Briole, Pierre
Preferred name
Briole, Pierre
Main Affiliation
36 results
Filters
Settings
The search returned 36 results
Now showing 1 - 10 of 36
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , The impact of Mount Etna sulfur emissions on the atmospheric composition and aerosol properties in the central Mediterranean: A statistical analysis over the period 2000–2013 based on observations and Lagrangian modelling
The emission of gases and aerosols due to volcanic activity may impact significantly atmospheric composition, cloud occurrence and properties, and the regional and global climate. While the effects of strong explosive (stratospheric) eruptions are relatively well known, limited information on the impacts of small to moderate volcanic activities, including passive degassing, is available. In this paper, the downwind impact of Mount Etna's sulfur emissions on the central Mediterranean is investigated on a statistical basis over the period 2000e2013 using: (a) daily sulfur dioxide emission rates measured near crater at Mount Etna with ground-based ultraviolet spectrophotometers, (b) Lagrangian trajectories and simulated plume dispersion obtained with the FLEXPART (FLEXible PARTicle dispersion) model, and (c) long-term observations of column SO2 concentration and aerosol Ångstr€om exponent a at Lampedusa (35.5 N, 12.6 E). This statistical analysis has allowed, for the first time, the characterization of decadal impact of Mount Etna's sulfur emissions on the sulfur dioxide and the aerosol microphysical/optical properties in the central Mediterranean. On average, statistically significant higher SO2 concentrations and smaller aerosol sizes are present when air masses from Mount Etna overpass Lampedusa. Despite being upwind of Lampedusa for only 5% of the time, Mount Etna is potentially responsible for up to 40% and 20% of the SO2 and a extreme values (exceedances of a fixed threshold), respectively, at this location. The most important factor determining this perturbation is the prevailing dynamics, while the magnitude of the SO2 emission rates from Mount Etna appears to be likely important only for relatively strong emissions. The observed perturbations to the aerosol size distribution are expected to produce a direct regional radiative effect in this area.186 7 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Ground Deformation and Seismic Fault Model of the M6.4 Durres (Albania) Nov. 26, 2019 Earthquake, based on GNSS/INSAR Observations
We identify the source of the Mw = 6.4 earthquake that rocked north-central Albania on November 26, 2019 02:54 UTC. We use synthetic aperture radar interferograms tied to the time series of coordinates of two permanent Global Navigation Satellite System (GNSS) stations (DUR2 and TIR2). We model the source by inverting the displacement data. Assuming in our model a half-space elastic medium and uniform slip along a rectangular fault surface, we invert the 104 picked measurements on a couple of ascending and descending interferograms to calculate the parameters of the fault. All inversions made with di erent input parameters converge towards a stable and robust solution with root mean square (r.m.s.) residual of 5.4 mm, thus ~1/5 of a fringe. They reveal that the earthquake occurred deep in the crust on a low-angle fault (23 ) dipping towards east with a centroid at 16.5 km depth. The best-fitting length and width of the fault are 22 and 13 km, and the reverse slip, 0.55 m. The seismic moment deduced from our model agrees with those of the published seismic moment tensors. This geometry is compatible with a blind thrust fault that may root on the main basal thrust, i.e., along the thrust front that separates Adria–Apulia from Eurasia. It is notable that there is a 123 ns yr-1 active shortening of the crust between the GNSS stations DUR2-TIR2 (equivalent to a shortening rate of 3.6 mm yr-1), and roughly in the east–west direction. Given this amount of strain the recurrence time of M6+ earthquakes along this fault should be of the order of 150 years.188 122 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Modeling of the 1980 Irpinia earthquake source : constrains from geodetic data
(1993); ; ; ;Pingue, F.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione OV, Napoli, ItaliaDe Natale, G.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione OV, Napoli, Italia159 249 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , The EtnaPlumeLab (EPL) research cluster: advance the understanding of Mt. Etna plume, from source characterisation to downwind impact
In 2013, a multidisciplinary research cluster named EtnaPlumeLab (EPL) was established, gathering experts from volcanology and atmospheric science communities. Target of EPL is to advance the understanding of Mt. Etna’s gas and aerosol emissions and the related processes, from source to its regional climatic impact in the Mediterranean area. Here, we present the cluster and its three interacting modules: EPL-RADIO (Radioactive Aerosols and other source parameters for better atmospheric Dispersion and Impact estimatiOns), SMED (Sulfur MEditerranean Dispersion) and Med-SuV (MEDiterranean SUpersite Volcanoes) Work Package 5. First results have provided pioneering highlights on the relevance of Mt. Etna’s plume impact at the Mediterranean regional scale. These results underline that further efforts need to be made to get insight into a synoptic volcanogenic-atmospheric chemistry/climatic understanding of volcanic plumes impact.192 61 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , A novel methodology to determine volcanic aerosols optical properties in the UV and NIR and Ångström parameters using Sun photometry
