The survey and mapping of sand-boil landforms related to the Emilia 2012 earthquakes: preliminary results
Author(s)
Language
English
Obiettivo Specifico
4.4. Scenari e mitigazione del rischio ambientale
Status
Published
JCR Journal
JCR Journal
Peer review journal
Yes
Journal
Issue/vol(year)
4/55 (2012)
Publisher
INGV
Pages (printed)
727-733
Date Issued
2012
Subjects
Abstract
Sand boils, which are also known as sand blows or sand
volcanoes, are among the most common superficial effects
induced by high-magnitude earthquakes. These generally
occur in or close to alluvial plains when a strong earthquake
(M >5) strikes on a lens of saturated and unconsolidated
sand deposits that are constrained between silt-clay layers
[Ambraseys 1988, Carter and Seed 1988, Galli 2000, Tuttle
2001, Obermeier et al. 2005], where the sediments are converted
into a fluid suspension. The liquefaction phenomena
requires the presence of saturated and uncompacted sand,
and a groundwater table near the ground surface. This geological–
geomorphological setting is common and widespread
for the Po Plain (Italy) [Castiglioni et al. 1997]. The
Po Plain (ca. 46,000 km2) represents 15% of the Italian territory.
It hosts a population of about 20 million people
(mean density of 450 people/km2) and many infrastructures.
Thus, the Po Plain is an area of high vulnerability
when considering the liquefaction potential in the case of a
strong earthquake. Despite the potential, such phenomena
are rarely observed in northern Italy [Cavallin et al. 1977,
Galli 2000], because strong earthquakes are not frequent in
this region; e.g., historical data report soil liquefaction near
Ferrara in 1570 (M 5.3) and in Argenta 1624 (M 5.5) [Prestininzi
and Romeo 2000, Galli 2000]. In the Emilia quakes
of May 20 and 29, 2012, the most widespread coseismic effects
were soil liquefaction and ground cracks, which occurred
over wide areas in the Provinces of Modena, Ferrara,
Bologna, Reggio Emilia and Mantova (Figure 1). These were
the causes of considerable damage to buildings and the infrastructure.
The soil liquefaction and ground cracks were
accompanied by sand boils, which are described in this report.
The spatial distribution and geomorphological setting
of sand boils and ground cracks are also described here. A
detailed three-dimensional (3D) reconstruction of these features
is also presented, which was carried out using terrestrial
photogrammetry.
Since archeological times, fluvial ridges, and in general
sandy deposits on low plains have been the preferred sites for
human infrastructure, colonial houses, roads, etc. Therefore,
it is very important to understand how the local topography/
morphology interacts in the liquefaction processes. Numerous
distinctive seismic landforms were generated by the
May 2012 strong earthquakes (seven with M >5), and in particular,
sand boils and ground fractures. The sand-boil landforms,
also known as sand craters or sand volcanoes, are
formed by low mounds of sand that have been extruded
from fractures [Tuttle 2001]. The cone is a generally shortlived
structure that naturally collapses, starting from the center
holes that mark the water retreat back into the fracture.
Sand boils also occurred along larger cracks (with decimetric
lateral and vertical displacements). Here, the upper scarps
block the formation of craters and allow the deposition of a
sandy layer several centimeters thick (e.g. ca. 4 cm in the San
Carlo crack), on the lower side of the steep slope. These landforms
are highly vulnerable to erosion. After a few weeks,
they are washed out by rain, destroyed by human activity, or
masked by growing crops. Thus, ground surveys that investigate
these events have to be carried out as soon as possible
[Panizza et al. 1981]. In this report, we present preliminary
results using methods to map the detailed micro-morphology
of some representative liquefaction features (Figure 2)
that normally disappear for the aforementioned reasons, or
that are recorded only in qualitative terms.
volcanoes, are among the most common superficial effects
induced by high-magnitude earthquakes. These generally
occur in or close to alluvial plains when a strong earthquake
(M >5) strikes on a lens of saturated and unconsolidated
sand deposits that are constrained between silt-clay layers
[Ambraseys 1988, Carter and Seed 1988, Galli 2000, Tuttle
2001, Obermeier et al. 2005], where the sediments are converted
into a fluid suspension. The liquefaction phenomena
requires the presence of saturated and uncompacted sand,
and a groundwater table near the ground surface. This geological–
geomorphological setting is common and widespread
for the Po Plain (Italy) [Castiglioni et al. 1997]. The
Po Plain (ca. 46,000 km2) represents 15% of the Italian territory.
