CNR-IGG Firenze
11 results
Filters
Settings
The search returned 11 results
Now showing 1 - 10 of 11
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , 669 1228 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , CO2 reactive transport simulations in an Italian deep saline aquifer
(2009-09); ; ; ; In this study numerical simulations of reactive transport in an off-shore deep saline aquifer for the geological sequestration of carbon dioxide are presented and discussed. The main goals are to assess: i) the CO2 injection impact in the reservoir and ii) the cap-rock stability, both being strategic requisites for feasibility studies that are about to be started in Italy. The stratigraphic succession is characterized by a sedimentary succession: from Triassic anhydrites to Jurassic Tuscan calcareous units, up to Cretaceous calcarenites, belonging to the Liguride units, and Quaternary shallow marine sediments. Stratigraphic data from a deep well indicate that below an 1,800 m thick cap-rock, constituted by allochtonous marly calcarenites and clay marls, a regional deep saline aquifer is present. This aquifer, hosted in six Late Triassic to Early Jurassic formations, belonging to the Tuscan Nappe units, consists of porous limestone (mainly calcite) and marly limestone deposits at 1900-3100 m b.s.l. A common problem working with off-shore closed wells, where only the well-log information are available, is that to obtain reliable physico-chemical parameters (e.g. petrophysical and mineralogical) to be used for numerical simulations. Available site-specific data include only basic physical parameters such as temperature, pressure, and salinity of the formation waters. Bulk and modal mineralogical composition were obtained after sampling each formation in contiguous on-shore zones. Mineralogy was determined by X-Ray diffraction analysis coupled with Rietfield refinement. The latter was performed using Maud v2.2. The surface reactive area of minerals was assumed as geometric area of a truncated sphere calculated on the basis of Scanning Electronic Microscopy analysis. Porosity and permeability were inferred by the well-log data along with the use of boundary conditions such as surficial measurements and temperature profiles. The chemical composition of the aquifer pore water is unknown. As a consequence, this was calculated by batch modeling, assuming thermodynamic equilibrium between minerals and a NaCl (0.45 M) equivalent brine at reservoir conditions (up to 118 °C and 300 bars). The reconstructed dataset represented the base of numerical simulations to evaluate the potential geochemical impact of CO2 storage and to quantify water-gas-rock reactions. Three dimensional simulations were performed by the TOUGHREACT code via the implementation to the source code and the correction of the chemical parameters at the theoretical CO2 injection pressure. A re-interpretation of the available seismic reflection data was carried out to: i) define the 3D geometry, and ii) evaluate the volume of the geological structure potentially suitable for CO2 storage. In particular the main surfaces where physicochemical modeling was applied, i.e. the top and the bottom of the cap-rock units and the spill point surface, to better define the 3D geometry of the potential injection reservoir, were reconstructed. Reactive transport simulations were conducted under multiphase advection, aqueous diffusion, gas phase participation in multiphase fluid flow and geochemical reaction in non-isothermal conditions. Feedbacks between flow and geochemical processes were taken into account to evaluate changes in porosity and permeability as kinetic reactions were proceeding. Twenty years of CO2 injection at the rate of 1.5 Mt/year were simulated, whereas water-gas-rock interactions between CO2-rich brines and minerals over a period of 100 years were performed. Preliminary results suggest that injected CO2 can safely be retained in the reservoir by mineral trapping and that the cap-rock can be considered as efficient barrier.275 214 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , BARRIER EFFECT IN CO2 CAPTURE AND STORAGE FEASIBILITY STUDY
(2009-09); ; ; ; CO2 Capture & Storage (CCS) in saline aquifer is one of the most promising technologies for reducing anthropogenic emission of CO2. Feasibility studies for CO2 geo-sequestration in Italy have increased in the last few years. Before planning a CCS plant an appropriate precision and accuracy in the prediction of the reservoir evolution during injection, in terms of both geochemical calculation and fluid flow properties, is demanded. In this work a geochemical model will be presented for an offshore well in the Tyrrhenian Sea where the injection of 1.5 million ton/year of CO2 is planned. The dimension of the trapping structure requires to study an area of about 100 km2 and 4 km deep. Consequently, three different simulations were performed by means of TOUGHREACT code with Equation Of State module ECO2N. The first simulation is a stratigraphic column with a size of 110*110*4,000 meters and a metric resolution in the injection/cap-rock area (total of 8,470 elements), performed in order to asses the geochemical evolution of the cap-rock and to ensure the sealing of the system. The second simulation