Radon and thoron emission from lithophysae-rich tuff under increasing deformation: An experimental study
Language
English
Obiettivo Specifico
2.3. TTC - Laboratori di chimica e fisica delle rocce
Status
Published
JCR Journal
JCR Journal
Peer review journal
Yes
Journal
Issue/vol(year)
/37 (2010)
Publisher
American Geophysical Union
Pages (printed)
L05305
Date Issued
March 12, 2010
Subjects
Abstract
Radon and thoron emissions from lithophysae‐rich tuff
under increasing deformation are measured to determine
how mechanical damage affects gas emission levels in
tuffs. Mechanical properties of rocks under stresses should
be carefully considered to properly interpret data from
geochemical field monitoring. Two samples are uniaxially
loaded up to failure, while two others are unloaded at the
end of the elastic phase, in order to achieve the highest
compaction of existing pores. Changes in the porosity of
deformed samples are evidenced by helium pycnometer
and microscopy analyses. Radon and thoron exhalation
rates are measured on groups of two samples by alpha
spectrometer technique. Results show that tuff samples
are characterised by a dual porosity consisting of a
macroporosity, given by isolated large pores with sizes
from mm‐ up to cm‐scale and a microporosity ranging
between microns to hundreds of microns. At the end of
the elastic phase pervasive pore collapse is observed, due
to the closure of the cm‐scale macropores. This is
mirrored by a significant decrease of radon and thoron
release. After failure, a further reduction of porosity in the
rock adjacent to the fault planes is observed due to
extensive closure of both macropores and micropores. At
this stage radon and thoron emissions increase. The
formation of new exhaling surfaces is the main carrier of
the bulk increase of radon and thoron exhalations, strongly
prevailing over the densification carried out from the
compaction mechanisms. In terms of volcanic hazard,
negative anomalies in radon emissions should be
considered as indicators of forthcoming ruptures. Key
words: radon and thoron exhalation, tuff deformation,
seismic precursor.
under increasing deformation are measured to determine
how mechanical damage affects gas emission levels in
tuffs. Mechanical properties of rocks under stresses should
be carefully considered to properly interpret data from
geochemical field monitoring. Two samples are uniaxially
loaded up to failure, while two others are unloaded at the
end of the elastic phase, in order to achieve the highest
compaction of existing pores. Changes in the porosity of
deformed samples are evidenced by helium pycnometer
and microscopy analyses. Radon and thoron exhalation
rates are measured on groups of two samples by alpha
spectrometer technique. Results show that tuff samples
are characterised by a dual porosity consisting of a
macroporosity, given by isolated large pores with sizes
from mm‐ up to cm‐scale and a microporosity ranging
between microns to hundreds of microns. At the end of
the elastic phase pervasive pore collapse is observed, due
to the closure of the cm‐scale macropores. This is
mirrored by a significant decrease of radon and thoron
release. After failure, a further reduction of porosity in the
rock adjacent to the fault planes is observed due to
extensive closure of both macropores and micropores. At
this stage radon and thoron emissions increase. The
formation of new exhaling surfaces is the main carrier of
the bulk increase of radon and thoron exhalations, strongly
prevailing over the densification carried out from the
compaction mechanisms. In terms of volcanic hazard,
negative anomalies in radon emissions should be
considered as indicators of forthcoming ruptures. Key
words: radon and thoron exhalation, tuff deformation,
seismic precursor.
References
Al‐Harthi, A. A., R. M. Al‐Amri, and W. M. Shehata (1999), The porosity
and engineering properties of vesicular basalt in Saudi Arabia, Eng.
Geol. Amsterdam, 54, 313‐320, doi:10.1016/S0013-7952(99)00050-2.
Avar, B. B., and N. W. Hudyma (2007), Observations on the influence of
lithophysae on elastic (Young”s) modulus and uniaxial compressive
strength of Topopah Spring Tuff at Yucca Mountain, Nevada, USA,
Int . J. Rock Mech. Min. Sci . , 44, 266–270, doi:10.1016/ j .
ijrmms.2006.06.003.
Baud, P., A. Schubnel, and T.‐f. Wong (2000), Dilatancy, compaction and
failure mode in Solnhofen limestone, J. Geophys. Res., 105, 19,289–
19,303, doi:10.1029/2000JB900133.
