Di Giulio, Giuseppe
Preferred name
Di Giulio, Giuseppe
Email
giuseppe.digiulio@ingv.it
Staff
staff
ORCID
Researcher ID
I-5598-2015
177 results
Filters
Settings
The search returned 177 results
Now showing 1 - 10 of 177
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Empirical evaluation of microtremor H/V spectral ratio
(2008-02-08); ; ; ; The objective of this work is to perform a purely empirical assessment of the actual capabilities of the horizontal-to-vertical (H/V) spectral ratio technique to provide reliable and relevant information concerning site conditions and/or site amplification. This objective has been tackled through the homogeneous (re)processing of a large volume of earthquakes and ambient noise data recorded by different research teams in more than 200 sites located mainly in Europe, but also in the Caribbean and in Tehran. The original recordings were first gathered in a specific database with information on both the sites and recorded events. Then, for all sites close to an instrumented reference, average site-to-reference spectral ratios (“spectral ratio method” (SSR)) were derived in a homogeneous way (window selection, smoothing, signal-to-noise ratio threshold, averaging), as well as H/V ratios (“HVSRE–RF”) on earthquake recordings. H/V ratios were also obtained from noise recordings at each site (either specific measurements, or extracted from pre- or post-event noise windows). The spectral curves resulting from these three techniques were estimated reliable for a subset of 104 sites, and were thus compared in terms of fundamental frequency, amplitude and amplification bandwidth, exhibiting agreements and disagreements, for which interpretations are looked for in relation with characteristics of site conditions. The first important result consists in the very good agreement between fundamental frequencies obtained with either technique, observed for 81% of the analyzed sites. A significant part of the disagreements correspond to thick, low frequency, continental sites where natural noise level is often very low and H/V noise ratios do not exhibit any clear peak. The second important result is the absence of correlation between H/V peak amplitude and the actual site amplification measured on site-to-reference spectral ratios. There are, however, two statistically significant results about the amplitude of the H/V curve: the peak amplitude may be considered as a lower bound estimate of the actual amplification indicated by SSR (it is smaller for 79% of the 104 investigated sites), and, from another point of view, the difference in amplitude exhibits a questioning correlation with the geometrical characteristics of the sediment/basement interface: large SSR/HV differences might thus help to detect the existence of significant 2D or 3D effects.271 31 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Predictions of kumamoto ground motion from linear and nonlinear 2d simulation in the framework of egs step 2 and step 3 blind test
We present the results of 2D numerical simulation carried out using FLAC3D-7.0. The model geometry has been derived by the seismic section provided by the ESGG6 organizing committee (CMPM) and by the Japan Integrated Velocity Structure Model (JIVSM). The seismic velocity model and density were derived from the 1D preferred model proposed by CMPM for the units filling the Kumamoto Plain, and from the JIVSM for the Mount Kinbo area. We have performed an elastic simulation for Step2, while for Step3, in addition to a linear elastic simulation, a non-linear elasto-plastic simulation has been run using the Mohr-Coulomb constitutive law to characterize some shallow layers. For Step3 linear and nonlinear synthetics waveforms are almost identical, likely due to the mechanical parameters and the constitutive model chosen being not able to induce non-linear effects. Synthetic results are presented for horizontal and vertical components of ground motion.47 105 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Exploring the model space and ranking a best class of models in surface- wave dispersion inversion: Application at European strong-motion sites
(2012-05-02); ; ; ; The inversion of surface-wave dispersion curve to derive shear-wave velocity profile is a very delicate process dealing with a non-unique problem, which is strongly dependent on the model space parameterization. When independent and reliable information are not available, the selection of most representative models within the ensemble produced by the inversion is often difficult. We present a strategy in the inversion of dispersion curves able to investigate the influence of the parameterization of the model space, and to select a ‘’best’’ class of models. We analyze surface-wave dispersion curves measured at 14 European strong-motion sites within the EC-project NERIES. We focus on the inversion task exploring the model space by means of four distinct parameterization classes composed of layers progressively added over a half-space. The classes differ in the definition of the shear-wave velocity profile; we consider models with uniform velocity as well as models with increasing velocity with depth. At each site and for each model parameterization, we perform an extensive surface-wave inversion (200100 models for 5 seeds) using the conditional neighbourhood