is at large scale in order to assess the CO2 path from the injection towards the spill point (total of about 154,000 elements). During this simulation, the effect of the full coupling of chemistry with fluid flow and a relevant effect in the expected CO2 diffusion velocity was recognized. Owing to the effect of chemical reaction and coupling terms (porosity/permeability variation with mineral dissolution/precipitation), the diffusion velocity results to be 20% slower than in a pure fluid flow simulation. In order to give a better picture of this 'barrier' effect, where the diffusion of the CO2-rich acidic water into the carbonate reservoir originates a complex precipitation/dissolution area, a small volume simulation with a 0.1 m grid was elapsed. This effect may potentially i) have a big impact on CO2 sequestration due to the reduction of available storage volume reached by the CO2 plume in 20 years and/or the enhanced injection pressure and ii) outline the relevance of a full geochemical simulation in an accurate prediction of the reservoir properties.224 360 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Overview of the geochemical modeling on CO2 capture & storage in Italian feasibility studies
(2009-06); ; ; ; CO2 Capture & Storage in saline aquifers is presently one of the most promising technologies for reducing anthropogenic emissions of CO2. In these sites the short-longterm consequences of CO2 storage into a deep reservoir can be predicted by numerical modelling of geochemical processes. Unfortunately a common problem working with off-shore closed wells, where only the well-log information are available, is to obtain physico-chemical data (e.g. petrophysical and mineralogical) needed to reliable numerical simulations. Available site-specific data generally include only basic physical parameters such as temperature, pressure, and salinity of the formation waters. In this study we present a methodological procedure that allows to estimate and integrate lacking information to geochemical modelling of deep reservoirs such as: i) bulk and modal mineralogical composition, ii) porosity and permeability of the rock obtained from heat flow measurements and temperature, iii) chemical composition of formation waters (at reservoir conditions) prior of CO2 injection starting from sampling of analogue outcropping rock formations. The data sets in this way reconstructed constitute the base of geochemical simulations applied on some deep-seated Italian carbonatic and sandy saline aquifers potentially suitable for geological CO2 storage. Numerical simulations of reactive transport has been performed by using the reactive transport code TOUGHREACT via pressure corrections to the default thermodynamic database to obtain a more realistic modelling. Preliminary results of geochemical trapping (solubility and mineral trapping) potentiality and cap-rock stability as strategic need for some feasibility studies near to be started in Italy are here presented and discussed.166 219 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , RECONSTRUCTION OF POROSITY PROFILE OF AN OFF-SHORE DEEP WELL AND INPUT DATA FOR THE GEOCHEMICAL MODELING OF CO2 STORAGE IN A CARBONATE SALINE AQUIFER, IN ITALY.
(2009-03-16); ; ; ; CO2 Capture & Storage (CCS) is presently one of the most promising technologies for reducing anthropogenic emissions of CO2. The numerical modeling procedures of geochemical processes are one of the few approaches for investigating the short-long-term consequences of CO2 storage into a deep reservoir. We present the results of a new approach for the reconstruction of thermo-physical properties of an off-shore deep well (situated in the medium Tyrrhenian Sea, only 5 miles from the coast, in the frame of a distensive and relatively high heat flux regime as a whole,with good outcrops, on-shore, of its stratigraphy includes six Late Triassic-Early Jurassic carbonatic formations at the depth of 2500-3700 m b.s.l). We used the well-log coupled with temperature profile and new mineralogical analyses of the outcrops geological formations, being the original core data lacking. This kind of procedure is new as a whole, and it is useful to create background petro-physical data, for reservoir engineering numerical simulations both of mass-transport and geochemical as well as geo-mechanical, in order to asses its general properties, without re-opening the well itself for industrial use, such as CO2 geological storage. The profile of thermal capacity and conductivity, as well as porosity and permeability resulted very well constrained and detailed for further numerical simulation uses. Porosity is a very important parameter for reservoir engineering, mainly for numerical simulations including geochemical modelling, being strongly necessary for CO2 geological storage feasibility studies, because it allows to compute: i) the reservoir storage capacity for each trapping mechanisms (some algorithms are discussed in the presentation) and ii) the water/rock ratio (one of the input parameter requested by the geochemical software codes). A common problem, working with closed wells with, available the well-log report only, is to obtain data on the thermo-physical properties of the rock. Usually the available well-log report the