Skip to main content
The search returned 3 results
Now showing 1 - 3 of 3
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Lithological and stress anisotropy control large-scale seismic velocity variations in tight carbonates

    Our knowledge of subsurface structures often derives from seismic velocities that are measured during seismic acquisition surveys. These velocities can greatly change due to lithological, fracture frequencies and/or effective pressure/temperature variations. However, the influence of such intrinsic lithological properties and environmental conditions at the large scale is poorly understood due to the lack of comprehensive datasets. Here, we analyze 43 borehole-derived velocity datasets of 3 end-member tight carbonate sequences from Central Italy, including massive pure limestone (Calcare Massiccio, CM), thick-layered (20-50 cm) pure limestone (Maiolica, MA), and thin-layered (2-20 cm) marly limestone (Calcareous Scaglia, CS). Our results show that the main rock parameters and environmental conditions driving large scale velocity variations are bedding and paleostresses, while mineralogical composition and current tectonic stress also play a role. For each of the 3 end-members, measured VP values vary differently with depth, as the thin-layered CS units show a clear increase in Vp, while velocity slightly increases and remains constant for the thick-layered MA and massive CM units, respectively. Such observations show that velocities are affected by specific characteristics of lithological discontinuities, such as the thickness of bedding. Counterintuitively, larger Vp values were recorded in the deformed mountain range than in the undeformed foreland suggesting that higher paleo-stresses increase velocity values by enhancing diagenesis and healing of discontinuities. Our results thus demonstrate that large scale velocity variations are strictly related to variation of lithological properties and to the geological and tectonic history of an area. We suggest that such lithological and environmental controls should be taken into account when developing velocity and mechanical models for tectonically active regions of the Mediterranean Area, where earthquakes mostly nucleate and propagate through carbonate formations, and for resource exploration in fractured carbonate reservoirs.
      39  119
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    The role of shale content and pore-water saturation on frictional properties of simulated carbonate faults

    The presence of weak phyllosilicates in mature carbonate fault zones has been invoked to explain weak faults. However, the relation between frictional strength, fault stability, mineralogical composition, and fabric of fault gouge, composed of strong and weak minerals, is poorly constrained. We used a biaxial apparatus to systematically shear different mixtures of shale (68% clay, 23% quartz and 4% plagioclase) and calcite, as powdered gouge, at room temperature, under constant normal stresses of 30, 50, 100 MPa and under room-dry and pore fluid-saturated conditions, i.e. CaCO3-equilibrated water. We performed 30 friction experiments during which velocity-stepping and slide-hold-slide tests were employed to assess frictional stability and to measure frictional healing, respectively. Our frictional data indicate that the mineralogical composition of fault gouges significantly affects frictional strength, stability, and healing as well as the presence of CaCO3-equilibrated water. Under room-dry condition, the increasing shale content determines a reduction in frictional strength, from μ = 0.71 to μ = 0.43, a lowering of the healing rates and a transition from velocity-weakening to velocity-strengthening behavior. Under wet condition, with increasing shale content we observe a more significant reduction in frictional strength (μ = 0.65–0.37), a near-zero healing and a velocity strengthening behavior. Microstructural investigations evidence a transition from localized deformation promoted by grain size reduction, in calcite-rich samples, to a more distributed deformation with frictional sliding along clay-enriched shear planes in samples with shale content greater than 50%. For faults cutting across sedimentary sequences composed of carbonates and clay-rich sediments, our results suggest that clay concentration and its ability to form foliated and interconnected networks promotes important heterogeneities in fault strength and slip behavior.
      51  2
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Considerazioni sull'origine delle acque presenti in livelli sabbiosi profondi del Tavoliere di Puglia

    Sandy levels bearing bicarbonate-sodium waters, having hydraulic heads sometimes higher than ground level, have been observed during drillings in the Pliocene-Pleistocene clayey formation of the Tavoliere area. Hypotheses on origin and renewal capability of groundwater of these levels have been put forward considering usual hydrogeological parameters from discharge tests and geochemical and isotopic data.
      305  772