algorithm. We address the model evaluation following the corrected Akaike’s Information Criterion (AICc) which combines the concept of misfit to the number of degrees of freedom (dof) of the system. The misfit is computed as least-squares estimation between theoretical and observed dispersion curve. The model complexity is accounted in a penalty term by AICc. By applying such inversion strategy on 14 strong-motion sites, we find that the best parameterization of the model space is mostly 3-4 layers over a half-space; where the shear-wave velocity of the uppermost layers can follow uniform or power-law dependence with depth. The shear-wave velocity profiles derived by inversion agree with shear-wave velocity profiles provided by borehole surveys at approximately 80% of the sites.166 38 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Seismic response of a deep continental basin including velocity inversion: the Sulmona intramontane basin (Central Apennines, Italy)
(2016-01-01); ; ; ; The Sulmona plain (central Italy) is an intramontane basin of the Abruzzi Apennines that is known in the literature for its high seismic hazard. We use extensive measurements of ambient noise to map the fundamental frequency and to detect the presence of geological heterogeneities in the basin. We perform noise measurements along two basin-scale orthogonal transects, in conjunction with 2-D array experiments in specific key areas. The key areas are located in different positions with respect to the basin margins: one at the eastern boundary (fault-controlled basin margin) and one in the deepest part of the basin. We also collect independent data by using active seismic experiments (MASW), down-hole and geological surveys to characterize the near-surface geology of the investigated sites. In detail, the H/V noise spectral ratios and 2-D array techniques indicate a fundamental resonance (f0) in the low-frequency range (0.35–0.4 Hz) in the Sulmona Basin. Additionally, our results highlight the important role that is played by the alluvial fans near the edge-sectors of the basin, which are responsible for a velocity inversion in the uppermost layering of the soil profile. The H/V ratios and the dispersion curves of adjacent measurements strongly vary over a few dozens of meters in the alluvial fan area. Furthermore, we perform 1-D numerical simulations that are based on a linear-equivalent approach to estimate the site response in the key areas, using realistic seismic inputs. Finally, we perform a 2-D simulation that is based on the spectral element method to propagate surface waves in a simple model with an uppermost stiff layer, which is responsible for the velocity inversion. The results from the 2-D modelling agree with the experimental curves, showing deamplified H/V curves and typical shapes of dispersion curves of a not normally dispersive site.291 80 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Ambient vibration analysis as a proxy for the detection of buried geological structures
In this work we tested the capability of single station ambient noise spectral ratios (HVNSR) technique to be used as a proxy for detecting sharp variations in the subsoil characteristics in sedimentary basins. In sites characterized by 1D response HVNSR is able to detect the resonance frequency of sediments (f0) to be related with their thickness and velocity. In quasi-1D geological situation, a smooth variation in the resonance frequency suggests some variation in the thickness of the soft sedimentary layers or in their velocity. In the case of sharp lateral variation of the subsoil, as in presence of morphological steps or buried faults in the bedrock, the noise wave-field becomes more complex and spectral ratios show some directional effect strictly related to the presence of the lateral heterogeneity (Matsushima et al. 2014). In this work we focus our attention on the detection of a buried shallow tectonic element known in bibliography (Galadini, Galli 1999) as the Luco dei Marsi fault, located in the western margin of the Fucino basin (central Appenines, Italy). We performed simultaneous ambient noise measurements using MarsLite digitizers equipped with Lennarts 3d-5s velocimeters along a transect, with inter-station distance between 30 and 50 meters, which crosses perpendicularly the surface projection of fault line. The collected data, analyzed with classical HVNSR technique, show some complexities in the f0 distribution compatible with the presence of the buried fault. In detail, our results highlight a 1D response with a clear resonance peak for the stations located away from the fault. Moving closer to the fault line, where the 1D condition is not verified, the resonance peak becomes broader. Directional analysis of spectral ratios suggests the dependence of the noise wave-field to the presence of the fault line. Close to the geological feature, results of directional analysis show a doubling in the resonance frequency with relative amplitudes changing for fault-parallel and fault-normal direction of polarization. To support with an independent approach our observations, an electrical resistivity tomography was performed along the transect whose results show the presence of a clear step in a high resistivity shallow layer that can be assumed as the bedrock. After this analysis