Skip to main content
The search returned 117 results
Now showing 1 - 10 of 117
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Predominant frequency variations in the ambient noise recorded in the Colfiorito basin (Umbria, Italy)

    The Colfiorito basin is located at the boundary between Umbria and Marche districts in Central Italy. The area was struck by several strong earthquakes in the past, and during the September 1997 to April 1998 seismic sequence, the macroseismic intensity was as large as IX (MCS scale) in the region. Ambient noise measurements are carried out over fifty points in the basin; H/V spectral ratios as well as spectral ratios using a reference rock site are calculated. Polarization analyses are also performed in narrow frequency bands where spectral amplitude peaks are observed to dominate, to discriminate preferential directions of propagation in the noise wave field which could be related to source or path effects, other than site effects. In the spectral ratios, the frequencies of the most pronounced peaks generally agree with the resonance frequencies computed for the measurement sites on the basis of 1-D velocity models, at least where no strong lateral variations of the sediment thickness are present.
      152  336
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Results from shallow geophysical investigations in the northwestern sector of the island of Malta

    We performed geophysical investigations in the northwestern sector of the island of Malta to reconstruct velocity-depth models and provide shear-wave velocity profiles. We have chosen two sites, one located in Rabat (Malta) and another in the Golden Bay area. We used both active (seismic and electrical 2D-tomography, Multichanel Analysis of Surface Waves – MASW) and passive (2D arrays and single-station measurements using ambient noise) geophysical methods. Consistently with previous studies performed in this part of Malta, we have found that both sites are characterised by site resonance in the frequency range 1-2 Hz as an effect of the local lithostratigraphic succession that shows an impedance contrast at about 60-90 m depth. This resonance effect can have important implications on both seismic hazard as well as seismic risk evaluation of the region since the amplified frequency range coincides with the resonance frequencies typical of 5–10 storey buildings which are very diffuse in the Maltese Islands, especially after intense recent urbanization.
      1246  10
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Test sites in Europe for the evaluation of ground motion amplification: site response of the Gubbio basin (Central Italy) using weak motions recorded by linear seismic arrays

    The plain of Gubbio is located in a northwest-southeast oriented, 4-km wide, 20-km long intermountain basin in the northern Apennines, central Italy. The moderate-magnitude earthquakes of the 1997 Umbria-Marche seismic sequence, occurred 40 km southeast of Gubbio, generated displacements as large as 6 cm within the basin. The large amplitude phase, not observed outside of the basin, was followed by low-frequency wave trains lasting up to 1 minute. In order to investigate the mechanism of possible local amplification effects, different kind of geophysical and geological investigation of the basin started within the framework of the Italian DPC-INGV projects. In particular, the GFZ and the INGV deployed two linear seismic arrays. The first one was composed of ten seismological stations with 1-s receivers. It operated from June until December 2005. The array was oriented north-south, approximately: all the stations but two were installed on the sedimentary deposits. The remaining two stations (the northernmost and the southernmost) were installed on rock outcrops at the edges of the basin. The second array, composed by 10 stations with 5-s receivers, was deployed along the main axis of the basin, and is recording since November 2005. For 45 days, the two arrays worked simultaneously. A selected dataset of 250 earthquakes has been analyzed. H/V spectral ratio results show that systematic low-frequency (0.3-0.4 Hz) amplification affects the stations in the middle of the basin. The resonance frequency peaks are consistent with the thickness and the average S-wave velocity of soft sediments derived from microtremor measurements in the basin. The conventional spectral ratio results show a more complex broad-band (0.3-10 Hz) amplification. The analysis of selected records by means of a sonogram approach highlights the arrival of strong late phases increasing the signal duration at the stations located in the middle of the basin.
      142  310
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Estimates of ground motions in the Phlegraean Fields produced by potential seismogenic sources of major interest for the city of Naples, Italy

