Skip to main content
The search returned 4 results
Now showing 1 - 4 of 4
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Preliminary results on the response of some springs of the Sibillini Mountains area to the 2016-2017 seismic sequence

    Abstract: The dynamic of groundwater systems feeding several springs of the Sibillini Mountains was deeply affected by nine Mw 5.0÷6.5 seismic events occurred in central Italy starting from August 2016. The strongest shock occurred on October 30th 2016 about 5 km NNE of Norcia Town, 9 km below the surface, as a result of upper crust normal faulting on the nearly 30 km-long Mt Vettore - Mt Bove fault system, a NW-SE trending, SW-dipping fault system outcropping on the western slope of Mt Vettore, the highest peak of Sibillini Mountains. Soon after this event, a general increase of springs and rivers discharge and groundwater levels was observed both in the Visso and Norcia areas, west of the Sibillini Mountains. In the Visso area the hydrogeological changes due to the seismic sequence exhausted in the 2019, while nowadays both discharges and groundwater levels are still higher than before in the Norcia area. Discharge data of the main springs located east, south-east of the Sibillini Mountains were analysed to verify whether the general increase observed on the western side was associated to a decrease on the eastern and southern-east area. The results show that the springs located on the eastern side and southern-east side of Mt Vettore experienced a significant long-term discharge decrease. In this preliminary work, the analysis of the historical discharge series of the Pescara di Arquata spring (SE of Mt Vettore), and its relationship with the Standard Precipitation Index (SPI) shows that the very low discharge values recorded during the post-seismic period are not associated with SPI as low as documented in the past for similar discharges. Moreover, the stable isotopic composition of Pescara di Arquata water during the post-earthquake period is slightly different from that measured before the seismic events; this suggests that a lower amount of water having more enriched isotopic δ18O content reaches the spring after the seismic sequence. These aspects seem to indicate that groundwater circulation in the southern-east area of Sibillini Mountains has been affected by the 2016-2017 seismic sequence
      164  153
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Radon - Chapter 5

    (Publication Office of the European Union, 2019) ; ; ; ;
    Radon isotopes (222Rn, 220Rn) are noble, naturally occurring radioactive gases. They originate from the alpha decay of radium isotopes (226Ra, 224Ra), which occur in most materials in the environment, i.e. soil, rocks, raw and building materials. Radon is also found in ground and tap water. The two radon isotopes are chemically identical, but they have very different halflives: 3.82 days for radon (222Rn) and 56 seconds for thoron (220Rn). Thus, they behave very differently in the environment. Both isotopes are alpha-emitters; their decay products are polonium, bismuth and lead isotopes. The main source of radon in air (indoor or outdoor) is soil, where radon concentrations are very high and reach tens of Bq/m3. Radon release from soil into the atmosphere depends on radium (226Ra) concentration in soil, soil parameters (porosity, density, humidity) and weather conditions (e.g. air temperature and pressure, wind, precipitation). Outdoor radon concentrations are relatively low and change daily and seasonally. These changes may be used to study the movement of air masses and other climatic conditions. Radon gas enters buildings (homes, workplaces) through cracks, crevices and leaks that occur in foundations and connections between different materials in the building. This is due to temperature and pressure differences between indoors and outdoors. Indoor radon is the most important source of radiation exposure to the public, especially on ground floor. Radon and its decay products represent the main contributor to the effective dose of ionising radiation that people receive. Radon is generally considered as the second cause of increased risk of lung cancer (after smoking). The only way to assess indoor radon concentration is to make measurements. Different methods exist, but the most common one is to use track-etched detectors. Such detectors may be used to perform longterm (e.g. annual) measurements in buildings. The exposure time is important because indoor radon levels change daily and seasonally. Moreover, radon concentration shows a high spatial variation on a local scale, and is strongly connected with geological structure, building characteristics and ventilation habits of occupants. A European map of indoor radon concentration has been prepared and is displayed. It is derived from survey data received from 35 countries participating on a voluntary basis.
      174  151
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Monitoring Active Volcanos Using Aerial Images and the Orthoview Tool

    In volcanic areas, where it can be difficult to perform direct surveys, digital photogrammetry techniques are rarely adopted for routine volcano monitoring. Nevertheless, they have remarkable potentialities for observing active volcanic features (e.g., fissures, lava flows) and the connected deformation processes. The ability to obtain accurate quantitative data of definite accuracy in short time spans makes digital photogrammetry a suitable method for controlling the evolution of rapidly changing large-area volcanic phenomena. The systematic acquisition of airborne photogrammetric datasets can be adopted for implementing a more effective procedure aimed at long-term volcano monitoring and hazard assessment. In addition, during the volcanic crisis, the frequent acquisition of oblique digital images from helicopter allows for quasi-real-time monitoring to support mitigation actions by civil protection. These images are commonly used to update existing maps through a photo-interpretation approach that provide data of unknown accuracy. This work presents a scientific tool (Orthoview) that implements a straightforward photogrammetric approach to generate digital orthophotos from single-view oblique images provided that at least four Ground Control Points (GCP) and current Digital Elevation Models (DEM) are available. The influence of the view geometry, of sparse and not-signalized GCP and DEM inaccuracies is analyzed for evaluating the performance of the developed tool in comparison with other remote sensing techniques. Results obtained with datasets from Etna and Stromboli volcanoes demonstrate that 2D features measured on the produced orthophotos can reach sub-meter-level accuracy.
      281  516
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Modelling of the 2001 Lava Flow at Etna Volcano by a Cellular Automata Approach

    The 2D Cellular Automata model, MAGFLOW, simulates lava flows and an algorithm based on the Monte Carlo approach solves the anisotropic flow direction problem. The model was applied to reproduce a lava flow formed during the 2001 Etna eruption. This eruption provided the opportunity to verify the ability of MAGFLOW to simulate the path of lava flows. made possible due to the availability of the necessary data for both modeling and subsequent validation. MAGFLOW reproduced quite accurately the spread of flow. A good agreement was highlighted between the simulated and observed length on steep slopes, whereas the area covered by the lava flow tends to be overestimated. The major inconsistencies found in the comparison between simulated and observed lava flow due to neglecting the effects of ephemeral vent formation.
      283  19