Options
Borehole breakout analysis: results from the AND-2A Well
Author(s)
Type
Poster session
Language
English
Obiettivo Specifico
3.2. Tettonica attiva
Status
Unpublished
Conference Name
Issued date
2010
Conference Location
San Francisco (California, USA)
Keywords
Abstract
To define the present-day stress field in the upper crust and to understand the recent tectonic activity in Antarctica, a study of breakout measurements along AND-2A well was performed. The borehole breakout is an important indicator of horizontal stress orientation and occurs when the stresses around the borehole exceed that required to cause compressive failure of the borehole wall (Bell and Gough, 1979; Zoback et al., 1985, Bell, 1990). The enlargement of the wellbore is caused by the development of intersecting conjugate shear planes that cause pieces of the borehole wall to spall off. Around a vertical borehole, stress concentration is greatest in the direction of the minimum horizontal stress (Shmin), hence, the long axes of borehole breakouts are oriented approximately perpendicular to the maximum horizontal stress orientation (SHmax). The orientation of breakouts along the AND-2A well was measured using acoustic (BHTV) and mechanical (Four-Arm Caliper) tools. Borehole televiewer (BHTV) provides an
acoustic "image" of the borehole wall (360 degree coverage) and gives detailed information for investigation
of fractures and stress analysis. The four-arm caliper is the oldest technique for borehole breakout identification and it is included in routine dipmeter logs. A quality value has been assigned to the well results
in agreement with the World Stress Map quality ranking scheme (Zoback, 1992; Heidback et al., 2010) based mainly on the number, accuracy, and length of breakout measurements. The result is presented
as rose diagram of the breakout directions where the length of each peak is proportional to the frequency and the width to the variance of its gaussian curve. We have analyzed the following curves to recognize the breakout: the azimuth of Pad 1 (P1az), the drift azimuth (HAZI), the two calipers with respect to the bit size (BZ) curve and the curve relative to the deviation of the well. The AND-2A Four-Arm Caliper data cover a depth interval between 637 down to 997 mbsl, that corresponds to 360 m of logged interval.
We have distinguished breakouts and some washouts only in the interval from 753 to 825 mbsl. From borehole televiewer images, we have data from 398 mbsl down to 1136 mbsl. The BHTV worked well showing a lot of interesting features such as many bedding, lamination and fractures (natural and induced) but poor breakouts. The rare breakouts have also a small size (called protobreakouts) but they are consistent
with induced features. Considering the breakout result from caliper and BHTV, the AND-2A borehole is unfortunately classified as D quality. This means that to obtain a reliable active stress field of the area it
is necessary to compare this result with other available data.
acoustic "image" of the borehole wall (360 degree coverage) and gives detailed information for investigation
of fractures and stress analysis. The four-arm caliper is the oldest technique for borehole breakout identification and it is included in routine dipmeter logs. A quality value has been assigned to the well results
in agreement with the World Stress Map quality ranking scheme (Zoback, 1992; Heidback et al., 2010) based mainly on the number, accuracy, and length of breakout measurements. The result is presented
as rose diagram of the breakout directions where the length of each peak is proportional to the frequency and the width to the variance of its gaussian curve. We have analyzed the following curves to recognize the breakout: the azimuth of Pad 1 (P1az), the drift azimuth (HAZI), the two calipers with respect to the bit size (BZ) curve and the curve relative to the deviation of the well. The AND-2A Four-Arm Caliper data cover a depth interval between 637 down to 997 mbsl, that corresponds to 360 m of logged interval.
We have distinguished breakouts and some washouts only in the interval from 753 to 825 mbsl. From borehole televiewer images, we have data from 398 mbsl down to 1136 mbsl. The BHTV worked well showing a lot of interesting features such as many bedding, lamination and fractures (natural and induced) but poor breakouts. The rare breakouts have also a small size (called protobreakouts) but they are consistent
with induced features. Considering the breakout result from caliper and BHTV, the AND-2A borehole is unfortunately classified as D quality. This means that to obtain a reliable active stress field of the area it
is necessary to compare this result with other available data.
File(s)
Loading...
Name
Poster_2010_AGU.pdf
Size
1.48 MB
Format
Adobe PDF
Checksum (MD5)
ff925efd45ad25b7d6c48fb034e501e4