University Hannover
3 results
Filters
Settings
The search returned 3 results
Now showing 1 - 3 of 3
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Glass forming ability and crystallisation behaviour of sub-alkaline silicate melts
(2015); ; ; ; been experimentally quantified via cooling-induced solidification approach. GFA is measured by the critical cooling rate Rc, the rate at which a melt solidifies ≤2 area% of crystals. Cooling rates of 9000, 1800, 180, 60, 7 and 1 °C/h have been run between 1300 °C (super-liquidus region) and 800 °C (quenching temperature), at air fO2 and ambient P for six silicate melts with compositions ranging from basalt (B) to rhyolite (R) (i.e., B100, B80R20, B60R40, B40R60, B20R80 and R100) and water contents comprised between 53 (B100) and 384 (B20R80) ppm. The ranges of cooling rates and chemical compositions used in this study are the broadest ever investigated in the Earth sciences. The phase proportions (area%) were determined by image analysis on about 500 back-scattered electron images collected over different magnifications. Phases are glass, clinopyroxene (cpx), spinel (sp) and plagioclase (plg). Sp is ubiquitous with abundance of few area% and nucleates earlier than silicate crystals. Cpx solidifies in all runs except in R100 and its abundance follows asymmetric broad Gaussian-like trends (with tails towards low rates) as a function of cooling rate. Moving from B100 to B40R60 these trends conserve their shape but shift progressively to lower cooling rates and mineral abundances. Plg crystallises only at low cooling rates and in SiO2-poor compositions. Run-products with low amounts of crystals (≤5 area%) clearly show that cpx preferentially nucleates on surfaces of sp, whereas a significant crystallisation of cpx (N5 area%) is observed with decreasing cooling rate and with changing composition from B100 to B20R80. The crystallisation of silicate crystals is related to the chemical diffusivity of components in the melt. Also the initial crystallisation of plg occurs preferentially on cpx. In general, the amount of crystals decreases as the cooling rate increases; however, in some cases, the amount of crystals remains constant or even decreases for B80R20 with decreasing cooling rate. Rc values change over 5 orders of magnitude being b1, 7, 620, 3020, 8020 and 9000 °C/h for R100, B20R80, B40R60, B60R40 and B80R20 and B100, respectively. The variation of Rc can be modelled through NBO/T (nonbridging oxygen per tetrahedron) parameter by the following equation: Rc=a / {1+e−[(NBO/T − b)/c]},where a, b and c are fitting parameters equal to 9214, 0.297 and 0.040, respectively. Similarly to other glass-forming liquids (network, metallic and molecular systems), Rc for natural sub-alkaline silicate melts is inversely related to the reduced glass transition parameter Trg (Trg=Tg / Tm) and can be quantified with the equation Rc= a × Trg−b, where a and b are 1.19 × 10−4 and 28.7, respectively. These results may be used to retrieve the solidification conditions of aphyric, degassed and oxidised lavas; in addition, our data provide general constrains on the crystallisation kinetics of natural crystal-bearing silicate melts erupted on Earth (e.g. lavas with phenocrysts). The relationship between crystal content and cooling rate suggests that the solidification path induced by degassing can be also complex and nonlinear. The growth of crystalswith size up to 1 mm from a nearly anhydrous superheated silicate melt indicates that variable cooling conditions of lavas have to be accounted to discriminate amongminerals formed before, during and after eruptions.Moreover, our results can be used to design glass-ceramics from naturally available easy to find, low-cost starting materials.524 75 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Viscosity of high-K basalt from the 5th April 2003 Stromboli paroxysmal explosion
(2009); ; ; ; The 5th April 2003 paroxysmal event was the strongest explosion that has occurred at Stromboli in the last 50 years. This event lasted only few minutes and was characterised by two violent explosions, followed by gas and pyroclast emission. In order to constrain models of the dynamics of the paroxystic event the viscosity of anhydrous and hydrous Stromboli high potassium (HK)-basaltic melts have been measured. Viscosity has been investigated in the low viscosity range with the falling sphere method at superliquidus temperatures (1423 to 1673 K) and 0.5 GPa and in the high viscosity range with micropenetration near the glass transition temperature (723 to 1035 K) at atmospheric pressure. Falling sphere experiments were performed in a piston cylinder apparatus with melts whose water content varies from nominally anhydrous (0.02 wt.% H2O) to 4.16 wt.% H2O. The combination of high- and low-viscosity data permits a general description of the viscosity as a function of temperature and water contentusing a modified Tamman–Vogel–Fulcher equation. Using these new viscosity data, an estimation of the flow regime and magma velocity is performed. Our data suggest that the ascent of magma from the 7–8 km deep reservoir to a shallower reservoir located at about 3 km of depth, may occur within minutes. Moreover, we infer a turbulent flow regime. Finally, our estimates of the ascent velocity agree qualitatively with results from petrological studies (e.g. [Bertagnini, A., Métrich, N., Landi, P., Rosi, M., 2003. Stromboli volcano (Aeolian Archipelago, Italy): an openwindowon the deep-feeding system of a steady state basaltic volcano. Journal of Geophysical Research 108, 2336–2350.]), which indicate a turbulent flow regime and rapid ascent velocities such to inhibit volatile-loss-induced crystallization.We conclude that hazard evaluation at Stromboli Island should incorporate the likelihood of very rapid ascent of less-evolved melts from depth.334 30 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , A general viscosity model of Campi Flegrei (Italy) melts
(2011); ; ; ; Viscosities of shoshonitic and latitic melts, relevant to the Campi Flegrei caldera magmas, have been experimentally determined at atmospheric pressure and 0.5 GPa, temperatures between 840 K and 1870 K, and H2O contents from 0.02 to 3.30 wt%. The concentric cylinder technique was employed at atmospheric pressure to determine viscosity of nominally anhydrous melts in the viscosity range of 101.5 - 103 Pa·s. The micropenetration technique was used to determine the viscosity of hydrous and anhydrous melts at atmospheric pressure in the high viscosity range (1010 Pa·s). Falling sphere experiments were performed at 0.5 GPa in the low viscosity range (from 100.35 to 102.79 Pa·s) in order to obtain viscosity data of anhydrous and hydrous melts. The combination of data obtained from the three different techniques adopted permits a general description of viscosity as a function of temperature and water content using the following modified VFT equation: where η is the viscosity in Pa·s, T the temperature in K, w the H2O content in wt%, and a, b, c, d, e, g are the VFT parameters. This model reproduces the experimental data (95 measurements) with a 1σ standard deviation of 0.19 and 0.22 log units for shoshonite and latite, respectively. The proposed model has been applied also to a more evolved composition (trachyte) from the same area in order to create a general model applicable to the whole compositional range of Campi Flegrei products. Moreover, speed data have been used to constrain the ascent velocity of latitic, shoshonitic, and trachytic melts within dikes. Using petrological data and volcanological information (geometrical parameters of the eruptive fissure and depth of magma storage), we estimate a time scale for the ascent of melt from 9 km to 4 km depth (where deep and shallow reservoirs, respectively, are located) in the order of few minutes. Such a rapid ascent should be taken into account for the hazard assessment in the Campi Flegrei area.321 418
