Skip to main content
The search returned 3 results
Now showing 1 - 3 of 3
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    An Update of the NeQuick-Corr Topside Ionosphere Modeling Based on New Datasets

    A new analytical formula for H0, one of the three parameters (H0, g, and r) on which the NeQuick model is based to describe the altitude profile of the electron density above the F2-layer peak height hmF2, has recently been proposed. This new analytical representation of H0, called H0,corr, relies on numerical grids based on two different types of datasets. On one side, electron density observations by the Swarm satellites over Europe from December 2013 to September 2018, and on the other side, IRI UP (International Reference Ionosphere UPdate) maps over Europe of the critical frequency of the ordinary mode of propagation associated with the F2 layer, foF2, and hmF2, at 15 min cadence for the same period. The new NeQuick topside representation based on H0,corr, hereafter referred to as NeQuick-corr, improved the original NeQuick topside representation. This work updates the numerical grids of H0,corr by extending the underlying Swarm and IRI UP datasets until December 2021, thus allowing coverage of low solar activity levels, as well. Moreover, concerning Swarm, besides the original dataset, the calibrated one is considered, and corresponding grids of H0,corr calculated. At the same time, the role of g is investigated, by considering values different from the reference one, equal to 0.125, currently adopted. To understand what are the best H0,corr grids to be considered for the NeQuick-corr topside representation, vertical total electron content data for low, middle, and high latitudes, recorded from five low-Earth-orbit satellite missions (COSMIC/FORMOSAT-3, GRACE, METOP, TerraSAR-X, and Swarm) have been analyzed. The updated H0,corr grids based on the original Swarm dataset with a value for g = 0.15, and the updated H0,corr grids based on the calibrated Swarm dataset with a value for g = 0.14, are those for which the best results are obtained. The results show that the performance of the different NeQuick-corr models is reliable also for low latitudes, even though these are outside the spatial domain for which the H0,corr grids were obtained, and are dependent on solar activity.
      68  124
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    Modeling the Topside Ionosphere Effective Scale Height through In Situ Electron Density Observations by Low-Earth-Orbit Satellites

    In this work, we aim to characterize the effective scale height at the ionosphere F2-layer peak (H0) by using in situ electron density (Ne) observations by Langmuir Probes (LPs) onboard the China Seismo-Electromagnetic Satellite (CSES—01). CSES—01 is a sun-synchronous satellite orbiting at an altitude of ~500 km, with descending and ascending nodes at ~14:00 local time (LT) and ~02:00 LT, respectively. Calibrated CSES—01 LPs Ne observations for the years 2019–2021 provide information in the topside ionosphere, whereas the International Reference Ionosphere model (IRI) provides Ne values at the F2-layer peak altitude for the same time and geographical coordinates as CSES—01. CSES—01 and IRI Ne datasets are used as anchor points to infer H0 by assuming a linear scale height in the topside representation given by the NeQuick model. COSMIC/FORMOSAT—3 (COSMIC—1) radio occultation (RO) data are used to constrain the vertical gradient of the effective scale height in the topside ionosphere in the linear approximation. With the CSES—01 dataset, we studied the global behavior of H0 for daytime (~14:00 LT) and nighttime (~02:00 LT) conditions, different seasons, and low solar activity. Results from CSES—01 observations are compared with those obtained through Swarm B satellite Ne-calibrated measurements and validated against those from COSMIC—1 RO for similar diurnal, seasonal, and solar activity conditions. H0 values modeled by using CSES—01 and Swarm B-calibrated observations during daytime both agree with corresponding values obtained directly from COSMIC—1 RO profiles. Differently, H0 modeling for nighttime conditions deserves further investigation because values obtained from both CSES—01 and Swarm B-calibrated observations show remarkable and spatially localized differences compared to those obtained through COSMIC—1. Most of the H0 mismodeling for nighttime conditions can probably to be attributed to a sub-optimal spatial representation of the F2-layer peak density made by the underlying IRI model. For comparison, H0 values obtained with non-calibrated CSES—01 and Swarm B Ne observations are also calculated and discussed. The methodology developed in this study for the topside effective scale height modeling turns out to be applicable not only to CSES—01 satellite data but to any in situ Ne observation by low-Earth-orbit satellites orbiting in the topside ionosphere.
      366  166
  • Some of the metrics are blocked by your 
    Item type:Publication, Access status: Open Access ,

    On the low-latitude NeQuick topside ionosphere mismodelling: The role of parameters H0, g, and r

    This paper deals with the well-known mismodelling characterizing the NeQuick topside ionosphere at low latitudes, i.e., the fact that the model keeps the two electron density humps typical of the equatorial ionization anomaly as the altitude increases from the height of the F2-layer electron density peak, without merging them in a single peak above the geomagnetic equator as expected. This is because the NeQuick topside ionosphere modelling strongly depends on several bottomside ionosphere parameters, which causes an essential coupling between the topside and the bottomside that in many cases behave differently. This means that this kind of topside ionosphere modelling may lead to inaccurate results, as it is the maintenance at low latitudes of the electron density double hump structure in the topside as the altitude increases. On the base of some recently published results, this paper analyzes the role played by the three NeQuick scale height parameters H0, g and r in the description of the electron density above the F2 layer peak height. The results of this work pave the way for a possible solution of this low-latitude NeQuick topside ionosphere mismodelling.
      182  167