It hosts a population of about 20 million people
(mean density of 450 people/km2) and many infrastructures.
Thus, the Po Plain is an area of high vulnerability
when considering the liquefaction potential in the case of a
strong earthquake. Despite the potential, such phenomena
are rarely observed in northern Italy [Cavallin et al. 1977,
Galli 2000], because strong earthquakes are not frequent in
this region; e.g., historical data report soil liquefaction near
Ferrara in 1570 (M 5.3) and in Argenta 1624 (M 5.5) [Prestininzi
and Romeo 2000, Galli 2000]. In the Emilia quakes
of May 20 and 29, 2012, the most widespread coseismic effects
were soil liquefaction and ground cracks, which occurred
over wide areas in the Provinces of Modena, Ferrara,
Bologna, Reggio Emilia and Mantova (Figure 1). These were
the causes of considerable damage to buildings and the infrastructure.
The soil liquefaction and ground cracks were
accompanied by sand boils, which are described in this report.
The spatial distribution and geomorphological setting
of sand boils and ground cracks are also described here. A
detailed three-dimensional (3D) reconstruction of these features
is also presented, which was carried out using terrestrial
photogrammetry.
Since archeological times, fluvial ridges, and in general
sandy deposits on low plains have been the preferred sites for
human infrastructure, colonial houses, roads, etc. Therefore,
it is very important to understand how the local topography/
morphology interacts in the liquefaction processes. Numerous
distinctive seismic landforms were generated by the
May 2012 strong earthquakes (seven with M >5), and in particular,
sand boils and ground fractures. The sand-boil landforms,
also known as sand craters or sand volcanoes, are
formed by low mounds of sand that have been extruded
from fractures [Tuttle 2001]. The cone is a generally shortlived
structure that naturally collapses, starting from the center
holes that mark the water retreat back into the fracture.
Sand boils also occurred along larger cracks (with decimetric
lateral and vertical displacements). Here, the upper scarps
block the formation of craters and allow the deposition of a
sandy layer several centimeters thick (e.g. ca. 4 cm in the San
Carlo crack), on the lower side of the steep slope. These landforms
are highly vulnerable to erosion. After a few weeks,
they are washed out by rain, destroyed by human activity, or
masked by growing crops. Thus, ground surveys that investigate
these events have to be carried out as soon as possible
[Panizza et al. 1981]. In this report, we present preliminary
results using methods to map the detailed micro-morphology
of some representative liquefaction features (Figure 2)
that normally disappear for the aforementioned reasons, or
that are recorded only in qualitative terms.
References
Ambraseys, N.N. (1988). Engineering Seismology, Earthquake
Engineering and Structural Dynamics, vol. 17, Elsevier,
Amsterdam, 1-105.
Balista, C., M. Calzolari, P. Campagnoli, A. Cardarelli, M.
Cattani, V. Corazza, C. Corti, S. Gelichi, A. Gianferrari, N.
Giordani, D. Labate, L. Malnati, R. Mussati, G. Pellacani,
S. Pellegrini, R. Tarpini and C. Zanasi (2003). Atlante dei
Beni Archeologici della Provincia di Modena, Vol. I, All'
Insegna del Giglio, Firenze.
Burrato, P.F., F. Ciucci and G. Valensise (2003). An inventory
of river anomalies in the Po Plain, northern Italy: evidence
for active blind thrust faulting, Annals of Geophysics,
46 (5), 865-882.
Carter, D.P., and H.B. Seed (1988). Liquefaction Potential of
Sand Deposits Under Low Levels of Excitation, Report
No. UCB/EERC-81/11, College of Engineering, University
of California, Berkeley, 1-119.
