Skip to main content
The search returned 6 results
Now showing 1 - 6 of 6
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Influence of instruments on the H/V spectral ratios of ambient vibrations

    For an optimal analysis of the H/V curve, it appears necessary to check the instrument signal to noise ratio in the studied frequency band, to ensure that the signal from the ground noise is well above the internal noise. We assess the reliability and accuracy of various digitizers, sensors and/or digitizer-sensor couples. Although this study is of general interest for any kind of seismological study, we emphasize the influence of equipment on H/V analysis results. To display the impact of the instrumental part on the H/V behavior, some series of tests have been carried out following a step-by-step procedure: first, the digitizers have been tested in the lab (sensitivity, internal noise...), then the three components sensors, still in the lab, and finally the usual user digitizers-sensors couple in lab and outdoors. In general, the digitizer characteristics, verified during this test, correspond well to the manufacturer specifications, however, depending on the digitizer, the quality of the digitized waveform can be very good to very poor, with variation from a channel to another channel (gain, time difference etc.). It appears very clearly that digitizers need a warming up time before the recording to avoid problems in the low-frequency range. Regarding the sensors, we recommend strongly to avoid the use of “classical” accelerometers (i.e., usual force balance technology). The majority of tested seismometers (broadband and short period, even 4.5 Hz) can be used without problems from 0.4 to 25 Hz. In all cases, the instrumentation should be checked first to verify that it works well for the defined study aim, but also to define its limit of use (frequency, sensitivity...).
      173  21
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Derivation of Vs30 f rom dispersion curve: skipping the inversion step?

    In the framework of the EU-NERIES project, 20 sites among all European strong motion sites in Italy, Greece, T urkey and France were selected to be representative of most common soil classes, and for which shear-wave velocities from borehole measurements (cross-hole and down-hole tests) are available. Passive (array noise) and active experiments have been carried out at these sites in order to evaluate the ability of surface waves technique to provide reliable estimates of shear-wave velocity profiles. In order to stay cheap and feasible, active seismic experiments involving 24 geophones and hammer source were carried out at all sites. Data were processed by using the MASW technique and Rayleigh and Love waves dispersion curves were retrieved from 5-10 Hz to 30-50 Hz. Passive array experiments were also performed by using 8 seismological stations linked with wireless connections and monitored with near real-time processing. Combining up to four different arrays with aperture ranging from 10 m and to 900 m, Rayleigh and Love waves dispersion curves were derived over a broad frequency range (from 0.5 Hz up to 45 Hz) by using the FK and MSPAC techniques. At about 75% sites, dispersion curves from ambient vibration and MASW are in good agreement over the overlapping frequency band. T he other 25% sites correspond to complex geometrical site structures. Whatever the site, passive experiments are shown to be very suitable to retrieve accurate estimates of phase velocities at high frequency (over 20-30 Hz). T his experiment also clearly outlined the limited penetration depth (comprised between 15 and 25 m) of the MASW technique. Inversion of dispersion curves to derive shear-wave profiles and EC8 site class (which is mainly based on Vs30) is a difficult and highly debated issue. Here we test an alternative to get average shear-wave profiles and especially Vs30 from the dispersion curves only. For these 20 sites, we show that site classes may be estimated directly from the dispersion curves. T heses results are confirmed by an extensive study involving about 800 velocity profiles from real sites.
      268  263
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Joint inversion of Rayleigh wave ellipticity and spatial autocorrelation measurements

