earth’s crustal deformation, time series of the estimated daily positions of the stations are routinely analyzed at the Istituto Nazionale di Geofisica e Vulcanologia (INGV) to investigate the deformation of the Earth’s surface caused by tectonic and non-tectonic processes. The GNSS observations of the stations are processed using the three main scientific software: GAMIT/GLOBK, BERNESE, and GIPSY OASIS II. The accuracy and the strength of geodetic solutions often depend on the geometry and spatial density of the network, and the availability and quality of GNSS data. In many circumstances, GNSS networks are deployed for topographic purposes by private or public institutions, and a significant number of GNSS stations in large regions acquire continuous observations. It may happen that such networks do not collect and distribute data according to IGS standards, so it could be difficult to analyze this data using automated data-processing tools. For that reason, this data is often ignored or partially used by the scientific community, despite their potential usefulness in geodynamic studies. We have attempted troubleshooting this problem by establishing a centralized storage facility in order to collect all available GNSS data and standardize both formats and metadata information. Here we describe the processes and functions that manage this unified repository, called MGA (Mediterranean GNSS Archive), which regularly collects GNSS RINEX files from alarge number of CORS (Continuously Operating Reference Station) located across a wide region of mainly the European and African plates. RINEX observation data and metadata information are provided to the analysts through an FTP server and dedicated web-services. The complete data set is stored in a PostgreSQL database in order to easily retrieve pieces of information and efficiently manage the archive content. The system implements many high-level services that include scripts to download files from remote archives and to detect new available data, web applications such as API (Application Program Interface) to interact with the system, and background services that interact with the database. During the development of this product, particular attention was paid to what has already been achieved by EPOS TCS WP10, whose objective was: "[...] to develop an open source platform with programmatic and web interfaces to store and disseminate raw data and metadata from GNSS stations operating in Europe''. Many ideas and tools presented here were inspired by that project.
      334  324
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    PyGLogDB: software to generate STATION-INFO files for GNSS data analysis

    Massive analysis of GNSS data (Global Navigation Satellite System) requires the development of specific tools to automate the different steps of processing: from data download to ground displacements estimates. In this technical report we describe the tools and algorithms we have developed to handle the metadata associated with GNSS observations from continuous networks operating in the EuroMediterranean and African area, which are routinely processed by the three main INGV data analysis centers. Obtaining accurate metadata, which records information on how a GNSS station is equipped (receiver, antenna, monument, etc..), is mandatory in order to obtain accurate GNSS stations daily position and their evolution through time. Here we will describe the processing chain, the software developed using opensource programming language, describing the major issues found in treating incomplete, inconsistent or wrong information, and the methods adopted to minimize or resolve these problems. The software developed is going to be implemented in the centralized GNSS data and metadata archive that we are realizing at INGV, and that will serve both institutional activities and research projects. The goal of this tool is to minimize errors and reduce/avoid the human intervention in handling a large set of information, facilitating the automatic analysis of data from thousands of GNSS stations on a daily basis. The software acronym is pyGLogDB, which stands for: “python GNSS Logfile elaboration with the support of DataBase”.
      22  87
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Normal modes of a medieval tower excited by ambient vibrations in an urban environment

    We report on a passive seismic experiment on a historical tower in northern Italy. Assessment of dynamical properties of such structures is known to be very important to anticipate their response to possible earthquake excitation. We show how classical seismological analyses can image, in high definition and detail, many modes of vibration, continuously excited by background tremor due to vehicle traffic. Similarly to what Earth’s normal modes reveal, such information pose constraints on the elastic (and anelastic) structure of a building that, in the case of a historical edifice, are not generally known, because appropriate information on its fabrication and constitution is not available. Our case refers to the twelfth century, 97 m tall, Asinelli tower in Bologna (northern Italy)—the tallest slender masonry building in Europe. We detect and analyze several modes of free flexural vibration, besides compressional and torsional modes. Free vibrations occur with slightly different natural frequencies along two orthogonal directions, as a consequence of a discrepancy between centers of mass and stiffness. This is apparent by the splitting of frequencies of modes of vibration. For each mode, the polarization of particle motion shows that energy cyclically transfers between the two different degrees of freedom of the system. The spectral signature of the nearby Garisenda tower can also be recognized on the spectrum of Asinelli, and vice versa, but the frequencies differ, so there is no cross influence between the two. These data can be used to calibrate the parameters used for dynamic modeling, to investigate variations in time of the dynamic response, and to characterize the anthropogenic sources of ground motion to possibly mitigate their effects. Although the engineering community has extensively addressed the field of structural health monitoring with specific tools, we show that methods part of any seismologist toolbox can also provide detailed information about buildings that can be used for their numerical modeling.
      219  218
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Shear wave splitting in the Alpine region

    To constrain seismic anisotropy under and around the Alps in Europe, we study SKS shear wave splitting from the region densely covered by the AlpArray seismic network. We apply a technique based on measuring the splitting intensity, constraining well both the fast orientation and the splitting delay. Four years of teleseismic earthquake data were processed, from 723 temporary and permanent broad-band stations of the AlpArray deployment including ocean-bottom seismometers, providing a spatial coverage that is unprecedented. The technique is applied automatically (without human intervention), and it thus provides a reproducible image of anisotropic structure in and around the Alpine region. As in earlier studies, we observe a coherent rotation of fast axes in the western part of the Alpine chain, and a region of homogeneous fast orientation in the Central Alps. The spatial variation of splitting delay times is particularly interesting though. On one hand, there is a clear positive correlation with Alpine topography, suggesting that part of the seismic anisotropy (deformation) is caused by the Alpine orogeny. On the other hand, anisotropic strength around the mountain chain shows a distinct contrast between the Western and Eastern Alps. This difference is best explained by the more active mantle flow around the Western Alps. The new observational constraints, especially the splitting delay, provide new information on Alpine geodynamics. © 2021 The Author(s) 2021. Published by Oxford University Press on behalf of The Royal Astronomical Society.
      1638  209