Castaldini, D. (1984). Esempio di studio morfologico e geolitologico
in un'area di pianura: il territorio del comune di
Quistello (Provincia di Mantova), Atti della Società dei
Naturalisti e Matematici di Modena, 115 , 47-76.
Castaldini, D., and S. Raimondi (1985). Geomorfologia dell'area
di Pianura Padana compresa fra Cento, Finale
Emilia e S. Agostino, Atti della Società dei Naturalisti e
Matematici di Modena, 116, 147-176.Castaldini, D. (1989a). Evoluzione della rete idrografica centropadana
in epoca protostorica e storica, In: Atti del Convegno
"Insediamenti e viabilità nell'alto ferrarese dall'Età
Romana al Medioevo" (Cento, 8-9 maggio 1987), Accademia
delle Scienze di Ferrara, 115-134.
Castaldini, D. (1989b). Geomorfologia della bassa Pianura
Padana modenese e dei territori limitrofi, In: Mirandola e
le valli, immagini e documenti, Tip. Golnelli, Mirandola,
25-37.
Castaldini, D., M. Mazzucchelli and V. Pignatti (1992). Geomorfologia
e geochimica dei sedimenti del paleoalveo dei
Barchessoni (San Martino Spino, bassa pianura modenese),
In: M. Calzolari and L. Malnati (eds.), Gli Etruschi
nella Bassa Modenese, Gruppo studi Bassa modenese,
207-224.
Castaldini, D., M. Marchetti and A. Cardarelli (2009). Geomorphological
and archaeological aspects in the central
Po Plain (northern Italy), In: M. De Dapper, F. Vermeulen,
S. Deprez and D. Taelman (eds.), Ol'man River. Geo-archaeological
aspects of rivers and river plains (ARGU 5),
Universiteit Gent Academia Press, Belgium, 193- 211.
Castiglioni, G.B., et al. (1997). Carta Geomorfologica della
Pianura Padana, MURST, 3 fogli, 1:250.000, LAC, Firenze.
Castiglioni, G.B., and G.B. Pellegrini (2001). Illustrative Notes
of the Geomorphological Map of Po Plain, Supplement
to Geogr. Fis. Din. Quat., IV, 1-208.
Cavallin, A., B. Martinis and G. Sfrondrini (1977). Effetti geologici
del terremoto: fenditure nel terreno e "vulcanelli"
di sabbia, In: B. Martinis B. (ed.), Studio geologico dell'
area maggiormente colpita dal terremoto friuliano del
1976, Riv. Ital.Paleontol. S., 83, 369-393.
Galli, P. (2000). New empirical relationships between magnitude
and distance for liquefaction, Tectonophysics, 324,
169-187.
Landuzzi, A., R. Nichols and G.B. Vai (1995). Sand volcanoes
in the Marnoso-Arenacea formation (Miocene, northern
Apennines, Italy): new evidence of paleoseismicity, In: L.
Serva and D. Burton Slemmons (eds.), Perspectives in paleosismology,
Special Publication n. 6, Association of Engineering
Geologists, 49-61.
Miller, V.C. (1953). A quantitative geomorphic study of
drainage basin characteristics in the Clinch Mountain
area, Virginia and Tennessee, Technical Report No.3,
Contract N6 ONR 271-300, Columbia University, Department
of Geology.
Montenat, C., P. Barrier, P.O. d'Estevou and C. Hibsch (2007).
Seismites: an attempt at critical analysis and classification,
Sediment. Geol., 196, 5-30.
Obermeier, S.F. (1996). Use of liquefaction induced features
for paleoseismic analysis, Eng. Geol., 44, 1-76.
Obermeier, S.F., S.M. Olson and R.A. Green (2005). Field occurrences
of liquefaction-induced features: a primer for
engineering geologic analysis of paleoseismic shaking,Eng. Geol., 76, 209-234.
Panizza, M., G. Bollettinari, A. Carton, D. Castaldini and S.