temperature profile measured during drilling, the mud-loss and some other information on water and gas phase presence. In this work we present a procedure that allow to estimate porosity and permeability of the rock formation from the well-log data joint with a rough mineralogical analyses of the corresponding geological formations outcrop with the use of a boundary condition such as shallow heat flow measurements; a similar approach were presented from some authors that dealt with similar problems e.g. Singh V.K., (2007). The analyses of the rock samples proceed by using i) petro-graphical analyses; ii) calcimetry with Dietrich-Fruhling apparatus in order to analyse the carbonate content of each sample; iii) XRD Rietveld analyses in order to quantify the major mineralogy of each sample and to apply the dolomite correction to the results of calcimetry determination. Rietveld quantification procedure were performed by using Maud v 2.2.; iv) SEM analyses have been accomplished later in details. Successively, hints about the subsequent geochemical modelling approach are presented. Chemical composition of the aquifer pore water has been has been inferred by batch modeling assuming thermodynamic equilibrium between minerals and a NaCl equivalent brine at reservoir conditions (up to 70 °C and 200 bar). Numerical simulations has been carried out by the PRHEEQC (V2.11) Software Package via corrections to the code default thermodynamic to obtain a more realistic modeling.170 216 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Restricted , Geochemical modeling of CO2 storage in deep reservoirs: The Weyburn Project (Canada) case study
Geological storage is presently one of the most promising options for reducing anthropogenic emissions of CO2. Among the several projects investigating the fate of CO2 stored at depth, the EnCana's CO2 injection EOR (Enhancing Oil Recovery) project at Weyburn (Saskatchewan, Canada) is the most important oil production development that hosts an international monitoring project. In the Weyburn EOR Project CO2 is used to increase recovery of heavy oil from the Midale Beds, a Mississippian reservoir consisting of shallow marine carbonate, where about 3 billions standard m3 of supercritical CO2 have been injected since 2000 with an injection rate of 5000 ton/day. In this work the available dataset (bulk mineralogy of the reservoir, gas-cap composition and selected preand post-CO2 injection water samples) provided by the International Energy Agency Weyburn CO2 Monitoring & Storage Project has been used in order to: i) reconstruct the pre-injection reservoir chemical composition (including pH and the boundary conditions at 62 °C and 15 MPa); ii) assess the evolution of the reservoir subjected to CO2 injection and predict dissolution/precipitation processes of the Weyburn brines over 100 years after injection; iii) validate the short-term (September 2000–2003) evolution of the in situ reservoir fluids due to the CO2 injection, by comparing the surface analytical data with the composition of the computed depressurized brines. To achieve these goals the PRHEEQC (V2.14) Software Package was used with both modified thermodynamic database and correction for supercritical CO2 fugacity. The oil–gas–water interaction and the non-ideality of the gas phase (with exception of CO2) were not considered in the numerical simulations. Despite intrinsic limitations and uncertainties of geochemical modeling, the main results can be summarized, as follows: 1) the calculated pre-injection chemical composition of the Midale Beds brine is consistent with the analytical data of the waters collected in 2000 (baseline survey), 2) the main reservoir reactions (CO2 and carbonate dissolution) take place within the first year of simulation, 3) the temporal evolution of the chemical features of the fluids in the Weyburn reservoir suggests that CO2 can safely be stored by solubility (as CO2(aq)) and mineral trapping (via dawsonite precipitation). The short-term validation performed by calculating chemical composition of the reservoir fluids (corrected for surface conditions) after the simulation of 3 years of CO2 injection is consistent (error ≤5%) with the analytical data of the wellhead water samples collected in 2003, with the exception of Ca and Mg (error N90%), likely due to complexation effect of carboxilic acid.541 2638 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , RECONSTRUCTION OF POROSITY PROFILE IN AN OFFSHORE WELL
(2008-09-22); ; ; ; Montegrossi, G.; CNR-IGG FirenzeWe presents the results of a new approach for the reconstruction of thermo-physical properties of deep well from the well log and mineralogical analisys of the outcrops formation. This kind of procedure are generally new, and they are useful for creating the background data for reservoir engeneers and geochemist for modelling a well in order to asses its properties prior of re-opening the well itself for industrial use, such as CO2 sequestration. We used the temperature profile obtained from the well log and the bulk mineralogy analysed from the corresponding formation outcrops. The profile of thermal capacity and conductivity, and porosity and permeability as well, result well constrained and detaile for further use.120 407 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Mineralogy and geochemical trapping of CO2 in an Italian carbonatic deep saline aquifer: preliminary results