we decided to extend the ambient noise transect towards the centre of the basin where no fault line is mapped and where we expected a smooth lowering of f0 values due to the deepening of the bedrock. This feature was really observed for a while but at a distance between 400 and 500 meters from the Luco fault we detected again some anomaly in HVNSR data with a doubling of resonance frequency and relative amplitudes depending from the direction of polarization. This observation suggests the presence of deeper tectonic element parallel to the Luco fault. As a conclusion of our work we believe that HVNSR and polarization analysis can represent a quick and fast method to hypothesize the presence of buried discontinuity in the subsoil and can be usefully used to guide the positioning of more sophisticated geophysical analysis aimed at mapping their geometries.74 42 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , ESG6 BLIND PREDICTION. STEP1 BY INGV AND ENEA TEAM
This paper describes the analysis performed within the ESG6 blind prediction step 1, devoted to the retrieval of the shear-wave velocity (Vs) structure at a target site in Kumamoto city. Ambient vibration data were analysed by different techniques. Horizontal-to-vertical spectral ratios were calculated showing resonance peaks around 0.3 and 1.1 Hz. Three methods were applied for surface-wave dispersion curve (DC) retrieval: cross-correlation (CC), modified spac (MSPAC) and high resolution F-K (RTBF). Vertical components were analysed to retrieve fundamental Rayleigh-wave DCs while horizontal motions allowed to extract Love-wave DC by RTBF. The Rayleigh-wave DCs from all methods are in good agreement. They were used as a target for numerical inversion jointly with Love-wave DC and Rayleigh-wave ellipticity curve obtained for one station. The retrieved Vs profiles are presented, and the comparison of our results with the best Vs model provided by the ESG6 committee is also discussed.50 97 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Microzonazione sismica di un centro abitato di piccole dimensioni: il caso studio di Sant’Agata Fossili (AL)
In questo lavoro sono descritte le attività svolte nell’ambito del Progetto Europeo Strategico RISKNAT riguardanti l’analisi di microzonazione di Sant’Agata Fossili (AL). Sono in particolare descritte tutte le indagini ed analisi numeriche condotte al fine di ottenere una microzonazione sismica di livello 3 secondo quanto previsto nelle recenti linee guida nazionali degli. Al fine inoltre di valutare le ricadute di tipo applicativo di una corretta microzonazione sismica del territorio, sono state realizzate delle simulazioni di scenario adottando come riferimento gli spettri di risposta ottenuti dall’analisi di microzonazione. Le valutazioni di scenario ottenute sono state infine confrontate con le previsioni di scenario realizzabili a priori sulla base dell’adozione degli spettri di risposta definiti nelle Norme Tecniche per le Costruzioni.220 459 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Variations of local seismic response in Benevento (Southern Italy) using earthquakes and ambient noise recordings
(2005-03-16); ; ; ;Improta, L.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, ItaliaDi Giulio, G.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, ItaliaThe city of Benevento (Southern Italy) has been repeatedly struck by large historical earthquakes. A heterogeneous geologic structure and widespread soft soil conditions make the estimation of site effects crucial for the seismic hazard assessment of the city. From 2000 until 2004, we installed seismic stations to collect earthquake data over zones with different geological conditions. Despite the high level of urban noise, we recorded more than 150 earthquakes at twelve sites. This data set yields the first, well documented experimental evidence for weak to moderate local amplifications. We investigated site effects primarily by the classical spectral ratio technique (CSR) using a rock station placed on the Benevento hill as reference. All sites in the Calore river valley and in the eastern part of the Benevento hill show a moderate high-frequency (f > 4 Hz) amplification peak. Conversely, sites in the Sabato river valley share weak-to-moderate amplification in a wide frequency band (from 1-2 to 7-10 Hz), without evident frequency peaks. Application of no-reference-site techniques to earthquake and noise data confirms the results of the CSRs in the sites of the Calore river valley and of the eastern part of the Benevento hill, but fails in providing indications for site effects in the Sabato river valley, being the H/V ratios nearly flat. One-dimensional modeling indicate that the ground motion amplification can be essentially explained in terms of a vertically varying geologic structure. High-frequency narrow peaks are caused by the strong impedance contrast existing between near-surface soft deposits and stiff cemented conglomerates. Conversely, broad-band amplifications in the Sabato river valley are likely due to a more complex layering with weak impedance contrasts both in the shallow and deep structure of the valley145 26 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , FORTI EFFETTI DI AMPLIFICAZIONE DEL MOTO IN ZONA DI FAGLIA DURANTE LA SEQUENZA SISMICA DEL 2009 IN ABRUZZO