    This study is aimed at predicting the strong ground shaking in the Phlegraen Fields area, in the western part of the city of Naples, by the use of synthetic simulations of the seismic radiation possibly produced by earthquakes occurring on active faults of the southern Apennines range. Given their distance, geometry and expected mechanism these faults have been selected as the potentially most dangerous ones for the city of Naples. We selected the seismogenic sources associated with earthquakes having caused intensity equal or above VII in the city of Naples and having occurred in the past 700 years (the most reliable time window for the historical earthquake catalogue). All seismogenic sources were taken from INGV’s DISS database. These faults are long and relatively shallow structures (length greater than 25 km and maximum depth within 13 km) having seismic moment and focal mechanism comparable to the 1980, M 6.9 Irpinia earthquake. According to the literature, the latter is included in our simulation study by considering the occurrence of three separate rupture processes along three distinct fault segments. A suite of synthetic seismograms at the basement rock in Naples for each considered fault has been generated by using the discrete wavenumber method proposed by Bouchon (1981) numerically implemented for the computation of complete wave field Green’s function in a flat-layered medium. We adopted a simplified source model (line source Haskell model) to simulate the kinematic rupture process along an extended source, allowing for rupture nucleation in the middle (bi-lateral) and at the edge (uni-lateral) of the Haskell line. This approach has been preliminary tested and validated with the comparison between synthetic and observed 10-Hz low-pass filtered 1980 Irpinia earthquake records. The investigated site is located in the eastern part of the Phlegraen caldera, a plain area filled with recent (< 12,000 yr) pyroclastic soils. Several specific experiments were performed to evaluate the effect of surface geology on ground shaking. The experimental data used in this study come from a 2D active refraction seismic survey, from the spectral analysis of the shot-induced multichannel surface-waves (MASW), and from a 2D small-aperture array that recorded both natural earthquakes and ambient noise. Simultaneously, a firm-site reference station was also operating on an outcrop of yellow Neapolitan tuff (lithoid facies), about 1 km away from the array. These data, integrated with stratigraphy available from boreholes drilled in the plain, allowed us to reconstruct a 1D vertical profile of shear-wave velocities at the site of interest. This velocity model was mostly based on the inversion of the dispersion curves obtained from ambient noise measured at the array combined with MASW results from the refraction survey. The fundamental resonance frequency of the site was assessed around 1 Hz. At this frequency, the soft-to-firm spectral ratios computed from the recorded earthquakes are consistent with the theoretical transfer function of the model in terms of both predominant frequency and amplitude. The rock-site synthetic seismograms were then convolved by the site theoretical transfer function in a linear-equivalent approach, where shear-modulus and damping curves for the soft materials of the uppermost layers are taken from the literature. Acceleration and displacement response spectra were computed from the convolved synthetics. A comparison of the retrieved response spectra with those required by the Italian seismic code (Italian government ordinance PCM 3274 of 20 March 2003) suggests that our results are consistent with expectations at short-periods (T< 2 s) but some discrepancies arise at longer periods, where our predictions exceed the spectral ordinates of the seismic codes. This finding stresses the need for more thorough investigations of intermediate-period surface waves
      264  1173
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Directional resonance variations across the Pernicana Fault, Mt Etna, in relation to brittle deformation fields

    The Pernicana Fault (PF) is the main structural element of Mt Etna and the northern boundary of a section sliding to the southeast. Observed ground motion records in the damage zone of the PF show strong variations of directional resonance in the horizontal plane. The observed resonance directions exhibit an abrupt rotation of azimuth by about 30◦ across the fault, varying from N166◦ on the north side to N139◦ on the south. We interpret the directional resonance observations in terms of changes in the kinematics and deformation fields on the opposite sides of the fault. The northern side is affected primarily by the left-lateral strike-slip movement, whereas the southern side, that is subjected also to sliding, is under a dominant extensional stress regime. Brittle deformation models based on the observed kinematic field predict different sets of fractures on the opposite sides of the fault: synthetic cleavages and extensional fractures are expected to dominate in the northern and southern sides, respectively. These two fracture fields have different orientations (N74◦ and N42◦, respectively) and both show a near-orthogonal relation (∼88◦ in the northern sector and ∼83◦ to the south) with the azimuth of the observed directional resonance. We conclude that the direction of the largest resonance motions is sensitive to and has transversal relationship with the dominant fracture orientation. The directional amplification is inferred to be produced by stiffness anisotropy of the fault damage zone, with larger seismic motions normal to the fractures.
      335  29
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Difference in shaking intensity between short and tall buildings: known and new findings

    We investigate the influence of building height on the ability of people to feel earthquakes and observe that, in an urban area, short and tall buildings reach different levels of excitation. We quantify this behavior by analyzing macroseismic reports collected from individuals through the Internet, focusing on transitory effects, therefore in the elastic regime during recent earthquakes in Italy in the local magnitude (ML) range of 3 to 5.9. We find a maximum difference of 0.6 intensity units between the top floors of tall (7–10 stories) and short (1–2 stories) buildings at the highest considered magnitudes. As expected, tall buildings experience greater shaking than short buildings during large earthquakes at large source distances. However, we observe the opposite behavior at close distances when the ML is less than 3.5. These results can be explained by considering the different spectra radiated by small and large earthquakes and the different fundamental mode resonances of buildings (i.e., shorter buildings have higher resonance frequencies and vice versa). Using idealized building models excited by real acceleration time histories, we compute synthetic accelerograms on the top floors of short and tall buildings, and confirm the trend of the observed differences in felt intensities.
      453  265
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Stress drop, apparent stress, and radiation efficiency of clustered earthquakes in the nucleation volume of the April 6, 2009, M w 6.1 L’Aquila earthquake