(2008-04-18); ; ; ; CO2 Capture & Storage (CCS) is presently one of the most promising technologies for reducing anthropogenic emissions of CO2 . Among the several potential geologi- cal CO2 storage sites, e.g. depleted oil and gas field, unexploitable coal beds, saline aquifers, the latter are estimated to have the highest potential capacity (350-1000 Gt CO2 ) and, being relatively common worldwide, a higher probability to be located close to major CO2 anthropogenic sources. In these sites CO2 can safely be retained at depth for long times, as follows: a) physical trapping into geologic structures; b) hy- drodynamic trapping where CO2(aq) slowly migrates in an aquifer, c) solubility trap- ping after the dissolution of CO2(aq) and d) mineral trapping as secondary carbon- ates precipitate. Despite the potential advantages of CO2 geo-sequestration, risks of CO2 leakage from the reservoir have to be carefully evaluated by both monitoring techniques and numerical modeling used in “CO2 analogues”, although seepage from saline aquifers is unlikely to be occurring. The fate of CO2 once injected into a saline aquifer can be predicted by means of numerical modelling procedures of geochemical processes, these theoretical calculations being one of the few approaches for inves- tigating the short-long-term consequences of CO2 storage. This study is focused on some Italian deep-seated (>800 m) saline aquifers by assessing solubility and min- eral trapping potentiality as strategic need for some feasibility studies that are about to be started in Italy. Preliminary results obtained by numerical simulations of a geo- chemical modeling applied to an off-shore Italian carbonatic saline aquifer potential suitable to geological CO2 storage are here presented and discussed. Deep well data, still covered by industrial confidentiality, show that the saline aquifer, includes six Late Triassic-Early Jurassic carbonatic formations at the depth of 2500-3700 m b.s.l. These formations, belonging to Tuscan Nappe, consist of porous limestones (mainly calcite) and marly limestones sealed, on the top, by an effective and thick cap-rock (around 2500 m) of clay flysch belonging to the Liguride Units. The evaluation of the potential geochemical impact of CO2 storage and the quantification of water-gas-rock reactions (solubility and mineral trapping) of injection reservoir have been performed by the PRHEEQC (V2.11) Software Package via corrections to the code default ther- modynamic database to obtain a more realistic modelling. The main modifications to the Software Package are, as follows: i) addition of new solid phases, ii) variation of the CO2 supercritical fugacity and solubility under reservoir conditions, iii) addi- tion of kinetic rate equations of several minerals and iv) calculation of reaction sur- face area. Available site-specific data include only basic physical parameters such as temperature, pressure, and salinity of the formation waters. Rocks sampling of each considered formation in the contiguous in-shore zones was carried out. Mineralogy was determined by X-Ray diffraction analysis and Scanning Electronic Microscopy on thin sections. As chemical composition of the aquifer pore water is unknown, this has been inferred by batch modeling assuming thermodynamic equilibrium between minerals and a NaCl equivalent brine at reservoir conditions (up to 135 ̊C and 251 atm). Kinetic modelling was carried out for isothermal conditions (135 ̊C), under a CO2 injection constant pressure of 251 atm, between: a) bulk mineralogy of the six formations constituting the aquifer, and b) pre-CO2 injection water. The kinetic evolu- tion of the CO2 -rich brines interacting with the host-rock minerals performed over 100 years after injection suggests that solubility trapping is prevailing in this early stage of CO2 injection. Further and detailed multidisciplinary studies on rock properties, geochemical and micro seismic monitoring and 3D reservoir simulation are necessary to better characterize the potential storage site and asses the CO2 storage capacity.544 309 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Modellizzazione delle variazioni composizionali delle specie dell’azoto (NH4 +, NO2 -, NO3 -) nelle acque di falda del Comune di Arezzo (Toscana)♦
(2008-03-28); ; ; ; Gli elementi chimici disciolti nelle acque continentali provengono dall’alterazione della crosta terrestre. L’acqua erode e dissolve i minerali delle rocce attraverso l’alterazione chimica avvalendosi del contributo dei gas presenti in atmosfera o nel sottosuolo. Il nitrato, una delle sostanze responsabili delle più gravi forme di inquinamento delle acque nei paesi in via di sviluppo, è un nutriente essenziale per la crescita delle piante e rappresenta un anello fondamentale del ciclo biogeochimico dell'azoto, in quanto viene prodotto dai batteri a partire dall'azoto atmosferico. In quantità eccessive il nitrato può essere dannoso per gli uomini e per gli animali. Elevati livelli di nitrato nell'acqua sono causati in larga misura dall'uso di fertilizzanti ricchi di nitrato e dal letame. In questo contesto, le condizioni redox