Skip to main content
The search returned 4 results
Now showing 1 - 4 of 4
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Influence of thermal and mechanical cracks on permeability and elastic wave velocities in a basalt from Mt. Etna volcano subjected to elevated pressure

    (2011) ; ; ; ;
    Fortin, J.
    We report simultaneous laboratory measurements of seismic velocities and fluid permeability on lava flow basalt from Etna (Italy). Results were obtained for dry and saturated samples deformed under triaxial compression. During each test, the effective pressure was first increased up to 190 MPa to investigate the effect of pre-existing crack closure on seismic properties. Then, the effective pressure was unloaded down to 20 MPa, a pressure which mirrors the stress field acting under a lava pile of approximately 1.5–2 km thick, and deviatoric stress was increased until failure of the specimens. Using an effective medium model, the measured elastic wave velocities were inverted in terms of two crack densities: ρi the crack density of the pre-existing thermal cracks and ρv the crack density of the stress-induced cracks. In addition a link was established between elastic properties (elastic wave velocities Vp and Vs) and permeability using a statistical permeability model. Our results show that the velocities increase with increasing hydrostatic pressure up to 190 MPa, due to the closure of the pre-existing thermal cracks. This is interpreted by a decrease of the crack density ρi from ~ 1 to 0.2. The effect of pre-existing cracks closure is also highlighted by the permeability evolution which decreases of more than two orders of magnitude. Under deviatoric loading, the velocities signature is interpreted, in the first stage of the loading, by the closure of the pre-existing thermal cracks. However, with increasing deviatoric loading newly-formed vertical cracks nucleate and propagate. This is clearly seen from the velocity signature and its interpretation in term of crack density, from the location of the acoustic emission sources, and from microstructural observations. This competition between pre-existing cracks closure and propagation of vertical cracks is also seen from the permeability evolution, and our study shows that mechanically-induced cracks has lesser influence on permeability change than pre-existing thermal cracks.
      115  20
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Initiation and propagation of compaction bands in dry and wet sandstones

    (2007-09-25) ; ; ; ;
    Stanchits, S.; GFZ, Potsdam, Germany
    see Abstract Volume
      98  266
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Stress induced elastic anisotropy of the Etnean basalt: Theoretical and laboratory examination

    A theory, the stress-sensitivity approach, has been developed, which relates the elastic moduli of anisotropic rocks to the stress tensor and pore pressure for an arbitrary symmetry of the applied load. The theory explains the stress-induced changes of seismic velocities in terms of stress-induced changes of the pore space geometry. The stress dependent anisotropy is described in terms of Thomsen’s anisotropy parameters, g and d. To test the theory we analyze the laboratory (high frequency) results of deformation of an isotropically crack damaged dry lava flow basalt from Mt. Etna volcano. The theory states that, under an anisotropic (i.e. axisymmetric triaxial) load and in the case of an initially isotropic rock, (1) the anisotropy parameters are linear functions of the stress exponentials (i. e. exponential functions of principal stress components) and (2) the ratio of these anisotropy parameters as a function of the stress is constant. In order to verify these relationships, the stress exponentials and the anisotropy parameters based on the measured velocities are computed as well as the expected ratio of the Thomsen’s parameters. Our experimental results are in very good agreement with the theoretically predicted relations.
      135  21
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Ultrasonic velocities, acoustic emission characteristics and crack damage of basalt and granite

    (2006) ; ; ;
    Stanchits, S.; Department 3.2, Geo Forschungs Zentrum Potsdam, Telegrafenberg D420, 14473, Potsdam,
    ;
    Vinciguerra, S.; Istituto Nazionale di Geofisica e Vulcanologia, Sezione Roma1, Roma, Italia
    Acoustic emissions (AE), compressional (P), shear (S) wave velocities, and volumetric strain of Etna basalt and Aue granite were measured simultaneously during triaxial compression tests. Deformation-induced AE activity and velocity changes were monitored using twelve P-wave sensors and eight orthogonally polarized S-wave piezoelectric sensors; volumetric strain was measured using two pairs of orthogonal strain gages glued directly to the rock surface. P-wave velocity in basalt is about 3 km/s at atmospheric pressure, but increases by > 50% when the hydrostatic pressure is increased to 120 MPa. In granite samples initialP-wave velocity is 5 km/s and increases with pressure by<20%. The pressure-induced changes of elastic wave speed indicate dominantly compliant low-aspect ratio pores in both materials, in addition Etna basalt also contains high-aspect ratio voids. In triaxial loading, stress-induced anisotropy of Pwave velocities was significantly higher for basalt than for granite, with vertical velocity components being faster than horizontal velocities. However, with increasing axial load, horizontal velocities show a small increase for basalt but a significant decrease for granite. Using first motion polarity we determinedAE source types generated during triaxial loading of the samples. With increasing differential stressAEactivity in granite and basalt increased with a significant contribution of tensile events. Close to failure the relative contribution of tensile events and horizontal wave velocities decreased significantly. A concomitant increase of doublecouple events indicating shear, suggests shear cracks linking previously formed tensile cracks.
      236  33