Piacente (1981). Considerazioni sul "pronto intervento"
in occasione di un terremoto distruttivo, Rendiconti della
Società Geologica Italiana, 4, 707-708.
Prestininzi, A., and R.W. Romeo (2000). Earthquake-induced
ground failures in Italy, Eng. Geol., 58, 387-397.
Schumm, S. (1956). Evolution of drainage systems and slopes
in badland at Perth Amboy, New Jersey, Bull. Geol. Soc.
Am., 67, 597-646.
Szeliski, R. (2011). Computer Vision: Algorithms and Applications,
Springer-Verlag, London, 1-812.
Toscani, G., P. Burrato, D. Di Bucci, S. Seno and G. Valensise
(2009). Plio-Quaternary tectonic evolution of the northern
Apennines thrust fronts (Bologna-Ferrara section,
Italy): seismotectonic implications, B. Soc. Geol. Ital, 128,
605-613.
Tuttle, M.P. (2001). The use of liquefaction features in paleoseismology:
lessons learned in the New Madrid seismic
zone, central United States, J. Seismol., 5, 361-380.
Ullman, S. (1979). The interpretation of structure from motion,
Proc. R. Soc. Lond., B.203, 405-426.
Verhoeven, G. (2011). Taking computer vision aloft - archaeological
three-dimensional reconstructions from aerial
photographs with PhotoScan, Archaeol. Prospect., 18,
67-73.
Engineering and Structural Dynamics, vol. 17, Elsevier,
Amsterdam, 1-105.
Balista, C., M. Calzolari, P. Campagnoli, A. Cardarelli, M.
Cattani, V. Corazza, C. Corti, S. Gelichi, A. Gianferrari, N.
Giordani, D. Labate, L. Malnati, R. Mussati, G. Pellacani,
S. Pellegrini, R. Tarpini and C. Zanasi (2003). Atlante dei
Beni Archeologici della Provincia di Modena, Vol. I, All'
Insegna del Giglio, Firenze.
Burrato, P.F., F. Ciucci and G. Valensise (2003). An inventory
of river anomalies in the Po Plain, northern Italy: evidence
for active blind thrust faulting, Annals of Geophysics,
46 (5), 865-882.
Carter, D.P., and H.B. Seed (1988). Liquefaction Potential of
Sand Deposits Under Low Levels of Excitation, Report
No. UCB/EERC-81/11, College of Engineering, University
of California, Berkeley, 1-119.
Castaldini, D. (1984). Esempio di studio morfologico e geolitologico
in un'area di pianura: il territorio del comune di
Quistello (Provincia di Mantova), Atti della Società dei
Naturalisti e Matematici di Modena, 115 , 47-76.
Castaldini, D., and S. Raimondi (1985). Geomorfologia dell'area
di Pianura Padana compresa fra Cento, Finale
Emilia e S. Agostino, Atti della Società dei Naturalisti e
Matematici di Modena, 116, 147-176.Castaldini, D. (1989a). Evoluzione della rete idrografica centropadana
in epoca protostorica e storica, In: Atti del Convegno
"Insediamenti e viabilità nell'alto ferrarese dall'Età
Romana al Medioevo" (Cento, 8-9 maggio 1987), Accademia
delle Scienze di Ferrara, 115-134.
Castaldini, D. (1989b). Geomorfologia della bassa Pianura
Padana modenese e dei territori limitrofi, In: Mirandola e
le valli, immagini e documenti, Tip. Golnelli, Mirandola,
25-37.
Castaldini, D., M. Mazzucchelli and V. Pignatti (1992). Geomorfologia
e geochimica dei sedimenti del paleoalveo dei
Barchessoni (San Martino Spino, bassa pianura modenese),
In: M. Calzolari and L. Malnati (eds.), Gli Etruschi
nella Bassa Modenese, Gruppo studi Bassa modenese,
207-224.
Castaldini, D., M. Marchetti and A. Cardarelli (2009). Geomorphological
and archaeological aspects in the central
Po Plain (northern Italy), In: M. De Dapper, F. Vermeulen,
S. Deprez and D. Taelman (eds.), Ol'man River. Geo-archaeological
aspects of rivers and river plains (ARGU 5),
Universiteit Gent Academia Press, Belgium, 193- 211.