delle acque naturali, che controllano la speciazione dei composti dell’azoto, sono altamente variabili perché controllate prevalentemente dall’attività biologica. In particolare, il bilancio fra i due processi dell’attività biologica, la fotosintesi e la respirazione (o decomposizione della sostanza organica), determina la presenza nel sistema di condizioni ossidanti o riducenti. I composti dell’azoto possono quindi essere considerati utili indicatori dello stato di salute di un acquifero superficiale. In questo lavoro sono analizzati i dati relativi ai tenori delle specie dell’azoto NH4 +, NO2 - e NO3 - relativi ad acque di falda campionate nell’area aretina nel corso della realizzazione dell’Atlante Geochimico delle Acque di Falda e di Scorrimento Superficiale del Comune di Arezzo. I dati sono analizzati proponendo nuove metodologie grafiche e numeriche per visualizzare lo stato del territorio nei confronti della pressione antropica come rilevata dal comportamento spaziale e temporale delle specie suddette.216 518 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , THERMO-KINETIC MODELING OF THE EVOLUTION OF THE CO2-RICH WEYBURN BRINES AT THE RESERVOIR INFERRED CONDITIONS (P, T, WATER-GAS CHEMISTRY): FIRST RESULTS OF A NEW APPROACH
(2006-03-22); ; ; ; EnCana’s CO2 injection EOR project at Weyburn (Saskatchewan, Canada) is the focal point of a multi-faceted research program, sponsored by IEA GHG R&D and numerous international industrial and government partners including the European Community (BGS, BRGM, INGV and GEUS research providers), to find co-optimization of “CO2-EOR Production” and “CO2 -Geological Storage”, addressed to environmental purposes, in the frame of the Kyoto Agreement Policies. The Weyburn oil-pull is recovered from Midale Beds (at the depth of 1300-1500 m). This formation consists of Mississipian shallow marine carbonate-evaporites that can be subdivided into two units: i) the dolomitic “Marly” and ii) the underlying calcitic “Vuggy”, sealed by an anhydrite cap. Presently, around 3 billions mc of supercritical CO2 have been injected into the “Phase A1”injection area that includes around 90 oil producers, 30 water injectors and 30 CO2 injection wells, build up since September 2000. INGV has carried out a geochemical monitoring programme -approximately thrice yearly from pre-injection (“Baseline” trip, August 2000) to September 2004- performing trace element and dissolved gas analysis along with fluids sampling surveys, the latter being performed by the Canadian partners. The experimental data are the base of a geochemical modelling, i.e. the main goal of the present study. In the past, assumptions and gap-acceptance have been made in the literature in the frame of the geochemical modelling of CO2 geological storage, in order to reconstruct the reservoir conditions (pressure, pH and boundary conditions). As these parameters of deep fluids cannot be measured in-situ, all this information must be computed by a a posteriori procedure involving the analytical data. In this work we proposed an approach to geochemical modeling in order to:: i) reconstruct the in-situ reservoir chemical composition (including pH) and ii) evaluate the boundary conditions (e.g. pCO2, pH2S), necessary to implement the reaction path modelling. This is the starting point to assess the geochemical impact of CO2 into the oil reservoir and, as main target, to quantify water-gas-rock reactions. Our geochemical modelling procedure is based on the available data such as: a) bulk mineralogy of the Marly and Vuggy zones; b) average gas-cap composition and c) pre-and post-CO2 injection selected water samples from Midale Beds. The PRHEEQC (V2.11) Software Package was used to reconstruct the in-situ reservoir composition by calculating the chemical equilibrium among the various phases at reservoir temperature (60°C) and pressure (150 bars) conditions by suitable thermodynamic corrections to code database. Then, we identified possible compositions of the initially reservoir liquid phases, always taking into account the case histories of the Marly and Vuggy units. The inverse modelling simulation (IMS) was then performed in order to calculate the amounts of mass transfer of liquid, gas and solid phases that accounted for changes in the water chemistry between the 2000 and 2003 data-sets. IMS calculations suggest that the reservoir underwent mineralogical changes, such as precipitation of chalcedony, gypsum and kaolinite and dissolution of anhydrite and k-feldspar. Calcite dissolution is predicted, but the precipitation of others carbonates (dolomite, dawsonite and siderite) can also occur. Finally, we modelled the geochemical impact of CO2 injection on Weyburn reservoir subjected to both local equilibrium and kinetically controlled reactions. All experimental data and thermo-kinetic modeling of the evolution of the CO2-rich Weyburn brine interacting with host rock minerals performed over 100 years after injection confirm that “solubility trapping” is prevailing in this early stage of CO2 injection. Further and detailed studies on the evolution of the CO2-rich Weyburn brine is one of main aims of this study in the framework of a PhD programme between the INGV of Rome and the Department of Earth Sciences of Florence.150 208