Birchard, G. F., and W. F. Libby (1980), Soil radon concentration changes
preceding and four magnitude 4.2–4.7 earthquakes on the San Jacinto
fault in southern California, J. Geophys. Res., 85, 3100–3106,
doi:10.1029/JB085iB06p03100.
Bolt, B. A. (1993), Earthquakes and Geological Discovery, Sci. Am. Lib.,
New York.
Fuenkajorn, K., and J. J. K. Daemen (1992), An empirical strength criterion
for heterogeneous tuff, Eng. Geol., 32, 209–223, doi:10.1016/0013-7952
(92)90049-5.
Gervino, G., C. Cigolini, A. Lavagno, C. Marino, P. Prati, L. Pruiti, and
G. Zangari (2004), Modelling temperature distributions and radon
emission at Stromboli Volcano using a non‐extensive statistical approach,
Phys. A, 340, 402–409.
Gokceoglu, C. (2002), A fuzzy triangular chart to predict the uniaxial compressive
strength of the Ankara Agglomerates from their petrographic
composition, Eng. Geol. Amsterdam, 66, 39–51, doi:10.1016/S0013-
7952(02)00023-6.
Holub, R. F., and B. T. Brady (1981), The effect of stress on radon emanation
from rock, J. Geophys. Res., 86, 1776–1784, doi:10.1029/
JB086iB03p01776.
Hudyma, N., B. Burcin Avarb, and M. Karakouzian (2004), Compressive
strength and failure modes of lithophysae‐rich Topopah Spring Tuff specimens
and analog models containing cavities, Eng. Geol. Amsterdam,
73, 179‐190, doi:10.1016/j.enggeo.2004.01.003.
Neri, M., B. Behncke, M. Burton, G. Galli, S. Giammanco, E. Pecora,
E. Privitera, and D. Reitano (2006), Continuous soil radon monitoring
during the July 2006 Etna eruption, Geophys. Res. Lett., 33, L24316,
doi:10.1029/2006GL028394.
Nishimura, S., and I. Katsura (1990), Radon in soil gas: Applications in
exploration and earthquake prediction, in Geochemistry of Gaseous
Elements and Compounds, edited by E. M. Durrance et al., pp. 497–
533, Theophrastus, Athens.
Planini, J., V. Radolic, and B. Vukovic (2004), Radon as an earthquake
precursor, Nucl. Instrum. Methods Phys. Res., Sect. A, 530, 568–574,
doi:10.1016/j.nima.2004.04.209.
Ramola, R. C., Y. Prasad, G. Prasad, S. Kumar, and V. M. Choubey
(2008), Soil‐gas radon as seismotectonic indicator in Garhwal Himalaya,
Appl. Radiat. Isot., 66, 1523–1530, doi:10.1016/j.apradiso.2008.04.006.
Roeloffs, E. (1999), Radon and rock deformation, Nature, 399, 104–105,
doi:10.1038/20072.
Silver, P. G., and H. Wakita (1996), A search for earthquake precursors,
Science, 273, 77–78, doi:10.1126/science.273.5271.77.
Sonmez, H., E. Tuncay, and C. Gokceoglu (2004), Models to predict the
uniaxial compressive strength and the modulus of elasticity for Ankara
Agglomerate, Int. J. Rock Mech. Min. Sci., 41, 717–729, doi:10.1016/
j.ijrmms.2004.01.011.
Sonmez, H., C. Gokceoglua, E. W. Medley, E. Tuncay, and H. A. Nefeslioglu
(2006), Estimating the uniaxial compressive strength of a volcanic bimrock,
Int. J. Rock Mech. Min. Sci., 43, 554–561, doi:10.1016/j.
ijrmms.2005.09.014.
Talwani, P., W. S. Moore, and J. Chiang (1980), Radon anomalies and microearthquakes
at Lake Jocasse, J. Geophys. Res., 85, 3079–3088,
doi:10.1029/JB085iB06p03079.Tillerson, J. R., and F. B. Nimick (1984), Geoengineering properties of
potential repository units at Yucca Mountain, southern Nevada, Sandia
National Labs Rep., SAND84‐0221, Albuquerque, N. M.
Trique, M., P. Richon, F. Perrier, J. P. Avouac, and J. C. Sabroux (1999),
Radon emanation and electric potential variations associated with transient
deformation near reservoir lakes, Nature , 399, 137–141,
doi:10.1038/20161.
