Skip to main content
The search returned 4 results
Now showing 1 - 4 of 4
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Comparative Study of CPTU and SDMT in Liquefaction-Prone Silty Sands with Ground Improvement

    Following the 2012 Emilia-Romagna seismic sequence, widespread liquefaction of silty sands was observed, providing the opportunity to enhance our knowledge of the influence of fines content on seismic hazard and mitigation works. This paper presents the results of a thorough geotechnical investigation performed in connection with full-scale controlled blast tests in Bondeno, Italy, a small village that suffered liquefaction in 2012. Piezocone (CPTU) and seismic dilatometer (SDMT) tests were performed in natural and improved soils after rammed aggregate pier (RAP) treatment to a depth of 9.5 m to provide accurate soil characterization, evaluate liquefaction, and verify the effectiveness of the ground improvement. The combined use of piezocone (CPTU) and flat dilatometer (DMT) data provided reliable estimates of the overconsolidation ratio and at-rest earth pressure coefficient and highlighted the soil improvement in silty sands between 4 and 9 m in depth. Shear-wave velocity measurements showed a low sensitivity to RAP installation. The treatment effectiveness was also confirmed by the use of the simplified procedures for liquefaction assessment, underlining the important influence of the adopted fines profile and by the blast-induced liquefaction. CPTU and DMT parameters remained approximately unchanged between the piers after the detonation.
      140  169
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Liquefaction Mitigation of Silty Sands Using Rammed Aggregate Piers Based on Blast-Induced Liquefaction Testing

    To investigate the liquefaction mitigation capability of rammed aggregate piers (RAP) in silty sand, blast liquefaction testing was performed at a soil profile treated with a full-scale RAP group relative to an untreated soil profile. The RAP group consisted of 16 piers in a 4 × 4 arrangement at 2 m center-to-center spacing extending to a depth of 9.5 m. Blasting around the untreated area induced liquefaction (ru ≈ 1.0) from a 3 to 11 m depth, producing several large sand boils and causing a settlement of 10 cm. In contrast, the installation of the RAP group reduced excess pore water pressure (ru ≈ 0.75), eliminated sand ejecta, and reduced the average settlement to between 2 and 5 cm when subjected to the same blast charges. Although the liquefaction-induced settlement in the untreated area could be accurately estimated using an integrated cone penetration test (CPT)-based settlement approach, settlement in theRAPtreated area was significantly overestimated with the same approach, even after considering RAP treatment-induced densification. Analyses indicate that settlement after RAP treatment could be successfully estimated from liquefaction-induced compression of the sand and RAP acting as a composite material. This test program identifies a mechanism that explains how the settlement was reduced for the RAP group despite the elevated ru values in the silty sands that are often difficult to improve with vibratory methods.
      44  1
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Blast-induced liquefaction in silty sands for full-scale testing of ground improvement methods: Insights from a multidisciplinary study

    In the engineering geology field increased attention has been posed in recent years to potential liquefaction mitigation interventions in susceptible sand formations. In silty sands this is a major challenge because, as the fines content increases, vibratory methods for densification become progressively less effective. An alternative mitigation technique can be the installation of Rammed Aggregate Pier® (RAP) columns that can increase the resistance of the soil, accounting for its lateral stress increase and for the stiffness increase from soil and RAP composite response. To investigate the influence of these factors on liquefaction resistance, full-scale blast tests were performed at a silty sand site in Bondeno (Ferrara, Italy) where liquefaction was observed after the 2012 Emilia-Romagna earthquake. A multidisciplinary team of forty researchers carried out devoted experimental activities aimed at better understanding the liquefaction process at the field scale and the effectiveness of the treatment using inter-related methods. Both natural and improved areas were investigated by in-situ tests and later subjected to controlled blasting. The blast tests were monitored with geotechnical and geophysical instrumentation, topographical surveying and geological analyses on the sand boils. Results showed the RAP effectiveness due to the improvement of soil properties within the liquefiable layer and a consequent reduction of the blast-induced liquefaction settlements, likely due to soil densification and increased lateral stress. The applied multidisciplinary approach adopted for the study allowed better understanding of the mechanism involved in the liquefaction mitigation intervention and provided a better overall evaluation of mitigation effectiveness
      2078  132
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Interpreting the deformation phenomena triggered by the 2012 Emilia seismic sequence on the Canale Diversivo di Burana banks

    L’ articolo descrive uno studio riguardante i fenomeni deformativi osservati dopo il sisma dell’Emilia del maggio 2012 lungo un tratto di argine del Canale Diversivo di Burana che ricade nell’abitato di Scortichino, frazione del comune di Bondeno (FE). In questa porzione del rilevato arginale sono state edificate oltre un centinaio di abitazioni ed alcune strutture di medio-piccole dimensioni adibite ad attività produttive o a deposito, molte delle quali sono risultate pesantemente danneggiate e dichiarate inagibili proprio a causa delle deformazioni e del sistema di fratture longitudinali presenti nel terreno in seguito al terremoto. Il contributo qui presentato si prefigge di analizzare la risposta sismica dell’argine durante la sequenza sismica del 2012, comprendere le cause dei dissesti nonché individuare le necessarie azioni di mitigazione e gli eventuali interventi di messa in sicurezza nei confronti di terremoti futuri. A questo scopo è stata condotta un’ampia campagna sperimentale di indagini in sito e in laboratorio, finalizzata alla ricostruzione di un accurato modello geotecnico per la valutazione delle condizioni di stabilità dell’argine in condizioni sismiche, portando in conto anche l’eventuale insorgenza di fenomeni di liquefazione nei terreni sabbiosi superficiali costituenti la fondazione del corpo arginale. L’ analisi illustrata è il risultato dell’attività di indagine svolta per più di un anno dal Gruppo di Lavoro Argini (GdLA), costituitosi nel luglio 2012 in seguito ad un accordo fra la Regione Emilia-Romagna e l’Associazione Geotecnica Italiana per la verifica delle condizioni di stabilità dei rilevati arginali nelle aree colpite dal terremoto.
      188  258