Skip to main content
The search returned 2 results
Now showing 1 - 2 of 2
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    Atmospheric sources and sinks of volcanogenic elements in a basaltic volcano (Etna, Italy)

    This study reports on the first quantitative assessment of the geochemical cycling of volcanogenic elements, from their atmospheric release to their deposition back to the ground. Etna’s emissions and atmospheric depositions were characterised for more than 2 years, providing data on major and trace element abundance in both volcanic aerosols and bulk depositions. Volcanic aerosols were collected from 2004 to 2007, at the summit vents by conventional filtration techniques. Precipitation was collected, from 2006 to 2007, in five rain gauges, at various altitudes around the summit craters. Analytical results for volcanic aerosols showed that the dominant anions were S, Cl, and F, and that the most abundant metals were K, Ca, Mg, Al, Fe, and Ti (1.5–50 lg m 3). Minor and trace element concentrations ranged from about 0.001 to 1 lg m 3. From such analysis, we derived an aerosol mass flux ranging from 3000 to 8000 t a 1. Most analysed elements had higher concentrations close to the emission vent, confirming the prevailing volcanic contribution to bulk deposition. Calculated deposition rates were integrated over the whole Etna area, to provide a first estimate of the total deposition fluxes for several major and trace elements. These calculated deposition fluxes ranged from 20 to 80 t a 1 (Al, Fe, Si) to 0.01–0.1 t a 1 (Bi, Cs, Sc, Th, Tl, and U). Comparison between volcanic emissions and atmospheric deposition showed that the amount of trace elements scavenged from the plume in the surrounding of the volcano ranged from 0.1% to 1% for volatile elements such as As, Bi, Cd, Cs, Cu, Tl, and from 1% to 5% for refractory elements such as Al, Ba, Co, Fe, Ti, Th, U, and V. Consequently, more than 90% of volcanogenic trace elements were dispersed further away, and may cause a regional scale impact. Such a large difference between deposition and emission fluxes at Mt. Etna pointed to relatively high stability and long residence time of aerosols in the plume.
      573  41
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Restricted ,

    The source motion of 2003 Bam (Iran) earthquake constrained by satellite and ground-based geodetic data

    The interpretation of coseismic surface deformation measurements through inversion techniques is of major importance to understand the mechanical behaviour of a seismic fault. Dense geodetic data sets in the vicinity of the ruptured fault provide unique constraints on detailed fault geometry and slip distribution at depth, making them complementary to seismological data. Bam earthquake (Mw 6.6, 2003 December 26) induced surface deformation has been precisely mapped by Envisat ASAR interferometry and by subpixel correlation techniques applied to Spot-5 and ASAR amplitude images. These oblique and horizontal estimations of deformation have been completed with one levelling profile along the main road crossing the rupture from west to east. We process these data (separately and jointly) in a two-step inversion technique, within the elastic half-space theory framework. Our objective is to determine the dislocation model at depth that satisfies simultaneously all the geodetic constraints. Also, we estimate the relative contribution of each geodetic data set to this inversion process. We first use a stochastic direct approach called neighbourhood algorithm in order to estimate the average characteristics of the rupture, and their relative uncertainty. Constraining in this way the geometry of the ruptured fault, we then linearize the inverse problem and compute the slip distribution on the fault using a standard weighted least-square technique, assuming the solution is smooth to some degree. At each step, we discuss the optimal models, their stability as well as the relative influence of each data set on the derived models parameters. Our preferred model reveals a shallow dislocation on a quasi-vertical fault, slightly dipping towards east. The slip vector has a strike-slip component as high as 2 m, while the dip-slip component seems negligible. However, the estimation of the resolution matrices emphasizes the fact that the details of deep fault slip distribution remain out of the scope of this ill-conditioned inverse problem. Yet, our preferred model suggests a main dislocation limited at depth between 1 and 6 km. By contrast, the aftershocks observed in the months following the earthquake are located just beneath the estimated main shock.
      172  29