Tuccimei, P., M. Moroni, and D. Norcia (2006), Simultaneous determination
of 222Rn and 220Rn exhalation rates from building materials
used in Central Italy with accumulation chambers and a continuous
solid state alpha detector: influence of particle size, humidity and precursors
concentration, Appl. Radiat. Isot., 64, 254–263, doi:10.1016/j.
apradiso.2005.07.016.
Tuccimei, P., S. Vinciguerra, S. Moretti, S. Mollo, and M. Castelluccio
(2009), Relating changes in radon exhalation to increasing loading in
rocks: New insights from rock deformation laboratory experiments,
paper presented at European Geosciences Union General Assembly,
Vienna, 19–24 April.
Vajdova, V., P. Baud, and T.‐f. Wong (2004), Compaction, dilatancy and
failure in porous carbonate rocks, J. Geophys. Res., 109, B10406,
doi:10.1029/2003JB002942.
Vinciguerra, S., C. Trovato, P. G. Meredith, P. M. Benson, C. Troise, and
G. De Natale (2006), Understanding the seismic velocity structure of
Campi Flegrei Caldera (Italy): From the laboratory to the field scale,
Pure Appl. Geophys., 163, 2205–2221, doi:10.1007/s00024-006-0118-y.
Vinciguerra, S., P. Del Gaudio, M. T. Mariucci, F. Marra, P. G. Meredith,
P. Montone, S. Pierdominici, and P. Scarlato (2009), Physical properties
of tuffs from a scientific borehole at Alban hills volcanic district (central
Italy), Tectonophysics, 471, 161–169, doi:10.1016/j.tecto.2008.08.010.
and engineering properties of vesicular basalt in Saudi Arabia, Eng.
Geol. Amsterdam, 54, 313‐320, doi:10.1016/S0013-7952(99)00050-2.
Avar, B. B., and N. W. Hudyma (2007), Observations on the influence of
lithophysae on elastic (Young”s) modulus and uniaxial compressive
strength of Topopah Spring Tuff at Yucca Mountain, Nevada, USA,
Int . J. Rock Mech. Min. Sci . , 44, 266–270, doi:10.1016/ j .
ijrmms.2006.06.003.
Baud, P., A. Schubnel, and T.‐f. Wong (2000), Dilatancy, compaction and
failure mode in Solnhofen limestone, J. Geophys. Res., 105, 19,289–
19,303, doi:10.1029/2000JB900133.
Birchard, G. F., and W. F. Libby (1980), Soil radon concentration changes
preceding and four magnitude 4.2–4.7 earthquakes on the San Jacinto
fault in southern California, J. Geophys. Res., 85, 3100–3106,
doi:10.1029/JB085iB06p03100.
Bolt, B. A. (1993), Earthquakes and Geological Discovery, Sci. Am. Lib.,
New York.
Fuenkajorn, K., and J. J. K. Daemen (1992), An empirical strength criterion
for heterogeneous tuff, Eng. Geol., 32, 209–223, doi:10.1016/0013-7952
(92)90049-5.
Gervino, G., C. Cigolini, A. Lavagno, C. Marino, P. Prati, L. Pruiti, and
G. Zangari (2004), Modelling temperature distributions and radon
emission at Stromboli Volcano using a non‐extensive statistical approach,
Phys. A, 340, 402–409.
Gokceoglu, C. (2002), A fuzzy triangular chart to predict the uniaxial compressive
strength of the Ankara Agglomerates from their petrographic
composition, Eng. Geol. Amsterdam, 66, 39–51, doi:10.1016/S0013-
7952(02)00023-6.
Holub, R. F., and B. T. Brady (1981), The effect of stress on radon emanation
from rock, J. Geophys. Res., 86, 1776–1784, doi:10.1029/
JB086iB03p01776.
Hudyma, N., B. Burcin Avarb, and M. Karakouzian (2004), Compressive
strength and failure modes of lithophysae‐rich Topopah Spring Tuff specimens
and analog models containing cavities, Eng. Geol. Amsterdam,
73, 179‐190, doi:10.1016/j.enggeo.2004.01.003.
Neri, M., B. Behncke, M. Burton, G. Galli, S. Giammanco, E. Pecora,
E. Privitera, and D. Reitano (2006), Continuous soil radon monitoring
during the July 2006 Etna eruption, Geophys. Res. Lett., 33, L24316,
doi:10.1029/2006GL028394.
Nishimura, S., and I. Katsura (1990), Radon in soil gas: Applications in
exploration and earthquake prediction, in Geochemistry of Gaseous
Elements and Compounds, edited by E. M. Durrance et al., pp. 497–
533, Theophrastus, Athens.