Remote volcanic aerosol optical depth (AOD) observations of Mount Etna summit and distal bulk plume have been carried out between 14 and 20 July 2016 in the framework of the EPL-RADIO project. Ultraviolet (UV) and near-infrared (NIR) AODs were measured using a Microtops-II Ozone Monitor (MIIOM) Sun photometer, using a Langley plot (LP) instrumental calibration routine. Ozone-corrected UV AODs at 320 nm are derived for the first time with a Microtops, thus extending the exploitable spectral band range of portable photometers to shorter wavelengths. The new UV AODs have theoretical uncertainties <±0.035 (±12%), dominated by LP calibration errors. Using UV and NIR AODs, the Ångström coefficients have been derived. The UV AODs and Ångström exponents have been compared, at background conditions, to colocated Cimel Sun photometer observations. A root-mean-square deviation of 0.03 (13%) for the UV AOD is found for this comparison, thus in agreement with estimated theoretical uncertainties. The MIIOM Ångström exponent estimations are found consistent with Cimel observations, even if with an average overestimation of 17.5%, mainly due to negative biases (−0.02/−21%) of NIR AODs. Results of quasi-simultaneous characterization of proximal and distal plume (7 km from craters), for 20 July 2016, are shown. During the measurements, brownish ash puffs were visible. While proximal and distal plumes were observed within approximately 1 h, their Ångström exponent varied significantly (mean values: −0.30±0.22 and 1.16±0.33, for the proximal and distal plumes). These results indicate quick sedimentation of ash particles and show the potential of this new retrieval technique to characterize volcanic aerosols.400 69 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , ROBOVOLC: a robot for volcano exploration result of rst test campaign
(2003); ; ; ; ROBOVOLC is a new robotic system that has been designed to help scientists in the exploration of volcanoes. It is composed of three subsystems: a rover platform with six articulated and independently actuated wheels; a manipulator arm to collect rock samples, drop and pick up sensors and sample gas; and a pan‐tilt turret with a high resolution camera, video‐camera, infrared camera and a doppler radar for gas speed measurement. This paper contains a short description of the system, following an introduction to the problem and review of the state‐of‐the‐art. Finally, results from the first test campaign on Mount Etna during September 2002 are briefly described.318 77 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Near-source high-rate GPS, strong motion and InSAR observations to image the 2015 Lefkada (Greece) Earthquake rupture history
The 2015/11/17 Lefkada (Greece) earthquake ruptured a segment of the Cephalonia Transform Fault (CTF) where probably the penultimate major event was in 1948. Using near-source strong motion and high sampling rate GPS data and Sentinel-1A SAR images on two tracks, we performed the inversion for the geometry, slip distribution and rupture history of the causative fault with a three-step self-consistent procedure, in which every step provided input parameters for the next one. Our preferred model results in a ~70° ESE-dipping and ~13° N-striking fault plane, with a strike-slip mechanism (rake ~169°) in agreement with the CTF tectonic regime. This model shows a bilateral propagation spanning ~9 s with the activation of three main slip patches, characterized by rise time and peak slip velocity in the ranges 2.5-3.5 s and 1.4-2.4 m/s, respectively, corresponding to 1.2-1.8 m of slip which is mainly concentrated in the shallower (<10 km) southern half of the causative fault. The inferred slip distribution and the resulting seismic moment (M0 = 1.05 × 1019N m) suggest a magnitude of Mw6.6. Our best solution suggests that the occurrence of large (Mw > 6) earthquakes to the northern and to the southern boundaries of the 2015 causative fault cannot be excluded.531 5 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , GPS network monitor the Western Alps deformation over a five year period: 1993-1998
(2002); ; ; ; GPS surveys in the Western Alps, performed in the time span 1993-2003, estimated the current crustal deformation of this area.184 27 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , The April 3, 2010 earthquake along the Pernicana fault (Mt. Etna - Italy): analysis of satellite and in situ ground deformation data integrated by the SISTEM approach