(2010-10-26); ; ; ; Negli anni 1997-1998, durante la sequenza dell’Umbria-Marche, la stazione accelerometrica di Nocera Umbra superò ripetutamente, per terremoti di magnitudo > 5, il picco di accelerazione di 0.5 g. Tali valori furono i maggiori mai registrati in Italia, e apparvero subito inusuali per terremoti di faglia normale a magnitudo moderate. Una serie di studi del sito della stazione permise di attribuire l’ampiezza anomala a un forte effetto di amplificazione locale prodotto dalle variazioni verticali della velocità delle onde di taglio nella roccia danneggiata di una faglia sub-verticale in prossimità della stazione. Anche durante i terremoti della sequenza Aquilana si sono trovate evidenze di effetti analoghi. La stazione a banda larga FAGN, in prossimità della faglia di San Demetrio, ha mostrato una accentuata variabilità dell’ampiezza delle sue registrazioni, con valori che superano fino ad un fattore 10 le ampiezze delle stazioni vicine. Mediante un’analisi su 350 terremoti si è trovato che le massime amplificazioni avvengono per terremoti localizzati a sud-ovest della stazione, in posizione favorevole alla propagazione nella zona di faglia dalla sorgente al ricevitore. Utilizzando metodi sia analitici che numerici è stato possibile attribuire gli effetti osservati alle eterogeneità di una zona di faglia larga 300-400 m e profonda 3 km, approssimativamente, con una riduzione di velocità di circa il 30% rispetto alla roccia non deformata. Anche il forte impulso di spostamento di 40 cm picco-picco registrato durante la scossa principale a Castello d’Ocre da una stazione GPS (CADO) con campionamento a 10 Hz non trova giustificazione plausibile se non modellando un effetto di risonanza in prossimità dello strumento. In questo caso è possibile generare modelli che riproducano l’osservazione usando valori della larghezza della zona di faglia di qualche centinaio di metri con forti riduzioni della velocità delle onde di taglio rispetto ai blocchi rigidi adiacenti. Queste osservazioni confermano la potenziale pericolosità del territorio in prossimità delle zone di faglia, nonostante non siano emerse durante il terremoto dell’Aquila chiare evidenze di anomalie del danno persistenti lungo le faglie. Recenti studi in California sembrano mettere in luce l’estrema variabilità delle onde intrappolate nelle zone di faglia, per cui l’effetto appare sporadicamente sia per quanto riguarda le stazioni di registrazione lungo la faglia che per quanto riguarda le zone-sorgenti nella faglia capaci di generare onde intrappolate.275 116 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Deliverable D19: Influence of alluvium filled basins and edge effects on displacement response spectra
(2007-07); ; ; ; Several cases of strong motion data recorded in alluvial basins show very high amplification effects that exceed, at medium and long periods, those predicted by empirical relations or included in standard reference codes. Among others, we recall here the earthquakes of San Fernando (1972), Northridge (1994) (BSSA, 1996) and the Umbria-Marche sequence of 1997, during which the shaking recorded in the Gubbio Plain (Pacor et al, 2007) provided strong evidence of the phenomenon: extremely high spectral amplification values (higher than reference codes) for 2 < T < 4 s (see Fig. 4). The main reason why these amplifications (“basin effects”) take place lies in the generation, by diffraction at the edges of the valley, of long period surface waves that travel horizontally in the upper sediments of the valley. While the influence of alluvium filled basins on site response has been the subject of substantial research, the resulting modifications on the response spectra at the basin surface (especially for T > 1 - 2 s) has not been as thoroughly investigated (see e. g. Chávez e Faccioli, 2000) despite its importance in structural design. Significant previous studies tried to estimate basin amplification effects through the analysis of strong-motion data and most of them quantified basin geometry only in terms of sediment depth (Trifunac and Lee, 1978), introducing such term in newly developed attenuation models (Campbell, 1997; Field, 2000; Lee and Anderson, 2000). Other studies tried to relate basin effects also to the relative location of source and site position in the basin (Choi et al., 2005), or to the distance to the basin edge (Joyner, 2000). In the S5 project, specific parametric studies involved two different types of basins (both typical of the Italian Peninsula): “enclosed” basins and “open” basins. Results gave great insight of how basin effects amplify seismic motion in connection with the geometry of the basin, with the fault mechanism and with the different valley-fault configurations. Critical in all analyses is the value of the fundamental 1D vibration period of valley centre, T01D, that acts as the theoretical upper limit to 2D basin amplification effects, as stated in Chàvez-García and Faccioli (2000). Its calculation appears thus crucial in the study of the seismic response of valleys and basins. In addition, a detailed study has been devoted to the identification and classification of alluvium filled basins in Italy, and particularly to the parameters that the previous analyses highlighted as the most critical ones in the modification of response spectra.178 519