Planini, J., V. Radolic, and B. Vukovic (2004), Radon as an earthquake
precursor, Nucl. Instrum. Methods Phys. Res., Sect. A, 530, 568–574,
doi:10.1016/j.nima.2004.04.209.
Ramola, R. C., Y. Prasad, G. Prasad, S. Kumar, and V. M. Choubey
(2008), Soil‐gas radon as seismotectonic indicator in Garhwal Himalaya,
Appl. Radiat. Isot., 66, 1523–1530, doi:10.1016/j.apradiso.2008.04.006.
Roeloffs, E. (1999), Radon and rock deformation, Nature, 399, 104–105,
doi:10.1038/20072.
Silver, P. G., and H. Wakita (1996), A search for earthquake precursors,
Science, 273, 77–78, doi:10.1126/science.273.5271.77.
Sonmez, H., E. Tuncay, and C. Gokceoglu (2004), Models to predict the
uniaxial compressive strength and the modulus of elasticity for Ankara
Agglomerate, Int. J. Rock Mech. Min. Sci., 41, 717–729, doi:10.1016/
j.ijrmms.2004.01.011.
Sonmez, H., C. Gokceoglua, E. W. Medley, E. Tuncay, and H. A. Nefeslioglu
(2006), Estimating the uniaxial compressive strength of a volcanic bimrock,
Int. J. Rock Mech. Min. Sci., 43, 554–561, doi:10.1016/j.
ijrmms.2005.09.014.
Talwani, P., W. S. Moore, and J. Chiang (1980), Radon anomalies and microearthquakes
at Lake Jocasse, J. Geophys. Res., 85, 3079–3088,
doi:10.1029/JB085iB06p03079.Tillerson, J. R., and F. B. Nimick (1984), Geoengineering properties of
potential repository units at Yucca Mountain, southern Nevada, Sandia
National Labs Rep., SAND84‐0221, Albuquerque, N. M.
Trique, M., P. Richon, F. Perrier, J. P. Avouac, and J. C. Sabroux (1999),
Radon emanation and electric potential variations associated with transient
deformation near reservoir lakes, Nature , 399, 137–141,
doi:10.1038/20161.
Tuccimei, P., M. Moroni, and D. Norcia (2006), Simultaneous determination
of 222Rn and 220Rn exhalation rates from building materials
used in Central Italy with accumulation chambers and a continuous
solid state alpha detector: influence of particle size, humidity and precursors
concentration, Appl. Radiat. Isot., 64, 254–263, doi:10.1016/j.
apradiso.2005.07.016.
Tuccimei, P., S. Vinciguerra, S. Moretti, S. Mollo, and M. Castelluccio
(2009), Relating changes in radon exhalation to increasing loading in
rocks: New insights from rock deformation laboratory experiments,
paper presented at European Geosciences Union General Assembly,
Vienna, 19–24 April.
Vajdova, V., P. Baud, and T.‐f. Wong (2004), Compaction, dilatancy and
failure in porous carbonate rocks, J. Geophys. Res., 109, B10406,
doi:10.1029/2003JB002942.
Vinciguerra, S., C. Trovato, P. G. Meredith, P. M. Benson, C. Troise, and
G. De Natale (2006), Understanding the seismic velocity structure of
Campi Flegrei Caldera (Italy): From the laboratory to the field scale,
Pure Appl. Geophys., 163, 2205–2221, doi:10.1007/s00024-006-0118-y.
Vinciguerra, S., P. Del Gaudio, M. T. Mariucci, F. Marra, P. G. Meredith,
P. Montone, S. Pierdominici, and P. Scarlato (2009), Physical properties
of tuffs from a scientific borehole at Alban hills volcanic district (central
Italy), Tectonophysics, 471, 161–169, doi:10.1016/j.tecto.2008.08.010.
Description
An edited version of this paper was published by AGU. Copyright (2010) American Geophysical Union.
Type
article
File(s)![]()
Name
8_Tuccimei et al._2010_Geophysical Research Letters_37_L05305.pdf
Description
Main article
Size
226.83 KB
Format
Adobe PDF
Checksum (MD5)
The MD5 message-digest algorithm can be used to verify the integrity of the file that you have uploaded. You can calculate its value locally via tools that are generally available in each operative system like md5sum
b89a79c2909cf98d2cbad477d59578dd