    We investigate the variability of Brune stress drop (∆σ) and apparent stress (τ a ) of 23 earthquakes occurred in a small crustal volume adjacent to the hypocenter of the destructive M w 6.1 L’Aquila earthquake. Their magnitude range is 2.7 ≤ M w ≤ 4.1. Inter- event variability of stress drop and apparent stress results in a factor of ten, well beyond the individual-event uncertainty. Radiation efficiency η sw = τ a /∆σ varies mostly between 0.1 and 0.2 but, in the days immediately before and after the main shock, η sw tends to be smaller decreasing to values as low as 0.06. This may be the consequence of ruptures migrating in those days into a focal volume with higher dynamic strength. The temporal change of η sw is tentatively interpreted as a spatial variation due to the earthquake migration into the locked portion of the fault that originated the main shock. Consistently, no variation in stress drop and apparent stress is observed between foreshocks and aftershocks but the smallest and largest ∆σ result in a good correlation with the largest and smallest b-values, respectively, imaged by other authors in the rupture nucleation volume.
      144  186
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    GROUND MOTION POLARIZATION IN FAULT ZONES : RELATION WITH BRITTLE DEFORMATION FIELDS

    (2010-12-13) ; ; ; ;
    Pischiutta, Marta; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, Italia
    Several recent studies indicate that ambient noise and seismic signals in fault zones tend to be polarized on the horizontal plane with a clear preferred orientation direction. Here we present a summary of past experiments as well as new study cases showing evidence of this effect: the Val d’Agri, the Pernicana and the Paganica faults in Italy, and the Hayward fault in California. We also analyze data recorded by the HRSN network at the Parkfield section of the San Andreas fault and find that stations MM and GH that are close to the fault damage zone show a similar persistent and marked polarization effect. The approach combines the H/V technique in the frequency domain with the covariance matrix diagonalization method in the time domain. Common features are: i) a high stability of results at each site, independently of the nature and location of the source of seismic signals, ii) a characteristic polarization for each fault, and iii) the preferred polarization is close to the fault-normal direction, rather than being fault parallel as would be expected for generation of fault zone trapped waves. In previous papers, the role of fluid-filled microcracks in the damage zone was hypothesized. We have then explored an hypothesis based on the fracture field orientation in the fault damage zone by applying the package FRAP3 (Salvini, 2002) to model the brittle deformation field expected for the studied faults. We have found a consistent orthogonal relation between the observed polarizations and the orientation of the predicted synthetic fracture systems. When anisotropy studies are available, the horizontal ground motion polarization is consistently found to be perpendicular to the fast wave splitting component. The results may reflect reduced stiffness in the fault-normal direction produced by the presence of damage fault zone rocks.
      139  169
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    STRESS PARAMETERS OF REPEATING EARTHQUAKES IN THE NUCLEATION VOLUME OF THE APRIL 6, 2009, MW 6.1 L'AQUILA EARTHQUAKE

    We analyze the state of stress for 28 repeaters, foreshocks, mainshock and aftershocks, in the rupture nucleation volume of the destructive L’Aquila earthquake including the strongest Mw4.1 foreshock occurred one week before the mainshock. In a previous paper, earthquakes clustered in this crustal volume were used to detect a transient anomaly of shear wave velocity in the fault zone a ten of hours after the Mw 4.1 foreshock. The purpose of this study is to investigate whether stress parameters had concomitantly temporal or spatial variations. Brune stress drop was computed in a EGF-approach and apparent stress was derived from energy of seismograms. Estimates of individual stations and individual events showed large fluctuations, mostly due to rupture directivity and site effects. A procedure was adopted to decrease the estimate uncertainty obtaining a 39% of the total variance reduction. Brune stress drop and apparent stress showed similar trends implyingstable values of radiation efficiency around 0.23, which is the value expected for self- similarruptures. No evident temporal change emerges from the analyzed stress parameters of repeaters. In contrast, the spatial pattern of Brune stress drop shows a correlation with the b-value obtained by Sugan et al., 2014 that evidenced an asperity characterized by a low b-value on and around the nucleation zone of the mainshock.
      61  115
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    A study of building vibrations induced by weak motions: effects of earthquake excitation, ambient noise and wind speed

    We carried out a vibration study experiment on a masonry building in the town of Ariano Irpino, southern Italy, using six-channel stations equipped with three-component velocity-transducers and accelerometers and running in continuous modality from January 2006 to December 2007. The analysis of weak motions from several local earthquakes, together with the 3D numerical modelling of the structure, allowed us to identify the first three vibration modes of the target building. Therefore, we checked the validity of ambient noise data to determine the vibration frequencies of buildings. The analysis tools based on earthquake and ambient noise data were conventional, i.e. spectral ratios between homologous components of stations at high floors in the building with respect to a station installed at the basement, and single-station spectral ratios between horizontal and vertical components. The indications derived from earthquakes and ambient noise result in a satisfactory agreement for frequencies between 1 and 20 Hz when using recordings characterized by low levels of amplitude, both for cultural and meteorological noise. In contrast, when the wind speed increases (above 20 km/h, approximately) seismic noise shows an excess of horizontal vibrations at low frequencies (below 2 Hz). These extra-amplitudes are not related to the seismic input vertically incident to the basement, but are probably due to the lateral action of the wind on the building. In contrast anthropic activities do not affect considerably the trend of spectral ratios in the range of frequencies that include the first modes of vibration of the building, even at high noise level.
      588  133