Si, Jialiang
The search returned 4 results
Now showing 1 - 4 of 4
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Fault gouge graphitization as evidence of past seismic slip
One moderate- to large-magnitude earthquake (M > 6) nucleates in Earth’s crust every three days on average, but the geological record of ancient fault slip at meters-per-second seismic velocities (as opposed to subseismic slow-slip creep) remains debated because of the lack of established fault-zone evidence of seismic slip. Here we show that the irreversible temperature-dependent transformation of carbonaceous material (CM, a constituent of many fault gouges) into graphite is a reliable tracer of seismic fault slip. We sheared CM-bearing fault rocks in the laboratory at just above subseismic and at seismic velocities under both water-rich and water-deficient conditions and modeled the temperature evolution with slip. By means of micro-Raman spectroscopy and focused-ion beam transmission electron microscopy, we detected graphite grains similar to those found in the principal slip zone of the A.D. 2008 Wenchuan (Mw 7.9) earthquake (southeast Tibet) only in experiments conducted at seismic velocities. The experimental evidence presented here suggests that high-temperature pulses associated with seismic slip induce graphitization of CM. Importantly, the occurrence of graphitized fault-zone CM may allow us to ascertain the seismogenic potential of faults in areas worldwide with incomplete historical earthquake catalogues.418 86 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Melting of fault gouge at shallow depth during the 2008 MW 7.9 Wenchuan earthquake, China
(2023-02-09); ; ; ; Typical rocks at shallow depths of seismogenic faults are fluid-rich gouges. During earthquakes, on-fault frictional heating may trigger thermal pressurization and dynamic fault weakening. We show that frictional melting, rather than thermal pressurization, occurred at shallow depths during the 2008 MW 7.9 Wenchuan earthquake, China. One year after the Wenchuan earthquake, we found an ~2-mm-thick, glass-bearing pseudotachylyte (solidified frictional melt) in the fault gouges retrieved at 732.6 m depth from the first borehole of the Wenchuan Earthquake Fault Scientific Drilling Project. The matrix of pseudotachylyte is enriched in barium and cut by barite-bearing veins, which provide evidence of co- and postseismic fluid percolation. Because pseudotachylyte can be rapidly altered in the presence of percolating fluids, its preservation suggests that gouge melting occurred in a recent large earthquake, possibly the Wenchuan earthquake. Rock friction experiments on fluid-rich fault gouges deformed at conditions expected for seismic slip at borehole depths showed the generation of pseudotachylytes. This result, along with the presence of a second slip zone attributed to the Wenchuan earthquake at 589.2 m depth, implies that during large earthquakes, frictional melting can occur at shallow depths and that seismic slip can be accommodated by multiple faults. This conclusion is consistent with the evidence from surface faulting that multiple ruptures propagated during the Wenchuan earthquake.67 198 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Gouge graphitization and dynamic fault weakening during the 2008 Mw 7.9 Wenchuan earthquake
(2013-11); ; ; ; The Longmenshan fault that ruptured during the 2008 Mw 7.9 Wenchuan (China) earthquake was drilled to a depth of 1200 m, and fault rocks including those in the 2008 earthquake slip zone were recovered at a depth of 575–595 m. We report laboratory strength measurements and microstructural observations from samples of slip zone fault rocks at deformation conditions expected for coseismic slip at borehole depths. Results indicate that the Longmenshan fault at this locality is extremely weak at seismic slip rates. In situ synchrotron X-ray diffraction analysis indicates that graphite was formed along localized slip zones in the experimental products, similar to the occurrence of graphite in the natural principal slip zone of the 2008 Wenchuan rupture. We surmise that graphitization occurred due to frictional heating of carbonaceous minerals. Because graphitization was associated with strong dynamic weakening in the experiments, we further infer that the Longmenshan fault was extremely weak at borehole depths during the 2008 Wenchuan earthquake, and that enrichment of graphite along localized slip zones could be used as an indicator of transient frictional heating during seismic slip in the upper crust.191 29 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Frictional Properties of the Longmenshan Fault Belt Gouges From WFSD‐3 and Implications for Earthquake Rupture Propagation
(2022-05); ; ; ; The 2008 Mw 7.9 Wenchuan earthquake generated ∼270 and ∼80 km long surface ruptures along the Longmenshan fault belt, namely the Yingxiu-Beichuan fault (YBF) and the Guanxian-Anxian faults (GAF), respectively. So far, most of the frictional investigations were performed on the YBF gouge materials. Here, we present the results of rotary shear friction experiments performed on the GAF gouges recovered from the depth of ∼1.25 km of the Wenchuan Earthquake Fault Scientific Drilling project-3 along the GAF. The fault gouges, mainly composed of quartz, illite, chlorite, and kaolinite, were sheared at slip velocities V ranging from 10−5 to 2 m/s and normal stresses from 8.5 to 10 MPa under both room humidity and wet conditions. At any imposed slip velocity, the wet gouges have an apparent friction coefficient lower than the room humidity one. In addition, enhanced velocity-strengthening behavior at intermediate velocities (10 −2 m/s < V ≤ 10 −1 m/s) was recognized. We characterized the products using field-emission scanning electron microscopy combined with synchrotron X-ray diffraction analysis. These microanalytical investigations evidence the formation of size reduced particles (without mineral phase changes) and R- and Y-shears in the principal slip zone (PSZ). Regardless of the ambient conditions, the width of PSZ was proportional to the input frictional work density (the product of shear stress times displacement). Our results support the hypothesis that the GAF preferentially ruptures through wet fault gouges; however, the enhanced velocity-strengthening regime at intermediate velocities may act as a barrier to slip acceleration during fault rupture propagation.201 291
