universita' Praga
4 results
Filters
Settings
The search returned 4 results
Now showing 1 - 4 of 4
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Task 5 - Potenza - Deliverable D17: Bedrock shaking scenarios
(2007-07); ; ; ; The main goal of this report is the computation of the bedrock seismic scenarios in the Potenza city (Southern Italy) to be used for evaluating damage scenarios (described in PS3-Deliverables D18-D19-D24). This area represents one of the prediction case studies, planned in the framework of Project S3 which aim is the production of ground shaking scenarios for high and moderate magnitude earthquakes. The area around Potenza was affected by several destructive earthquakes in historical time (Table 2.1.1) and a number of individual sources representing the causative faults of single seismic events with magnitude up to 7 were identified. Deeper and smaller faults are present very close to the Potenza city, generating events with M up to 5.7 (1990 Potenza earthquake). Due to the involved source-to-site distances (about 25 km) and to the computation resolution of the simulation techniques, the site is represented by a single point. In total 9 faults were identified and the deterministic shaking scenarios are computed for each of them. The following strategy is adopted to provide ground motions. We compute shaking scenarios at level 1, using a simplified simulation technique (DSM, Pacor et al.; 2005) for all the faults. By these simulations we identify the three faults (F3, F7. and F8) producing the maximum expected shaking at the Potenza city, in terms of peak ground acceleration, peak ground velocity and Housner intensity. Based on these results, simulations at level 2, using the broad band technique HIC (Gallovic and Brokeshova, 2007) have been performed at Potenza for F3, F7 and F8 sources. For the Potenza city, we decided to predict the shaking scenarios at level 2, in order to provide suitable estimates of the low frequency ground motion (e.g. velocity time series) and engineering parameters (e.g. Arias intensity) strictly related to the duration of the signals. For each source, we generated hundreds of rupture models varying slip distribution, nucleation points and rupture velocity, and for each model we simulated the acceleration time series by HIC. Then we computed the probability density functions (PDF) of the ground motion parameters (PGA, PGV, PGD, Arias and Housner intensities) and estimated several statistical quantities in order to select families of accelerograms to be used for damage analysis: mean and associated standard deviation, median, 75% percentile, 84% percentile, mode, minimum and maximum. Finally we provided to the engineering Research Unit 6 of this project three sets of 7 accelerograms, having ground motion parameters equal to the statistical requirements computed by the synthetic distributions. The first set includes 7 accelerograms (three components), each of them having PGA equal to the mean, median, mode, 75-percentile, 84-percentile, minimum and maximum values of the PGA distribution. The second set and third sets include 7 accelerograms (horizontal components only), having PGA and Housener Intensity in the neighborhood of the median values of the corresponding distributions. A further comparison of adopted procedure for the predicted ground motion at Potenza was performed with respect to stochastic ground motions generated with EXSIM method (Motazedian and Atkinson; 2005). Even if the scenarios modelling was carried out varying different kinematic parameters, the statistical parameter were quite similar. Finally to provide shaking scenarios in term of macroseismic intensity, we applied a probabilistic empirical approach, developed in Progetto DPC-INGV S1.156 578 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , 168 270 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Task 6 - Gubbio - Deliverable D20: Bedrock shaking scenarios
(2007-07); ; ; ; The main goal of Task 6 is the computation of the bedrock and site seismic scenarios in the Gubbio town and in the Gubbio basin (Central Italy). This area represents one of the prediction case studies, planned in the framework of Project S3 which aims at simulating ground shaking scenarios for moderate magnitude earthquakes. Deterministic shaking scenarios, described in this report, are computed for the Maximum Credible Earthquake. This is associated with two sources capable of generating an earthquake with M equal to 6 and located at about 10km from the sites. Starting from these sources bedrock shaking scenarios at different level of complexity are computed by ground motion prediction equations (scenarios of level 0), high frequency (f>0.5Hz) simulations (scenarios of level 1) and broad band (0-20 Hz) simulations (scenarios of level 2). However since many sites have to be simulated for accurately sampling the basin, the bedrock ground motions for evaluating the seismic response of the valley are generated at level 1. For four test sites a comparison between time series computed at different levels of complexity have been performed in order to verify the approximations introduced in level 1. Before computing the predicted shaking scenarios, we evaluate the modelling capability of the adopted simulation techniques reproducing the observed ground motions occurred during the 1984 Gubbio earthquake (M 5.7). Finally we apply the probabilistic-deterministic approach for a characteristic earthquake scenario proposed by Convertito et al. (2006) to perform hazard analysis considering the two seismogenic faults at three sites of interest in the Gubbio area (paragraph 3.3). In this way, respect to the deterministic approach, we produce ‘dynamic shaking scenarios’ introducing the time variable. The shaking scenarios generated in the Gubbio area allow us to show how the prediction of the ground motion can be tackled using different methodologies and which strategy should be followed to select mean shaking scenario. As the available information increases, we could gradually adopt approaches more and more sophisticated and provide shaking scenarios that account for specific effects related to the source and propagation (e.g., directivity, radiation pattern distribution,…). Furthermore, the adoption of different approaches allows a cross check of the results guaranteeing the reliability of the ground motion estimates.166 318 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: Open Access , Task 3 - Molise - Deliverable D7: Validation shaking scenarios.
(2007-07); ; ; ; The main goal of this report is the computation of the bedrock seismic motion at 5 municipalities located in the Molise area (Bonefro, S.Giuliano, Colletorto, S.Croce di Magliano, Ripabottoni, hereafter referred to as sites BNF, SGI, CLT, SCM and RPB, respectively). This area represents one of the validation case studies, planned in the framework of Project S3 which aim is the production of ground shaking scenarios for moderate magnitude earthquakes. Indeed, the recently occurred Molise earthquake represents a proper opportunity to compare synthetic simulations with real data. Acceleration time series were recorded during the October 31, 2002 and November 1, 2002 main shocks by analog and digital instruments managed by the Italian Civil Protection Department [DPC-SSN, 2004] while acceleration and velocity records were collected during the first month of seismic activity by DPC, INGV, INOGS, Dip.Te.Ris.(Genoa) (see §2.1 and Deliverable D6). Both strong and weak motion data were employed to infer regional ground motion prediction equations and spectral attenuation models (§2.3 and §2.4) while acceleration time series recorded during the first main shock by nearby stations were used to constrain the seismogenic sources of the October 31 and November 1, 2002 twin earthquakes (§4.1). Bedrock shaking scenarios at different level of complexity were produced by ground motion prediction equations (scenarios of level 0, §4.2), high frequency (f>1Hz) simulations (scenarios of level I, §4.3) and broad band (0-12 Hz) simulations (scenarios of level II, §4.4). Comparison of results obtained with different simulations methods confirms the complexity of the Molise area as regard to both seismogenic and attenuation properties of the crust. Especially for this area the ground motion prediction is constrained by the demand of simulations reproducing different features of the seismic wavefield. In particular, the input motion for site effect modelling, performed at sites located in the epicentral area, was computed with a broad band technique able to reproduce the complete wave field in the frequency band 0-10 Hz in terms of acceleration time series (scenarios of level II scenarios).209 566