Castiglioni, G.B., et al. (1997). Carta Geomorfologica della
Pianura Padana, MURST, 3 fogli, 1:250.000, LAC, Firenze.
Castiglioni, G.B., and G.B. Pellegrini (2001). Illustrative Notes
of the Geomorphological Map of Po Plain, Supplement
to Geogr. Fis. Din. Quat., IV, 1-208.
Cavallin, A., B. Martinis and G. Sfrondrini (1977). Effetti geologici
del terremoto: fenditure nel terreno e "vulcanelli"
di sabbia, In: B. Martinis B. (ed.), Studio geologico dell'
area maggiormente colpita dal terremoto friuliano del
1976, Riv. Ital.Paleontol. S., 83, 369-393.
Galli, P. (2000). New empirical relationships between magnitude
and distance for liquefaction, Tectonophysics, 324,
169-187.
Landuzzi, A., R. Nichols and G.B. Vai (1995). Sand volcanoes
in the Marnoso-Arenacea formation (Miocene, northern
Apennines, Italy): new evidence of paleoseismicity, In: L.
Serva and D. Burton Slemmons (eds.), Perspectives in paleosismology,
Special Publication n. 6, Association of Engineering
Geologists, 49-61.
Miller, V.C. (1953). A quantitative geomorphic study of
drainage basin characteristics in the Clinch Mountain
area, Virginia and Tennessee, Technical Report No.3,
Contract N6 ONR 271-300, Columbia University, Department
of Geology.
Montenat, C., P. Barrier, P.O. d'Estevou and C. Hibsch (2007).
Seismites: an attempt at critical analysis and classification,
Sediment. Geol., 196, 5-30.
Obermeier, S.F. (1996). Use of liquefaction induced features
for paleoseismic analysis, Eng. Geol., 44, 1-76.
Obermeier, S.F., S.M. Olson and R.A. Green (2005). Field occurrences
of liquefaction-induced features: a primer for
engineering geologic analysis of paleoseismic shaking,Eng. Geol., 76, 209-234.
Panizza, M., G. Bollettinari, A. Carton, D. Castaldini and S.
Piacente (1981). Considerazioni sul "pronto intervento"
in occasione di un terremoto distruttivo, Rendiconti della
Società Geologica Italiana, 4, 707-708.
Prestininzi, A., and R.W. Romeo (2000). Earthquake-induced
ground failures in Italy, Eng. Geol., 58, 387-397.
Schumm, S. (1956). Evolution of drainage systems and slopes
in badland at Perth Amboy, New Jersey, Bull. Geol. Soc.
Am., 67, 597-646.
Szeliski, R. (2011). Computer Vision: Algorithms and Applications,
Springer-Verlag, London, 1-812.
Toscani, G., P. Burrato, D. Di Bucci, S. Seno and G. Valensise
(2009). Plio-Quaternary tectonic evolution of the northern
Apennines thrust fronts (Bologna-Ferrara section,
Italy): seismotectonic implications, B. Soc. Geol. Ital, 128,
605-613.
Tuttle, M.P. (2001). The use of liquefaction features in paleoseismology:
lessons learned in the New Madrid seismic
zone, central United States, J. Seismol., 5, 361-380.
Ullman, S. (1979). The interpretation of structure from motion,
Proc. R. Soc. Lond., B.203, 405-426.
Verhoeven, G. (2011). Taking computer vision aloft - archaeological
three-dimensional reconstructions from aerial
photographs with PhotoScan, Archaeol. Prospect., 18,
67-73.
Type
article
File(s)![]()
Name
NINFO_bozze.pdf
Description
Pre-print
Size
3.19 MB
Format
Adobe PDF
Checksum (MD5)
The MD5 message-digest algorithm can be used to verify the integrity of the file that you have uploaded. You can calculate its value locally via tools that are generally available in each operative system like md5sum
aa0308324331a05a73e2eacf60330938