(2011-04); ; ; ; Etna is worldwide known as one of the most studied and monitored active volcanoes. Flank instability along the eastern and southern portion of Mt. Etna has been observed and measured thanks to geodetic networks and InSAR data analysis. The spreading area is bordered to the north by the east-west Pernicana Fault System (PFS) which dynamic is often linked with the eruptive activity, as recently observed during the 2002-2003 eruption. A seismic sequence occurred since April 2-3, 2010, along the PFS with two very shallow (a few hundred meters) mainshocks of magnitude 3.6 and 3.5. Explosions and ash emissions at the summit craters followed this swarm and culminated some days later (April 7-8). Just after the earthquake, specific GPS surveys were carried out aimed at monitoring the eastern part of the Pernicana fault, and the leveling route on the northeastern flank of the volcano was also surveyed. Trying to investigate the deformation occurred along the PFS during the events of April 3rd 2010, we performed a DInSAR (Differential Interferometric Synthetic Aperture Radar) analysis of ascending and descending Envisat, and of ascending ALOS-PALSAR images encompassing the date of the earthquake. The Envisat interferograms show very intense but local deformation on the Envisat ascending data and a low signal for the descending geometry, close to the Pernicana fault trace. This is probably due to the oblique normal/leftlateral kinematics of the PFS (as deduced also by GPS and leveling data), indeed both vertical (lowering) and horizontal (eastwards) components of motion produce a strong stretching of the LOS (Line Of Sight) distance for ascending geometry, while the two components act in opposite ways for the descending geometry, resulting in lower LOS distance variations compared to the ascending data set. We analyzed also the ALOS pair referring to 21/02/2010 – 08/04/2010 time and acquired along the ascending track number 638. The ALOS interferogram clearly show three fringes corresponding to roughly 35 cm of LOS displacement. The preliminary modeling of the interferograms agree with the seismic information (very shallow faulting, seismic moment) and show that the medium behave elastically. In order to investigate the ground deformation pattern associated with this event, an application of the novel SISTEM (Simultaneous and Integrated Strain Tensor Estimation from geodetic and satellite deformation Measurements) approach is presented here. To achieve higher accuracy and get better constraint of the 3D components of the displacements, we improved the standard formulation of SISTEM approach, based on the GPS and a single DInSAR sensor, in order to take into account all the available dataset (GPS, leveling, ascending and descending ENVISAT C-Band interferograms and the ALOS L-Band data). The 3D displacement maps obtained using the SISTEM approach well show the kinematics of the PFS, and are able to reconstruct also the ground deformation affecting the whole investigated area, defining the movements of the north-eastern flank of the volcano. These results, which provide an accurate spatial characterization of ground deformation, are hence promising for future studies aimed at improving the knowledge about the kinematics of the active faults of Mt. Etna.420 300 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Seismicity, deformation and seismic hazard in the western rift of Corinth: New insights from the Corinth Rift Laboratory (CRL)
(2006); ; ; ; This paper presents the main recent results obtained by the seismological and geophysical monitoring arrays in operation in the rift of Corinth, Greece. The Corinth Rift Laboratory (CRL) is set up near the western end of the rift, where instrumental seismicity and strain rate is highest. The seismicity is clustered between 5 and 10 km, defining an active layer, gently dipping north, on which the main normal faults, mostly dipping north, are rooting. It may be interpreted as a detachment zone, possibly related to the Phyllade thrust nappe. Young, active normal faults connecting the Aigion to the Psathopyrgos faults seem to control the spatial distribution of the microseismicity. This seismic activity is interpreted as a seismic creep from GPS measurements, which shows evidence for fast continuous slip on the deepest part on the detachment zone. Offshore, either the shallowest part of the faults is creeping, or the strain is relaxed in the shallow sediments, as inferred from the large NS strain gradient reported by GPS. The predicted subsidence of the central part of the rift is well fitted by the new continuous GPS measurements. The location of shallow earthquakes (between 5 and 3.5 km in depth) recorded on the on-shore Helike and Aigion faults are compatible with 50° and 60° mean dip angles, respectively. The offshore faults also show indirect evidence for high dip angles. This strongly differs from the low dip values reported for active faults more to the east of the rift, suggesting a significant structural or rheological change, possibly related to the hypothetical presence of the Phyllade nappe. Large seismic swarms, lasting weeks to months, seem to activate recent synrift as well as pre-rift faults. Most of the faults of the investigated area are in their latest part of cycle, so that the probability of at least one moderate to large earthquake (M = 6 to 6.7) is very high within a few decades. Furthermore, the region west to Aigion is likely to be in an accelerated state of extension, possibly 2 to 3 times its mean interseismic value. High resolution strain measurement, with a borehole dilatometer and long base hydrostatic tiltmeters, started end of 2002. A transient strain has been recorded by the dilatometer, lasting one hour, coincident with a local magnitude 3.7 earthquake. It is most probably associated with a slow slip event of magnitude around 5 ± 0.5. The pore pressure data from the 1 km deep AIG10 borehole, crossing the Aigion fault at depth, shows a 1 MPa overpressure and a large sensitivity to crustal strain changes.67 1