    The local soil structure (i.e. shear and pressure wave velocities) can be obtained by inversion of dispersion curves ranging over a sufficiently large frequency band. However, measurements of such dispersion curves using ambient seismic vibrations require a large number of seismometers and a long measuring time. As a simple alternative, we propose to invert Rayleigh wave ellipticity obtained by ambient seismic noise measurements at a single site using a method based on the random decrement technique (Hobiger et al., 2009). Indeed, the freSeismological Research Letters Volume 81, Number 2 March/April 2010 305 quency-dependency of Rayleigh wave ellipticity is tightly related to the shear wave profile of the soil. However, as different soil structures can result in the same ellipticity curve (e.g. homothetic structures in velocity and thickness), the inversion of ellipticity curves alone is ambiguous. Therefore, additional measurements fixing the shearwave velocity in the superficial layers have to be included into the inversion process. We suggest using a small number of seismic stations to measure spatial autocorrelation curves. In this way, three seismic sensors and one hour of measurements can be sufficient to invert the local soil structure. We will present the method to extract the Rayleigh wave ellipticity curve, show which parts of the ellipticity curve have to be included in the inversion process and demonstrate the benefit of the additional spatial autocorrelation curve measurements. Then, we will present an example application to real noise data collected within the framework of the European NERIES project at well-known European accelerometric sites and the results will be compared to th
      192  55
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    EMPIRICAL EVALUATION OF THE HORIZONTAL-TO-VERTICAL SPECTRAL RATIO TECHNIQUE: RESULTS FROM THE “SESAME” PROJECT

    In order to empirically evaluate the horizontal-to-vertical (H/V) spectral ratio technique, ambient noise measurements performed in about two hundred sites mainly in Europe where weak or/and strong motion data was recorded. Standard Information Sheets (SIS) and earthquake information data were included in the SESAME [Site EffectS assessment using AMbient Excitations] project database, specially designed to facilitate data selection. All noise recordings were processed with JSESAME software to calculate (H/V) spectral ratio, whereas weak and strong motion earthquake recordings were processed with a similarly standardized procedure. For the latter, (H/V) receiver function for all sites were calculated. Experimental site transfer functions obtained from earthquake recordings were compared with the (H/V) spectral ratios from noise recordings in terms of fundamental frequency, amplification bandwidth and amplification level. Similarities and differences between (H/V) spectral ratio of noise and earthquake recordings are presented and discussed. In addition, a dense grid of noise measurements were performed within urban environment of cities affected by strong earthquake (Greece: Thessaloniki, Kalamata, Italy: Palermo). It seems that the (H/V) spectral ratio may satisfactorily indicate areas favorable to the occurrence of higher damage in urban environment. However, quantitative correlation between (H/V) spectral ratio properties and damage distribution (macroseismic intensity, damage grades) in some cases, is difficult to be established given the complexity of parameters involved.
      273  763
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Sesame Project - Deliverable D20-04 - WP04 H/V Technique : Empirical Evaluation - Comparisons of Damage Distribution in Modern Urban Areas with Results from (H/V) Spectral Ratio

    In this Report comparisons of seismic damage distribution with the (H/V) spectral ratio results is attempted, under the framework of the SESAME Project (Site Effects Assessment Using Ambient Excitations, EC-RGD, Project No. EVG1-CT-2000-00026 SESAME), Task A (H/V technique), Work Package 04 (WP04– H/V Technique: Empirical Evaluation).
      244  279
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Sesame Project - Deliverable D04-04 - Report of the WP04 H/V Technique : Empirical Evaluation - Homogeneous Data Set of Noise and Earthquake Recordings at Many Sites

    In this Report the homogeneous data set of earthquake and noise recordings at many sites that is generated under the framework of the SESAME Project (Site Effects Assessment Using Ambient Excitations, EC- RGD, Project No. EVG1-CT-2000-00026 SESAME), Task A (H/V technique), Work Package 04 (WP04– H/V Technique: Empirical Evaluation), is presented. Three main topics are included in the Report: (a) The Standard Information Sheet (SIS) structure, (b) The SESAME Ascii Format (SAF) files, and (c) The SESAME SIS-database. The SIS compiled in this sub-task and SAF format adopted for all data, constitute a homogeneous data set to be processed for further scientific results in the framework of the WP04. In addition, the SIS-database is going to facilitate data selection and management.
      294  710